[ 0.000000] Linux version 4.7.0-rc6-drm-intel-nightly-ww29-commit-e549c0b+ (gfx@GM-GFX-QA02) (gcc version 4.9.3 (Ubuntu 4.9.3-8ubuntu2~14.04) ) #1 SMP Mon Jul 11 08:23:47 CDT 2016 [ 0.000000] Command line: vmlinuz root=/dev/sda2 initrd=initrd.img idle=halt log_buf_len=4M i915.enable_rc6=1 i915.preliminary_hw_support=1 drm.debug=0xe i915.enable_guc_submission=1 [ 0.000000] KERNEL supported cpus: [ 0.000000] Intel GenuineIntel [ 0.000000] AMD AuthenticAMD [ 0.000000] Centaur CentaurHauls [ 0.000000] x86/fpu: xstate_offset[3]: 960, xstate_sizes[3]: 64 [ 0.000000] x86/fpu: xstate_offset[4]: 1024, xstate_sizes[4]: 64 [ 0.000000] x86/fpu: Supporting XSAVE feature 0x001: 'x87 floating point registers' [ 0.000000] x86/fpu: Supporting XSAVE feature 0x002: 'SSE registers' [ 0.000000] x86/fpu: Supporting XSAVE feature 0x008: 'MPX bounds registers' [ 0.000000] x86/fpu: Supporting XSAVE feature 0x010: 'MPX CSR' [ 0.000000] x86/fpu: Enabled xstate features 0x1b, context size is 1088 bytes, using 'standard' format. [ 0.000000] x86/fpu: Using 'eager' FPU context switches. [ 0.000000] e820: BIOS-provided physical RAM map: [ 0.000000] BIOS-e820: [mem 0x0000000000000000-0x0000000000057fff] usable [ 0.000000] BIOS-e820: [mem 0x0000000000058000-0x0000000000058fff] reserved [ 0.000000] BIOS-e820: [mem 0x0000000000059000-0x000000000009dfff] usable [ 0.000000] BIOS-e820: [mem 0x000000000009e000-0x00000000000fffff] reserved [ 0.000000] BIOS-e820: [mem 0x0000000000100000-0x000000000effffff] usable [ 0.000000] BIOS-e820: [mem 0x000000000f000000-0x0000000012151fff] reserved [ 0.000000] BIOS-e820: [mem 0x0000000012152000-0x0000000077fddfff] usable [ 0.000000] BIOS-e820: [mem 0x0000000077fde000-0x0000000079d8dfff] reserved [ 0.000000] BIOS-e820: [mem 0x0000000079d8e000-0x0000000079dedfff] ACPI NVS [ 0.000000] BIOS-e820: [mem 0x0000000079dee000-0x0000000079e2dfff] ACPI data [ 0.000000] BIOS-e820: [mem 0x0000000079e2e000-0x000000007ac26fff] usable [ 0.000000] BIOS-e820: [mem 0x000000007ac27000-0x000000007ac27fff] ACPI NVS [ 0.000000] BIOS-e820: [mem 0x000000007ac28000-0x000000007ac51fff] reserved [ 0.000000] BIOS-e820: [mem 0x000000007ac52000-0x000000007affffff] usable [ 0.000000] BIOS-e820: [mem 0x000000007b000000-0x000000007fffffff] reserved [ 0.000000] BIOS-e820: [mem 0x00000000e0000000-0x00000000e3ffffff] reserved [ 0.000000] BIOS-e820: [mem 0x00000000fed01000-0x00000000fed01fff] reserved [ 0.000000] BIOS-e820: [mem 0x0000000100000000-0x000000047fffffff] usable [ 0.000000] NX (Execute Disable) protection: active [ 0.000000] efi: EFI v2.50 by EDK II [ 0.000000] efi: ACPI=0x79e2d000 ACPI 2.0=0x79e2d014 ESRT=0x79d59000 SMBIOS=0x7813f000 SMBIOS 3.0=0x7813d000 PROP=0x7a061920 [ 0.000000] efi: requested map not found. [ 0.000000] esrt: ESRT header is not in the memory map. [ 0.000000] SMBIOS 3.0.0 present. [ 0.000000] e820: update [mem 0x00000000-0x00000fff] usable ==> reserved [ 0.000000] e820: remove [mem 0x000a0000-0x000fffff] usable [ 0.000000] e820: last_pfn = 0x480000 max_arch_pfn = 0x400000000 [ 0.000000] MTRR default type: uncachable [ 0.000000] MTRR fixed ranges enabled: [ 0.000000] 00000-9FFFF write-back [ 0.000000] A0000-BFFFF uncachable [ 0.000000] C0000-FFFFF write-protect [ 0.000000] MTRR variable ranges enabled: [ 0.000000] 0 base 0000000000 mask 7F80000000 write-back [ 0.000000] 1 base 007C000000 mask 7FFC000000 uncachable [ 0.000000] 2 base 007B000000 mask 7FFF000000 uncachable [ 0.000000] 3 base 0100000000 mask 7F00000000 write-back [ 0.000000] 4 base 0200000000 mask 7F00000000 write-back [ 0.000000] 5 base 0300000000 mask 7F00000000 write-back [ 0.000000] 6 base 0400000000 mask 7F80000000 write-back [ 0.000000] 7 base 00FF800000 mask 70FF800000 write-combining [ 0.000000] 8 disabled [ 0.000000] 9 disabled [ 0.000000] x86/PAT: Configuration [0-7]: WB WC UC- UC WB WC UC- WT [ 0.000000] e820: last_pfn = 0x7b000 max_arch_pfn = 0x400000000 [ 0.000000] Scanning 1 areas for low memory corruption [ 0.000000] Base memory trampoline at [ffff880000098000] 98000 size 24576 [ 0.000000] Using GB pages for direct mapping [ 0.000000] BRK [0x0223d000, 0x0223dfff] PGTABLE [ 0.000000] BRK [0x0223e000, 0x0223efff] PGTABLE [ 0.000000] BRK [0x0223f000, 0x0223ffff] PGTABLE [ 0.000000] BRK [0x02240000, 0x02240fff] PGTABLE [ 0.000000] BRK [0x02241000, 0x02241fff] PGTABLE [ 0.000000] BRK [0x02242000, 0x02242fff] PGTABLE [ 0.000000] log_buf_len: 4194304 bytes [ 0.000000] early log buf free: 257428(98%) [ 0.000000] RAMDISK: [mem 0x722a0000-0x747ebfff] [ 0.000000] ACPI: Early table checksum verification disabled [ 0.000000] ACPI: RSDP 0x0000000079E2D014 000024 (v02 INTEL ) [ 0.000000] ACPI: XSDT 0x0000000079E04188 0000E4 (v01 INTEL EDK2 00000003 BRXT 01000013) [ 0.000000] ACPI: FACP 0x0000000079E25000 00010C (v05 INTEL EDK2 00000003 BRXT 0100000D) [ 0.000000] ACPI BIOS Warning (bug): 32/64X length mismatch in FADT/Pm1aEventBlock: 32/16 (20160422/tbfadt-624) [ 0.000000] ACPI BIOS Warning (bug): Invalid length for FADT/Pm1aEventBlock: 16, using default 32 (20160422/tbfadt-708) [ 0.000000] ACPI: DSDT 0x0000000079E15000 00958C (v02 INTEL EDK2 00000003 BRXT 0100000D) [ 0.000000] ACPI: FACS 0x0000000079DDC000 000040 [ 0.000000] ACPI: SSDT 0x0000000079E2B000 0003C6 (v02 INTEL Tpm2Tabl 00001000 INTL 20150818) [ 0.000000] ACPI: TPM2 0x0000000079E2A000 000034 (v03 00000000 00000000) [ 0.000000] ACPI: UEFI 0x0000000079DE4000 000042 (v01 INTEL EDK2 00000002 BRXT 01000013) [ 0.000000] ACPI: BDAT 0x0000000079E29000 000030 (v02 00000000 00000000) [ 0.000000] ACPI: DBG2 0x0000000079E28000 000072 (v00 INTEL EDK2 00000003 BRXT 0100000D) [ 0.000000] ACPI: DBGP 0x0000000079E27000 000034 (v01 INTEL EDK2 00000003 BRXT 0100000D) [ 0.000000] ACPI: HPET 0x0000000079E24000 000038 (v01 INTEL EDK2 00000003 BRXT 0100000D) [ 0.000000] ACPI: LPIT 0x0000000079E23000 00005C (v01 INTEL EDK2 00000003 BRXT 0100000D) [ 0.000000] ACPI: APIC 0x0000000079E22000 000084 (v03 INTEL EDK2 00000003 BRXT 0100000D) [ 0.000000] ACPI: MCFG 0x0000000079E21000 00003C (v01 INTEL EDK2 00000003 BRXT 0100000D) [ 0.000000] ACPI: NPKT 0x0000000079E20000 000065 (v01 INTEL EDK2 00000003 BRXT 0100000D) [ 0.000000] ACPI: WSMT 0x0000000079E1F000 000028 (v00 INTEL EDK2 00000003 BRXT 0100000D) [ 0.000000] ACPI: SSDT 0x0000000079E0B000 0046C3 (v02 INTEL RVPRtd3 00000003 BRXT 0100000D) [ 0.000000] ACPI: SSDT 0x0000000079E0A000 000B53 (v02 INTEL UsbCTabl 00000003 BRXT 0100000D) [ 0.000000] ACPI: SSDT 0x0000000079E08000 0016BE (v01 Intel_ Platform 00001000 INTL 20150818) [ 0.000000] ACPI: SSDT 0x0000000079E07000 000400 (v02 PmRef Cpu0Ist 00003000 INTL 20150818) [ 0.000000] ACPI: SSDT 0x0000000079E06000 00072B (v02 CpuRef CpuSsdt 00003000 INTL 20150818) [ 0.000000] ACPI: SSDT 0x0000000079E05000 000356 (v02 PmRef Cpu0Tst 00003000 INTL 20150818) [ 0.000000] ACPI: SSDT 0x0000000079E2C000 00017C (v02 PmRef ApTst 00003000 INTL 20150818) [ 0.000000] ACPI: SSDT 0x0000000079E01000 00277A (v02 SaSsdt SaSsdt 00003000 INTL 20150818) [ 0.000000] ACPI: FPDT 0x0000000079E00000 000044 (v01 INTEL EDK2 00000002 BRXT 01000013) [ 0.000000] ACPI: WDAT 0x0000000079E26000 000104 (v01 00000000 00000000) [ 0.000000] ACPI: NHLT 0x0000000079E13000 001A50 (v00 INTEL EDK2 00000002 BRXT 01000013) [ 0.000000] ACPI: Local APIC address 0xfee00000 [ 0.000000] No NUMA configuration found [ 0.000000] Faking a node at [mem 0x0000000000000000-0x000000047fffffff] [ 0.000000] NODE_DATA(0) allocated [mem 0x47fbfa000-0x47fbfdfff] [ 0.000000] Zone ranges: [ 0.000000] DMA [mem 0x0000000000001000-0x0000000000ffffff] [ 0.000000] DMA32 [mem 0x0000000001000000-0x00000000ffffffff] [ 0.000000] Normal [mem 0x0000000100000000-0x000000047fffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000000001000-0x0000000000057fff] [ 0.000000] node 0: [mem 0x0000000000059000-0x000000000009dfff] [ 0.000000] node 0: [mem 0x0000000000100000-0x000000000effffff] [ 0.000000] node 0: [mem 0x0000000012152000-0x0000000077fddfff] [ 0.000000] node 0: [mem 0x0000000079e2e000-0x000000007ac26fff] [ 0.000000] node 0: [mem 0x000000007ac52000-0x000000007affffff] [ 0.000000] node 0: [mem 0x0000000100000000-0x000000047fffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000000001000-0x000000047fffffff] [ 0.000000] On node 0 totalpages: 4153295 [ 0.000000] DMA zone: 64 pages used for memmap [ 0.000000] DMA zone: 21 pages reserved [ 0.000000] DMA zone: 3996 pages, LIFO batch:0 [ 0.000000] DMA32 zone: 7489 pages used for memmap [ 0.000000] DMA32 zone: 479283 pages, LIFO batch:31 [ 0.000000] Normal zone: 57344 pages used for memmap [ 0.000000] Normal zone: 3670016 pages, LIFO batch:31 [ 0.000000] Reserving Intel graphics memory at 0x000000007c000000-0x000000007fffffff [ 0.000000] ACPI: PM-Timer IO Port: 0x408 [ 0.000000] ACPI: Local APIC address 0xfee00000 [ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x01] high level lint[0x1]) [ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x02] high level lint[0x1]) [ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x03] high level lint[0x1]) [ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x04] high level lint[0x1]) [ 0.000000] IOAPIC[0]: apic_id 1, version 32, address 0xfec00000, GSI 0-119 [ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl) [ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 low level) [ 0.000000] ACPI: IRQ0 used by override. [ 0.000000] ACPI: IRQ9 used by override. [ 0.000000] Using ACPI (MADT) for SMP configuration information [ 0.000000] ACPI: HPET id: 0x8086a701 base: 0xfed00000 [ 0.000000] smpboot: Allowing 4 CPUs, 0 hotplug CPUs [ 0.000000] PM: Registered nosave memory: [mem 0x00000000-0x00000fff] [ 0.000000] PM: Registered nosave memory: [mem 0x00058000-0x00058fff] [ 0.000000] PM: Registered nosave memory: [mem 0x0009e000-0x000fffff] [ 0.000000] PM: Registered nosave memory: [mem 0x0f000000-0x12151fff] [ 0.000000] PM: Registered nosave memory: [mem 0x77fde000-0x79d8dfff] [ 0.000000] PM: Registered nosave memory: [mem 0x79d8e000-0x79dedfff] [ 0.000000] PM: Registered nosave memory: [mem 0x79dee000-0x79e2dfff] [ 0.000000] PM: Registered nosave memory: [mem 0x7ac27000-0x7ac27fff] [ 0.000000] PM: Registered nosave memory: [mem 0x7ac28000-0x7ac51fff] [ 0.000000] PM: Registered nosave memory: [mem 0x7b000000-0x7fffffff] [ 0.000000] PM: Registered nosave memory: [mem 0x80000000-0xdfffffff] [ 0.000000] PM: Registered nosave memory: [mem 0xe0000000-0xe3ffffff] [ 0.000000] PM: Registered nosave memory: [mem 0xe4000000-0xfed00fff] [ 0.000000] PM: Registered nosave memory: [mem 0xfed01000-0xfed01fff] [ 0.000000] PM: Registered nosave memory: [mem 0xfed02000-0xffffffff] [ 0.000000] e820: [mem 0x80000000-0xdfffffff] available for PCI devices [ 0.000000] Booting paravirtualized kernel on bare hardware [ 0.000000] clocksource: refined-jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645519600211568 ns [ 0.000000] setup_percpu: NR_CPUS:256 nr_cpumask_bits:256 nr_cpu_ids:4 nr_node_ids:1 [ 0.000000] percpu: Embedded 35 pages/cpu @ffff88047f800000 s103704 r8192 d31464 u524288 [ 0.000000] pcpu-alloc: s103704 r8192 d31464 u524288 alloc=1*2097152 [ 0.000000] pcpu-alloc: [0] 0 1 2 3 [ 0.000000] Built 1 zonelists in Node order, mobility grouping on. Total pages: 4088377 [ 0.000000] Policy zone: Normal [ 0.000000] Kernel command line: vmlinuz root=/dev/sda2 initrd=initrd.img idle=halt log_buf_len=4M i915.enable_rc6=1 i915.preliminary_hw_support=1 drm.debug=0xe i915.enable_guc_submission=1 [ 0.000000] PID hash table entries: 4096 (order: 3, 32768 bytes) [ 0.000000] Calgary: detecting Calgary via BIOS EBDA area [ 0.000000] Calgary: Unable to locate Rio Grande table in EBDA - bailing! [ 0.000000] Memory: 16178120K/16613180K available (8205K kernel code, 1367K rwdata, 3736K rodata, 1528K init, 1400K bss, 435060K reserved, 0K cma-reserved) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 [ 0.000000] Hierarchical RCU implementation. [ 0.000000] Build-time adjustment of leaf fanout to 64. [ 0.000000] RCU restricting CPUs from NR_CPUS=256 to nr_cpu_ids=4. [ 0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=64, nr_cpu_ids=4 [ 0.000000] NR_IRQS:16640 nr_irqs:1024 16 [ 0.000000] Console: colour dummy device 80x25 [ 0.000000] console [tty0] enabled [ 0.000000] clocksource: hpet: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 99544814920 ns [ 0.000000] hpet clockevent registered [ 0.000000] tsc: Fast TSC calibration using PIT [ 0.000000] tsc: Detected 4574.325 MHz processor [ 0.000025] Calibrating delay loop (skipped), value calculated using timer frequency.. 9148.65 BogoMIPS (lpj=18297300) [ 0.000029] pid_max: default: 32768 minimum: 301 [ 0.000034] ACPI: Core revision 20160422 [ 0.000309] Security Framework initialized [ 0.000312] Yama: becoming mindful. [ 0.000317] AppArmor: AppArmor initialized [ 0.000892] Dentry cache hash table entries: 2097152 (order: 12, 16777216 bytes) [ 0.003188] Inode-cache hash table entries: 1048576 (order: 11, 8388608 bytes) [ 0.004230] Mount-cache hash table entries: 32768 (order: 6, 262144 bytes) [ 0.004242] Mountpoint-cache hash table entries: 32768 (order: 6, 262144 bytes) [ 0.004414] CPU: Physical Processor ID: 0 [ 0.004417] CPU: Processor Core ID: 0 [ 0.004425] mce: CPU supports 7 MCE banks [ 0.004436] CPU0: Thermal monitoring enabled (TM1) [ 0.004461] Last level iTLB entries: 4KB 48, 2MB 0, 4MB 0 [ 0.004464] Last level dTLB entries: 4KB 0, 2MB 0, 4MB 0, 1GB 0 [ 0.005220] Freeing SMP alternatives memory: 32K (ffffffff820d5000 - ffffffff820dd000) [ 0.009231] ftrace: allocating 32251 entries in 126 pages [ 0.026495] smpboot: Max logical packages: 1 [ 0.026499] smpboot: APIC(0) Converting physical 0 to logical package 0 [ 0.026828] x2apic: IRQ remapping doesn't support X2APIC mode [ 0.028145] ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1 [ 0.067833] TSC deadline timer enabled [ 0.067836] smpboot: CPU0: Intel 06/5c (family: 0x6, model: 0x5c, stepping: 0x9) [ 0.067841] Performance Events: PEBS fmt3+, 32-deep LBR, Goldmont events, full-width counters, Intel PMU driver. [ 0.067852] ... version: 4 [ 0.067853] ... bit width: 48 [ 0.067855] ... generic registers: 4 [ 0.067857] ... value mask: 0000ffffffffffff [ 0.067859] ... max period: 0000ffffffffffff [ 0.067861] ... fixed-purpose events: 3 [ 0.067862] ... event mask: 000000070000000f [ 0.068276] NMI watchdog: enabled on all CPUs, permanently consumes one hw-PMU counter. [ 0.068351] x86: Booting SMP configuration: [ 0.068354] .... node #0, CPUs: #1 #2 #3 [ 0.309933] x86: Booted up 1 node, 4 CPUs [ 0.309937] smpboot: Total of 4 processors activated (36601.87 BogoMIPS) [ 0.310927] devtmpfs: initialized [ 0.310968] x86/mm: Memory block size: 128MB [ 0.313315] evm: security.selinux [ 0.313318] evm: security.SMACK64 [ 0.313320] evm: security.SMACK64EXEC [ 0.313321] evm: security.SMACK64TRANSMUTE [ 0.313323] evm: security.SMACK64MMAP [ 0.313325] evm: security.ima [ 0.313326] evm: security.capability [ 0.313387] PM: Registering ACPI NVS region [mem 0x79d8e000-0x79dedfff] (393216 bytes) [ 0.313394] PM: Registering ACPI NVS region [mem 0x7ac27000-0x7ac27fff] (4096 bytes) [ 0.313430] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns [ 0.313457] pinctrl core: initialized pinctrl subsystem [ 0.313542] RTC time: 21:35:02, date: 07/05/16 [ 0.314223] NET: Registered protocol family 16 [ 0.323908] cpuidle: using governor ladder [ 0.335912] cpuidle: using governor menu [ 0.335915] PCCT header not found. [ 0.335992] ACPI: bus type PCI registered [ 0.335995] acpiphp: ACPI Hot Plug PCI Controller Driver version: 0.5 [ 0.336035] PCI: MMCONFIG for domain 0000 [bus 00-3f] at [mem 0xe0000000-0xe3ffffff] (base 0xe0000000) [ 0.336040] PCI: MMCONFIG at [mem 0xe0000000-0xe3ffffff] reserved in E820 [ 0.336045] PCI: Using configuration type 1 for base access [ 0.348026] HugeTLB registered 1 GB page size, pre-allocated 0 pages [ 0.348030] HugeTLB registered 2 MB page size, pre-allocated 0 pages [ 0.348207] ACPI: Added _OSI(Module Device) [ 0.348209] ACPI: Added _OSI(Processor Device) [ 0.348211] ACPI: Added _OSI(3.0 _SCP Extensions) [ 0.348213] ACPI: Added _OSI(Processor Aggregator Device) [ 0.351423] ACPI: Executed 3 blocks of module-level executable AML code [ 0.352953] ACPI: Executed 2 blocks of module-level executable AML code [ 0.353795] ACPI: Executed 1 blocks of module-level executable AML code [ 0.355929] ACPI: 10 ACPI AML tables successfully acquired and loaded [ 0.359869] ACPI: Dynamic OEM Table Load: [ 0.359876] ACPI: SSDT 0xFFFF88046CD49E00 000102 (v02 PmRef Cpu0Cst 00003001 INTL 20150818) [ 0.360371] ACPI: Dynamic OEM Table Load: [ 0.360377] ACPI: SSDT 0xFFFF88046CE2E000 00015F (v02 PmRef ApIst 00003000 INTL 20150818) [ 0.360782] ACPI: Dynamic OEM Table Load: [ 0.360788] ACPI: SSDT 0xFFFF88046CD5B6C0 00008D (v02 PmRef ApCst 00003000 INTL 20150818) [ 0.361596] ACPI : EC: EC started [ 0.592105] ACPI: Interpreter enabled [ 0.592121] ACPI: (supports S0 S3 S4 S5) [ 0.592123] ACPI: Using IOAPIC for interrupt routing [ 0.592144] PCI: Using host bridge windows from ACPI; if necessary, use "pci=nocrs" and report a bug [ 0.593152] ACPI: Power Resource [PXP] (off) [ 0.593494] ACPI: Power Resource [PXP] (on) [ 0.612306] ACPI: Power Resource [PXP] (on) [ 0.632276] ACPI: Power Resource [PXP] (off) [ 0.632577] ACPI: Power Resource [PXP] (off) [ 0.632874] ACPI: Power Resource [PXP] (off) [ 0.633250] ACPI: Power Resource [SPPR] (on) [ 0.652145] ACPI: Power Resource [ODPR] (on) [ 0.652236] ACPI: Power Resource [SPPR] (off) [ 0.652414] ACPI: Power Resource [ODPR] (on) [ 0.652591] ACPI: Power Resource [UPPR] (on) [ 0.652735] ACPI: Power Resource [PX03] (on) [ 0.652976] ACPI: Power Resource [UPPR] (on) [ 0.653108] ACPI: Power Resource [UPPR] (on) [ 0.653344] ACPI: Power Resource [UPPR] (on) [ 0.653493] ACPI: Power Resource [UPPR] (on) [ 0.653623] ACPI: Power Resource [UPPR] (on) [ 0.653771] ACPI: Power Resource [USBC] (on) [ 0.653844] ACPI: Power Resource [SDPR] (on) [ 0.668251] ACPI: Power Resource [LSPR] (on) [ 0.669816] ACPI: Power Resource [PAUD] (on) [ 0.671598] ACPI: Power Resource [FN00] (on) [ 0.756410] ACPI: PCI Root Bridge [PCI0] (domain 0000 [bus 00-ff]) [ 0.756415] acpi PNP0A08:00: _OSC: OS supports [ExtendedConfig ASPM ClockPM Segments MSI] [ 0.756855] acpi PNP0A08:00: _OSC: OS now controls [PCIeHotplug PME AER PCIeCapability] [ 0.756865] acpi PNP0A08:00: [Firmware Info]: MMCONFIG for domain 0000 [bus 00-3f] only partially covers this bridge [ 0.757235] PCI host bridge to bus 0000:00 [ 0.757239] pci_bus 0000:00: root bus resource [io 0x0070-0x0077] [ 0.757241] pci_bus 0000:00: root bus resource [io 0x0000-0x006f window] [ 0.757243] pci_bus 0000:00: root bus resource [io 0x0078-0x0cf7 window] [ 0.757246] pci_bus 0000:00: root bus resource [io 0x0d00-0xffff window] [ 0.757248] pci_bus 0000:00: root bus resource [mem 0x7c000001-0x7fffffff window] [ 0.757251] pci_bus 0000:00: root bus resource [mem 0x7b800001-0x7bffffff window] [ 0.757255] pci_bus 0000:00: root bus resource [mem 0x80000000-0xcfffffff window] [ 0.757258] pci_bus 0000:00: root bus resource [mem 0xe0000000-0xefffffff window] [ 0.757261] pci_bus 0000:00: root bus resource [bus 00-ff] [ 0.757268] pci 0000:00:00.0: [8086:5af0] type 00 class 0x060000 [ 0.757416] pci 0000:00:02.0: [8086:5a84] type 00 class 0x030000 [ 0.757422] pci 0000:00:02.0: reg 0x10: [mem 0x90000000-0x90ffffff 64bit] [ 0.757426] pci 0000:00:02.0: reg 0x18: [mem 0x80000000-0x8fffffff 64bit pref] [ 0.757429] pci 0000:00:02.0: reg 0x20: [io 0x2000-0x203f] [ 0.757575] pci 0000:00:03.0: [8086:5a88] type 00 class 0x048000 [ 0.757581] pci 0000:00:03.0: reg 0x10: [mem 0x91000000-0x91ffffff 64bit] [ 0.757721] pci 0000:00:0e.0: [8086:5a98] type 00 class 0x040300 [ 0.757729] pci 0000:00:0e.0: reg 0x10: [mem 0x92310000-0x92313fff 64bit] [ 0.757739] pci 0000:00:0e.0: reg 0x20: [mem 0x92000000-0x920fffff 64bit] [ 0.757767] pci 0000:00:0e.0: PME# supported from D0 D3hot D3cold [ 0.757897] pci 0000:00:0e.0: System wakeup disabled by ACPI [ 0.757927] pci 0000:00:0f.0: [8086:5a9a] type 00 class 0x078000 [ 0.757938] pci 0000:00:0f.0: reg 0x10: [mem 0x92318000-0x92318fff 64bit] [ 0.757979] pci 0000:00:0f.0: PME# supported from D3hot [ 0.758103] pci 0000:00:11.0: [8086:5aa2] type 00 class 0x005007 [ 0.758113] pci 0000:00:11.0: reg 0x10: [mem 0x92314000-0x92315fff 64bit] [ 0.758120] pci 0000:00:11.0: reg 0x18: [mem 0x9231b000-0x9231bfff 64bit] [ 0.758273] pci 0000:00:12.0: [8086:5ae3] type 00 class 0x010601 [ 0.758280] pci 0000:00:12.0: reg 0x10: [mem 0x92316000-0x92317fff] [ 0.758284] pci 0000:00:12.0: reg 0x14: [mem 0x92342000-0x923420ff] [ 0.758287] pci 0000:00:12.0: reg 0x18: [io 0x2080-0x2087] [ 0.758291] pci 0000:00:12.0: reg 0x1c: [io 0x2088-0x208b] [ 0.758294] pci 0000:00:12.0: reg 0x20: [io 0x2060-0x207f] [ 0.758298] pci 0000:00:12.0: reg 0x24: [mem 0x92340000-0x923407ff] [ 0.758315] pci 0000:00:12.0: PME# supported from D3hot [ 0.758448] pci 0000:00:13.0: [8086:5ada] type 01 class 0x060400 [ 0.758478] pci 0000:00:13.0: PME# supported from D0 D3hot D3cold [ 0.758610] pci 0000:00:13.0: System wakeup disabled by ACPI [ 0.758647] pci 0000:00:14.0: [8086:5ad7] type 01 class 0x060400 [ 0.758686] pci 0000:00:14.0: PME# supported from D0 D3hot D3cold [ 0.758823] pci 0000:00:14.0: System wakeup disabled by ACPI [ 0.758857] pci 0000:00:15.0: [8086:5aa8] type 00 class 0x0c0330 [ 0.758866] pci 0000:00:15.0: reg 0x10: [mem 0x92300000-0x9230ffff 64bit] [ 0.758897] pci 0000:00:15.0: PME# supported from D3hot D3cold [ 0.759000] pci 0000:00:15.0: System wakeup disabled by ACPI [ 0.759035] pci 0000:00:16.0: [8086:5aac] type 00 class 0x118000 [ 0.759045] pci 0000:00:16.0: reg 0x10: [mem 0x9231c000-0x9231cfff 64bit] [ 0.759050] pci 0000:00:16.0: reg 0x18: [mem 0x9231d000-0x9231dfff 64bit] [ 0.759196] pci 0000:00:16.1: [8086:5aae] type 00 class 0x118000 [ 0.759205] pci 0000:00:16.1: reg 0x10: [mem 0x9231e000-0x9231efff 64bit] [ 0.759211] pci 0000:00:16.1: reg 0x18: [mem 0x9231f000-0x9231ffff 64bit] [ 0.759350] pci 0000:00:16.2: [8086:5ab0] type 00 class 0x118000 [ 0.759359] pci 0000:00:16.2: reg 0x10: [mem 0x92320000-0x92320fff 64bit] [ 0.759365] pci 0000:00:16.2: reg 0x18: [mem 0x92321000-0x92321fff 64bit] [ 0.759507] pci 0000:00:16.3: [8086:5ab2] type 00 class 0x118000 [ 0.759516] pci 0000:00:16.3: reg 0x10: [mem 0x92322000-0x92322fff 64bit] [ 0.759522] pci 0000:00:16.3: reg 0x18: [mem 0x92323000-0x92323fff 64bit] [ 0.759665] pci 0000:00:17.0: [8086:5ab4] type 00 class 0x118000 [ 0.759675] pci 0000:00:17.0: reg 0x10: [mem 0x92324000-0x92324fff 64bit] [ 0.759680] pci 0000:00:17.0: reg 0x18: [mem 0x92325000-0x92325fff 64bit] [ 0.759821] pci 0000:00:17.1: [8086:5ab6] type 00 class 0x118000 [ 0.759830] pci 0000:00:17.1: reg 0x10: [mem 0x92326000-0x92326fff 64bit] [ 0.759836] pci 0000:00:17.1: reg 0x18: [mem 0x92327000-0x92327fff 64bit] [ 0.759973] pci 0000:00:17.2: [8086:5ab8] type 00 class 0x118000 [ 0.759983] pci 0000:00:17.2: reg 0x10: [mem 0x92328000-0x92328fff 64bit] [ 0.759989] pci 0000:00:17.2: reg 0x18: [mem 0x92329000-0x92329fff 64bit] [ 0.760134] pci 0000:00:17.3: [8086:5aba] type 00 class 0x118000 [ 0.760143] pci 0000:00:17.3: reg 0x10: [mem 0x9232a000-0x9232afff 64bit] [ 0.760149] pci 0000:00:17.3: reg 0x18: [mem 0x9232b000-0x9232bfff 64bit] [ 0.760291] pci 0000:00:18.0: [8086:5abc] type 00 class 0x118000 [ 0.760301] pci 0000:00:18.0: reg 0x10: [mem 0x9232c000-0x9232cfff 64bit] [ 0.760306] pci 0000:00:18.0: reg 0x18: [mem 0x9232d000-0x9232dfff 64bit] [ 0.760448] pci 0000:00:18.1: [8086:5abe] type 00 class 0x118000 [ 0.760457] pci 0000:00:18.1: reg 0x10: [mem 0x9232e000-0x9232efff 64bit] [ 0.760463] pci 0000:00:18.1: reg 0x18: [mem 0x9232f000-0x9232ffff 64bit] [ 0.760602] pci 0000:00:18.2: [8086:5ac0] type 00 class 0x118000 [ 0.760615] pci 0000:00:18.2: reg 0x10: [mem 0x92330000-0x92330fff 64bit] [ 0.760620] pci 0000:00:18.2: reg 0x18: [mem 0x92331000-0x92331fff 64bit] [ 0.760759] pci 0000:00:18.3: [8086:5aee] type 00 class 0x118000 [ 0.760768] pci 0000:00:18.3: reg 0x10: [mem 0x92332000-0x92332fff 64bit] [ 0.760774] pci 0000:00:18.3: reg 0x18: [mem 0x92333000-0x92333fff 64bit] [ 0.760916] pci 0000:00:19.0: [8086:5ac2] type 00 class 0x118000 [ 0.760925] pci 0000:00:19.0: reg 0x10: [mem 0x92334000-0x92334fff 64bit] [ 0.760931] pci 0000:00:19.0: reg 0x18: [mem 0x92335000-0x92335fff 64bit] [ 0.761072] pci 0000:00:19.1: [8086:5ac4] type 00 class 0x118000 [ 0.761081] pci 0000:00:19.1: reg 0x10: [mem 0x92336000-0x92336fff 64bit] [ 0.761087] pci 0000:00:19.1: reg 0x18: [mem 0x92337000-0x92337fff 64bit] [ 0.761225] pci 0000:00:19.2: [8086:5ac6] type 00 class 0x118000 [ 0.761235] pci 0000:00:19.2: reg 0x10: [mem 0x92338000-0x92338fff 64bit] [ 0.761241] pci 0000:00:19.2: reg 0x18: [mem 0x92339000-0x92339fff 64bit] [ 0.761389] pci 0000:00:1b.0: [8086:5aca] type 00 class 0x080501 [ 0.761397] pci 0000:00:1b.0: reg 0x10: [mem 0x9233a000-0x9233afff 64bit] [ 0.761402] pci 0000:00:1b.0: reg 0x18: [mem 0x9233b000-0x9233bfff 64bit] [ 0.761549] pci 0000:00:1c.0: [8086:5acc] type 00 class 0x080501 [ 0.761557] pci 0000:00:1c.0: reg 0x10: [mem 0x9233c000-0x9233cfff 64bit] [ 0.761566] pci 0000:00:1c.0: reg 0x18: [mem 0x9233d000-0x9233dfff 64bit] [ 0.761712] pci 0000:00:1e.0: [8086:5ad0] type 00 class 0x080501 [ 0.761720] pci 0000:00:1e.0: reg 0x10: [mem 0x9233e000-0x9233efff 64bit] [ 0.761725] pci 0000:00:1e.0: reg 0x18: [mem 0x9233f000-0x9233ffff 64bit] [ 0.761867] pci 0000:00:1f.0: [8086:5ae8] type 00 class 0x060100 [ 0.762025] pci 0000:00:1f.1: [8086:5ad4] type 00 class 0x0c0500 [ 0.762040] pci 0000:00:1f.1: reg 0x10: [mem 0x92341000-0x923410ff 64bit] [ 0.762063] pci 0000:00:1f.1: reg 0x20: [io 0x2040-0x205f] [ 0.762243] pci 0000:01:00.0: [8086:1539] type 00 class 0x020000 [ 0.762259] pci 0000:01:00.0: reg 0x10: [mem 0x92200000-0x9221ffff] [ 0.762269] pci 0000:01:00.0: reg 0x18: [io 0x1000-0x101f] [ 0.762276] pci 0000:01:00.0: reg 0x1c: [mem 0x92220000-0x92223fff] [ 0.762332] pci 0000:01:00.0: PME# supported from D0 D3hot D3cold [ 0.762353] pci 0000:01:00.0: System wakeup disabled by ACPI [ 0.768146] pci 0000:00:13.0: PCI bridge to [bus 01] [ 0.768149] pci 0000:00:13.0: bridge window [io 0x1000-0x1fff] [ 0.768151] pci 0000:00:13.0: bridge window [mem 0x92200000-0x922fffff] [ 0.768296] pci 0000:02:00.0: [8086:095a] type 00 class 0x028000 [ 0.768360] pci 0000:02:00.0: reg 0x10: [mem 0x92100000-0x92101fff 64bit] [ 0.768451] pci 0000:02:00.0: can't set Max Payload Size to 256; if necessary, use "pci=pcie_bus_safe" and report a bug [ 0.768544] pci 0000:02:00.0: PME# supported from D0 D3hot D3cold [ 0.768667] pci 0000:02:00.0: System wakeup disabled by ACPI [ 0.776246] pci 0000:00:14.0: PCI bridge to [bus 02] [ 0.776255] pci 0000:00:14.0: bridge window [mem 0x92100000-0x921fffff] [ 0.777645] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 10 11 12 14 *15), disabled. [ 0.777685] ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 10 11 12 14 *15), disabled. [ 0.777724] ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 10 11 12 14 *15), disabled. [ 0.777764] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 10 11 12 14 *15), disabled. [ 0.777803] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 10 11 12 14 *15), disabled. [ 0.777842] ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 10 11 12 14 *15), disabled. [ 0.777880] ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 10 11 12 14 *15), disabled. [ 0.777920] ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 10 11 12 14 *15), disabled. [ 0.778375] ACPI: Enabled 2 GPEs in block 00 to 7F [ 0.778389] ACPI : EC: EC stopped [ 0.778440] ACPI : EC: GPE = 0x2b, I/O: command/status = 0x66, data = 0x62 [ 0.778443] ACPI : EC: EC started [ 1.008375] vgaarb: setting as boot device: PCI:0000:00:02.0 [ 1.008380] vgaarb: device added: PCI:0000:00:02.0,decodes=io+mem,owns=io+mem,locks=none [ 1.008385] vgaarb: loaded [ 1.008387] vgaarb: bridge control possible 0000:00:02.0 [ 1.008503] SCSI subsystem initialized [ 1.008536] libata version 3.00 loaded. [ 1.008551] ACPI: bus type USB registered [ 1.008564] usbcore: registered new interface driver usbfs [ 1.008571] usbcore: registered new interface driver hub [ 1.008584] usbcore: registered new device driver usb [ 1.008683] PCI: Using ACPI for IRQ routing [ 1.010463] PCI: pci_cache_line_size set to 64 bytes [ 1.010598] e820: reserve RAM buffer [mem 0x00058000-0x0005ffff] [ 1.010599] e820: reserve RAM buffer [mem 0x0009e000-0x0009ffff] [ 1.010600] e820: reserve RAM buffer [mem 0x0f000000-0x0fffffff] [ 1.010601] e820: reserve RAM buffer [mem 0x77fde000-0x77ffffff] [ 1.010602] e820: reserve RAM buffer [mem 0x7ac27000-0x7bffffff] [ 1.010603] e820: reserve RAM buffer [mem 0x7b000000-0x7bffffff] [ 1.010665] NetLabel: Initializing [ 1.010667] NetLabel: domain hash size = 128 [ 1.010669] NetLabel: protocols = UNLABELED CIPSOv4 [ 1.010677] NetLabel: unlabeled traffic allowed by default [ 1.010774] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0, 0, 0, 0, 0, 0 [ 1.010780] hpet0: 8 comparators, 64-bit 19.200000 MHz counter [ 1.011279] clocksource: Switched to clocksource hpet [ 1.014889] VFS: Disk quotas dquot_6.6.0 [ 1.014903] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes) [ 1.014944] AppArmor: AppArmor Filesystem Enabled [ 1.014976] pnp: PnP ACPI init [ 1.015068] system 00:00: [io 0x06a4] has been reserved [ 1.015071] system 00:00: [io 0x06a0] has been reserved [ 1.015075] system 00:00: Plug and Play ACPI device, IDs PNP0c02 (active) [ 1.015139] pnp 00:01: disabling [io 0x164e-0x164f] because it overlaps 0000:00:13.0 BAR 13 [io 0x1000-0x1fff] [ 1.015162] system 00:01: [io 0x0680-0x069f] has been reserved [ 1.015165] system 00:01: [io 0x0400-0x047f] has been reserved [ 1.015167] system 00:01: [io 0x0500-0x05fe] has been reserved [ 1.015169] system 00:01: [io 0x0600-0x061f] has been reserved [ 1.015173] system 00:01: Plug and Play ACPI device, IDs PNP0c02 (active) [ 1.015212] pnp 00:02: Plug and Play ACPI device, IDs PNP0303 (active) [ 1.015479] system 00:03: [mem 0xe0000000-0xefffffff] could not be reserved [ 1.015482] system 00:03: [mem 0xfea00000-0xfeafffff] has been reserved [ 1.015484] system 00:03: [mem 0xfed01000-0xfed01fff] has been reserved [ 1.015487] system 00:03: [mem 0xfed03000-0xfed03fff] has been reserved [ 1.015489] system 00:03: [mem 0xfed06000-0xfed06fff] has been reserved [ 1.015492] system 00:03: [mem 0xfed08000-0xfed09fff] has been reserved [ 1.015494] system 00:03: [mem 0xfed80000-0xfedbffff] has been reserved [ 1.015497] system 00:03: [mem 0xfed1c000-0xfed1cfff] has been reserved [ 1.015499] system 00:03: [mem 0xfee00000-0xfeefffff] has been reserved [ 1.015503] system 00:03: Plug and Play ACPI device, IDs PNP0c02 (active) [ 1.015622] pnp 00:04: Plug and Play ACPI device, IDs PNP0b00 (active) [ 1.015706] pnp: PnP ACPI: found 5 devices [ 1.022189] clocksource: acpi_pm: mask: 0xffffff max_cycles: 0xffffff, max_idle_ns: 2085701024 ns [ 1.022209] pci 0000:00:13.0: PCI bridge to [bus 01] [ 1.022213] pci 0000:00:13.0: bridge window [io 0x1000-0x1fff] [ 1.022216] pci 0000:00:13.0: bridge window [mem 0x92200000-0x922fffff] [ 1.022221] pci 0000:00:14.0: PCI bridge to [bus 02] [ 1.022230] pci 0000:00:14.0: bridge window [mem 0x92100000-0x921fffff] [ 1.022240] pci_bus 0000:00: resource 4 [io 0x0070-0x0077] [ 1.022241] pci_bus 0000:00: resource 5 [io 0x0000-0x006f window] [ 1.022242] pci_bus 0000:00: resource 6 [io 0x0078-0x0cf7 window] [ 1.022243] pci_bus 0000:00: resource 7 [io 0x0d00-0xffff window] [ 1.022244] pci_bus 0000:00: resource 8 [mem 0x7c000001-0x7fffffff window] [ 1.022245] pci_bus 0000:00: resource 9 [mem 0x7b800001-0x7bffffff window] [ 1.022246] pci_bus 0000:00: resource 10 [mem 0x80000000-0xcfffffff window] [ 1.022247] pci_bus 0000:00: resource 11 [mem 0xe0000000-0xefffffff window] [ 1.022248] pci_bus 0000:01: resource 0 [io 0x1000-0x1fff] [ 1.022249] pci_bus 0000:01: resource 1 [mem 0x92200000-0x922fffff] [ 1.022251] pci_bus 0000:02: resource 1 [mem 0x92100000-0x921fffff] [ 1.022265] NET: Registered protocol family 2 [ 1.022380] TCP established hash table entries: 131072 (order: 8, 1048576 bytes) [ 1.022611] TCP bind hash table entries: 65536 (order: 8, 1048576 bytes) [ 1.022781] TCP: Hash tables configured (established 131072 bind 65536) [ 1.022807] UDP hash table entries: 8192 (order: 6, 262144 bytes) [ 1.022878] UDP-Lite hash table entries: 8192 (order: 6, 262144 bytes) [ 1.022964] NET: Registered protocol family 1 [ 1.022975] pci 0000:00:02.0: Video device with shadowed ROM at [mem 0x000c0000-0x000dffff] [ 1.023176] PCI: CLS 64 bytes, default 64 [ 1.023206] Trying to unpack rootfs image as initramfs... [ 1.405679] Freeing initrd memory: 38192K (ffff8800722a0000 - ffff8800747ec000) [ 1.405684] PCI-DMA: Using software bounce buffering for IO (SWIOTLB) [ 1.405687] software IO TLB [mem 0x6e2a0000-0x722a0000] (64MB) mapped at [ffff88006e2a0000-ffff88007229ffff] [ 1.405779] Scanning for low memory corruption every 60 seconds [ 1.405988] futex hash table entries: 1024 (order: 4, 65536 bytes) [ 1.406000] audit: initializing netlink subsys (disabled) [ 1.406009] audit: type=2000 audit(1467754502.823:1): initialized [ 1.406202] Initialise system trusted keyrings [ 1.406269] workingset: timestamp_bits=38 max_order=22 bucket_order=0 [ 1.407334] zbud: loaded [ 1.407680] fuse init (API version 7.25) [ 1.407768] Key type big_key registered [ 1.408170] Key type asymmetric registered [ 1.408172] Asymmetric key parser 'x509' registered [ 1.408195] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 248) [ 1.408223] io scheduler noop registered [ 1.408225] io scheduler deadline registered (default) [ 1.408245] io scheduler cfq registered [ 1.408513] pcieport 0000:00:13.0: Signaling PME through PCIe PME interrupt [ 1.408516] pci 0000:01:00.0: Signaling PME through PCIe PME interrupt [ 1.408519] pcie_pme 0000:00:13.0:pcie001: service driver pcie_pme loaded [ 1.408533] pcieport 0000:00:14.0: Signaling PME through PCIe PME interrupt [ 1.408536] pci 0000:02:00.0: Signaling PME through PCIe PME interrupt [ 1.408542] pcie_pme 0000:00:14.0:pcie001: service driver pcie_pme loaded [ 1.408545] pci_hotplug: PCI Hot Plug PCI Core version: 0.5 [ 1.408550] pciehp: PCI Express Hot Plug Controller Driver version: 0.4 [ 1.408570] efifb: probing for efifb [ 1.408580] efifb: framebuffer at 0x80000000, using 8100k, total 8100k [ 1.408582] efifb: mode is 1920x1080x32, linelength=7680, pages=1 [ 1.408584] efifb: scrolling: redraw [ 1.408586] efifb: Truecolor: size=8:8:8:8, shift=24:16:8:0 [ 1.412198] Console: switching to colour frame buffer device 240x67 [ 1.415727] fb0: EFI VGA frame buffer device [ 1.415785] ACPI: AC Adapter [ADP1] (off-line) [ 1.415833] input: Lid Switch as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0A08:00/device:01/PNP0C09:00/PNP0C0D:00/input/input0 [ 1.415996] ACPI: Lid Switch [LID0] [ 1.416036] input: Power Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0C:00/input/input1 [ 1.416059] ACPI: Power Button [PWRB] [ 1.416093] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input2 [ 1.416116] ACPI: Power Button [PWRF] [ 1.419615] thermal LNXTHERM:00: registered as thermal_zone0 [ 1.419632] ACPI: Thermal Zone [TZ01] (31 C) [ 1.419662] GHES: HEST is not enabled! [ 1.419733] Serial: 8250/16550 driver, 32 ports, IRQ sharing enabled [ 1.419750] ACPI: Battery Slot [BAT0] (battery present) [ 1.419794] ACPI: Battery Slot [BAT1] (battery absent) [ 1.439819] serial8250: ttyS0 at I/O 0x3f8 (irq = 4, base_baud = 115200) is a 16550A [ 1.440908] Linux agpgart interface v0.103 [ 1.442870] brd: module loaded [ 1.443695] loop: module loaded [ 1.443827] libphy: Fixed MDIO Bus: probed [ 1.443842] tun: Universal TUN/TAP device driver, 1.6 [ 1.443856] tun: (C) 1999-2004 Max Krasnyansky [ 1.443901] PPP generic driver version 2.4.2 [ 1.443947] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 1.443970] ehci-pci: EHCI PCI platform driver [ 1.443988] ehci-platform: EHCI generic platform driver [ 1.444009] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 1.444031] ohci-pci: OHCI PCI platform driver [ 1.444048] ohci-platform: OHCI generic platform driver [ 1.444066] uhci_hcd: USB Universal Host Controller Interface driver [ 1.444178] xhci_hcd 0000:00:15.0: xHCI Host Controller [ 1.444196] xhci_hcd 0000:00:15.0: new USB bus registered, assigned bus number 1 [ 1.445256] xhci_hcd 0000:00:15.0: hcc params 0x200077c1 hci version 0x100 quirks 0x00009810 [ 1.445285] xhci_hcd 0000:00:15.0: cache line size of 64 is not supported [ 1.445330] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002 [ 1.445349] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 1.445368] usb usb1: Product: xHCI Host Controller [ 1.445382] usb usb1: Manufacturer: Linux 4.7.0-rc6-drm-intel-nightly-ww29-commit-e549c0b+ xhci-hcd [ 1.445409] usb usb1: SerialNumber: 0000:00:15.0 [ 1.445495] hub 1-0:1.0: USB hub found [ 1.445511] hub 1-0:1.0: 8 ports detected [ 1.445948] xhci_hcd 0000:00:15.0: xHCI Host Controller [ 1.445964] xhci_hcd 0000:00:15.0: new USB bus registered, assigned bus number 2 [ 1.446004] usb usb2: New USB device found, idVendor=1d6b, idProduct=0003 [ 1.446863] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 1.447723] usb usb2: Product: xHCI Host Controller [ 1.448577] usb usb2: Manufacturer: Linux 4.7.0-rc6-drm-intel-nightly-ww29-commit-e549c0b+ xhci-hcd [ 1.449445] usb usb2: SerialNumber: 0000:00:15.0 [ 1.450387] hub 2-0:1.0: USB hub found [ 1.451256] hub 2-0:1.0: 7 ports detected [ 1.452551] i8042: PNP: PS/2 Controller [PNP0303:PS2K] at 0x60,0x64 irq 1 [ 1.453437] i8042: PNP: PS/2 appears to have AUX port disabled, if this is incorrect please boot with i8042.nopnp [ 1.454633] i8042: Warning: Keylock active [ 1.455634] serio: i8042 KBD port at 0x60,0x64 irq 1 [ 1.456584] mousedev: PS/2 mouse device common for all mice [ 1.457611] rtc_cmos 00:04: RTC can wake from S4 [ 1.458630] rtc_cmos 00:04: rtc core: registered rtc_cmos as rtc0 [ 1.459542] rtc_cmos 00:04: alarms up to one month, y3k, 242 bytes nvram, hpet irqs [ 1.460440] i2c /dev entries driver [ 1.461366] device-mapper: uevent: version 1.0.3 [ 1.462295] device-mapper: ioctl: 4.34.0-ioctl (2015-10-28) initialised: dm-devel@redhat.com [ 1.463192] ledtrig-cpu: registered to indicate activity on CPUs [ 1.464090] EFI Variables Facility v0.08 2004-May-17 [ 1.468231] NET: Registered protocol family 10 [ 1.469256] NET: Registered protocol family 17 [ 1.470141] Key type dns_resolver registered [ 1.471160] microcode: CPU0 sig=0x506c9, pf=0x1, revision=0x12 [ 1.472052] microcode: CPU1 sig=0x506c9, pf=0x1, revision=0x12 [ 1.472935] microcode: CPU2 sig=0x506c9, pf=0x1, revision=0x12 [ 1.473801] microcode: CPU3 sig=0x506c9, pf=0x1, revision=0x12 [ 1.474672] microcode: Microcode Update Driver: v2.01 , Peter Oruba [ 1.475616] registered taskstats version 1 [ 1.476459] Loading compiled-in X.509 certificates [ 1.479103] Loaded X.509 cert 'Build time autogenerated kernel key: 04ebd577e75c703f7713f9a3a2992d532133e7de' [ 1.479977] zswap: loaded using pool lzo/zbud [ 1.482983] Key type trusted registered [ 1.486056] Key type encrypted registered [ 1.486875] AppArmor: AppArmor sha1 policy hashing enabled [ 1.487706] ima: No TPM chip found, activating TPM-bypass! [ 1.488550] evm: HMAC attrs: 0x1 [ 1.489717] Magic number: 8:638:600 [ 1.490628] rtc_cmos 00:04: setting system clock to 2016-07-05 21:35:07 UTC (1467754507) [ 1.491826] BIOS EDD facility v0.16 2004-Jun-25, 0 devices found [ 1.492673] EDD information not available. [ 1.493543] PM: Hibernation image not present or could not be loaded. [ 1.494192] Freeing unused kernel memory: 1528K (ffffffff81f57000 - ffffffff820d5000) [ 1.495034] Write protecting the kernel read-only data: 14336k [ 1.496213] Freeing unused kernel memory: 2020K (ffff880001807000 - ffff880001a00000) [ 1.497687] Freeing unused kernel memory: 360K (ffff880001da6000 - ffff880001e00000) [ 1.506930] random: systemd-udevd urandom read with 5 bits of entropy available [ 1.511968] atkbd serio0: Failed to deactivate keyboard on isa0060/serio0 [ 1.526760] usb 1-2: new high-speed USB device number 2 using xhci_hcd [ 1.549319] hidraw: raw HID events driver (C) Jiri Kosina [ 1.555170] [drm] Initialized drm 1.1.0 20060810 [ 1.556983] pps_core: LinuxPPS API ver. 1 registered [ 1.557874] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti [ 1.558906] sdhci: Secure Digital Host Controller Interface driver [ 1.559808] sdhci: Copyright(c) Pierre Ossman [ 1.561680] sdhci-pci 0000:00:1b.0: SDHCI controller found [8086:5aca] (rev a) [ 1.561990] PTP clock support registered [ 1.563575] sdhci-pci 0000:00:1b.0: failed to setup card detect gpio [ 1.564856] dca service started, version 1.12.1 [ 1.570462] igb: Intel(R) Gigabit Ethernet Network Driver - version 5.3.0-k [ 1.571374] igb: Copyright (c) 2007-2014 Intel Corporation. [ 1.573358] mmc0: SDHCI controller on PCI [0000:00:1b.0] using ADMA 64-bit [ 1.574331] atkbd serio0: Failed to enable keyboard on isa0060/serio0 [ 1.574432] ahci 0000:00:12.0: version 3.0 [ 1.575279] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input3 [ 1.578626] ahci 0000:00:12.0: AHCI 0001.0301 32 slots 1 ports 6 Gbps 0x1 impl SATA mode [ 1.579571] ahci 0000:00:12.0: flags: 64bit ncq sntf pm clo only pmp pio slum part deso sadm sds apst [ 1.580678] Setting dangerous option enable_rc6 - tainting kernel [ 1.581676] Setting dangerous option preliminary_hw_support - tainting kernel [ 1.582602] Setting dangerous option enable_guc_submission - tainting kernel [ 1.583654] scsi host0: ahci [ 1.584009] pps pps0: new PPS source ptp0 [ 1.584010] igb 0000:01:00.0: added PHC on eth0 [ 1.584011] igb 0000:01:00.0: Intel(R) Gigabit Ethernet Network Connection [ 1.584011] igb 0000:01:00.0: eth0: (PCIe:2.5Gb/s:Width x1) 90:49:fa:01:93:40 [ 1.584012] igb 0000:01:00.0: eth0: PBA No: FFFFFF-0FF [ 1.584013] igb 0000:01:00.0: Using MSI-X interrupts. 2 rx queue(s), 2 tx queue(s) [ 1.586448] usb 1-2: New USB device found, idVendor=05e3, idProduct=0608 [ 1.586449] usb 1-2: New USB device strings: Mfr=0, Product=1, SerialNumber=0 [ 1.586450] usb 1-2: Product: USB2.0 Hub [ 1.586678] hub 1-2:1.0: USB hub found [ 1.586876] hub 1-2:1.0: 4 ports detected [ 1.593338] igb 0000:01:00.0 enp1s0: renamed from eth0 [ 1.595544] ata1: SATA max UDMA/133 abar m2048@0x92340000 port 0x92340100 irq 128 [ 1.596458] sdhci-pci 0000:00:1c.0: SDHCI controller found [8086:5acc] (rev a) [ 1.601480] mmc1: SDHCI controller on PCI [0000:00:1c.0] using ADMA 64-bit [ 1.602378] sdhci-pci 0000:00:1e.0: SDHCI controller found [8086:5ad0] (rev a) [ 1.607396] mmc2: SDHCI controller on PCI [0000:00:1e.0] using ADMA 64-bit [ 1.614089] [drm:intel_detect_pch] No PCH found. [ 1.614092] [drm:get_allowed_dc_mask] Allowed DC state mask 09 [ 1.614102] [drm:intel_device_info_dump] i915 device info: gen=9, pciid=0x5a84 rev=0x0a flags=need_gfx_hws,is_broxton,has_fbc,has_hotplug,has_ddi,has_fpga_dbg, [ 1.614177] [drm:intel_device_info_runtime_init] slice total: 1 [ 1.614178] [drm:intel_device_info_runtime_init] subslice total: 3 [ 1.614178] [drm:intel_device_info_runtime_init] subslice per slice: 3 [ 1.614179] [drm:intel_device_info_runtime_init] EU total: 18 [ 1.614180] [drm:intel_device_info_runtime_init] EU per subslice: 6 [ 1.614180] [drm:intel_device_info_runtime_init] has slice power gating: n [ 1.614181] [drm:intel_device_info_runtime_init] has subslice power gating: y [ 1.614182] [drm:intel_device_info_runtime_init] has EU power gating: y [ 1.614183] [drm:intel_sanitize_options] ppgtt mode: 3 [ 1.614201] [drm:i915_gem_init_stolen] Memory reserved for graphics device: 65536K, usable: 64512K [ 1.614202] [drm] Memory usable by graphics device = 4096M [ 1.615120] [drm:i915_ggtt_init_hw] GMADR size = 256M [ 1.615121] [drm:i915_ggtt_init_hw] GTT stolen size = 64M [ 1.615122] checking generic (80000000 7e9000) vs hw (80000000 10000000) [ 1.615123] fb: switching to inteldrmfb from EFI VGA [ 1.617034] usb 1-7: new full-speed USB device number 3 using xhci_hcd [ 1.620991] Console: switching to colour dummy device 80x25 [ 1.621039] [drm] Replacing VGA console driver [ 1.621124] [drm:bxt_check_bios_rc6_setup] BIOS enabled RC states: HW_CTRL off HW_RC6 off SW_TARGET_STATE 4 [ 1.621151] [drm:intel_opregion_setup] graphic opregion physical addr: 0x79dd7018 [ 1.621156] [drm:intel_opregion_setup] Public ACPI methods supported [ 1.621157] [drm:intel_opregion_setup] ASLE supported [ 1.621159] [drm:intel_opregion_setup] Found valid VBT in ACPI OpRegion (RVDA) [ 1.621182] [drm] Supports vblank timestamp caching Rev 2 (21.10.2013). [ 1.621184] [drm] Driver supports precise vblank timestamp query. [ 1.621186] [drm:init_vbt_defaults] Set default to SSC at 100000 kHz [ 1.621187] [drm:intel_bios_init] VBT signature "$VBT BROXTON ", BDB version 207 [ 1.621189] [drm:parse_general_features] BDB_GENERAL_FEATURES int_tv_support 0 int_crt_support 0 lvds_use_ssc 0 lvds_ssc_freq 120000 display_clock_mode 1 fdi_rx_polarity_inverted 0 [ 1.621190] [drm:parse_general_definitions] crt_ddc_bus_pin: 2 [ 1.621191] [drm:intel_opregion_get_panel_type] Failed to get panel details from OpRegion (-19) [ 1.621192] [drm:parse_lfp_panel_data] Panel type: 2 (VBT) [ 1.621193] [drm:parse_lfp_panel_data] DRRS supported mode is seamless [ 1.621194] [drm:parse_lfp_panel_data] Found panel mode in BIOS VBT tables: [ 1.621196] [drm:drm_mode_debug_printmodeline] Modeline 0:"1024x768" 0 65000 1024 1048 1184 1344 768 771 777 806 0x8 0xa [ 1.621196] [drm:parse_lfp_panel_data] VBT initial LVDS value 300 [ 1.621197] [drm:parse_lfp_backlight] VBT backlight PWM modulation frequency 200 Hz, active high, min brightness 0, level 180 [ 1.621198] [drm:parse_sdvo_device_mapping] Unsupported child device size for SDVO mapping. [ 1.621199] [drm:parse_device_mapping] Expected child device config size for VBT version 207 not known; assuming 38 [ 1.621200] [drm:parse_driver_features] DRRS State Enabled:1 [ 1.621202] [drm:parse_ddi_port] Port A VBT info: DP:1 HDMI:0 DVI:0 EDP:1 CRT:0 [ 1.621203] [drm:parse_ddi_port] VBT HDMI level shift for port A: 0 [ 1.621204] [drm:parse_ddi_port] Port B VBT info: DP:1 HDMI:1 DVI:1 EDP:0 CRT:0 [ 1.621205] [drm:parse_ddi_port] VBT HDMI level shift for port B: 8 [ 1.621206] [drm:parse_ddi_port] Port C VBT info: DP:1 HDMI:1 DVI:1 EDP:0 CRT:0 [ 1.621207] [drm:parse_ddi_port] VBT HDMI level shift for port C: 8 [ 1.621224] [drm:intel_dsm_pci_probe] no _DSM method for intel device [ 1.621228] [drm:gen9_set_dc_state] Setting DC state from 00 to 00 [ 1.621230] [drm:intel_power_well_enable] enabling power well 1 [ 1.621232] [drm:intel_update_cdclk] Current CD clock rate: 144000 kHz, VCO: 1152000 kHz, ref: 19200 kHz [ 1.621244] [drm:intel_power_well_enable] enabling always-on [ 1.621245] [drm:intel_power_well_enable] enabling DC off [ 1.621246] [drm:gen9_set_dc_state] Setting DC state from 00 to 00 [ 1.621248] [drm:intel_power_well_enable] enabling power well 2 [ 1.621249] [drm:intel_power_well_enable] enabling dpio-common-a [ 1.621256] [drm:bxt_ddi_phy_init] DDI PHY 1 already enabled, won't reprogram it [ 1.621257] [drm:intel_power_well_enable] enabling dpio-common-bc [ 1.621939] [drm:gen9_set_dc_state] Setting DC state from 00 to 00 [ 1.621955] [drm:bxt_ddi_phy_init] DDI PHY 1 already enabled, won't reprogram it [ 1.621965] [drm:bxt_ddi_phy_init] DDI PHY 0 already enabled, won't reprogram it [ 1.621967] [drm:intel_csr_ucode_init] Loading i915/bxt_dmc_ver1_07.bin [ 1.622107] [drm] Finished loading i915/bxt_dmc_ver1_07.bin (v1.7) [ 1.622353] [drm:intel_fbc_init] Sanitized enable_fbc value: 0 [ 1.622358] [drm:intel_print_wm_latency] Gen9 Plane WM0 latency 9 (9.0 usec) [ 1.622359] [drm:intel_print_wm_latency] Gen9 Plane WM1 latency 9 (9.0 usec) [ 1.622360] [drm:intel_print_wm_latency] Gen9 Plane WM2 latency 10 (10.0 usec) [ 1.622361] [drm:intel_print_wm_latency] Gen9 Plane WM3 latency 24 (24.0 usec) [ 1.622362] [drm:intel_print_wm_latency] Gen9 Plane WM4 latency 24 (24.0 usec) [ 1.622362] [drm:intel_print_wm_latency] Gen9 Plane WM5 latency 24 (24.0 usec) [ 1.622363] [drm:intel_print_wm_latency] Gen9 Plane WM6 latency 24 (24.0 usec) [ 1.622364] [drm:intel_print_wm_latency] Gen9 Plane WM7 latency 24 (24.0 usec) [ 1.622365] [drm:intel_modeset_init] 3 display pipes available. [ 1.622375] [drm:intel_update_cdclk] Current CD clock rate: 144000 kHz, VCO: 1152000 kHz, ref: 19200 kHz [ 1.622377] [drm:intel_update_max_cdclk] Max CD clock rate: 624000 kHz [ 1.622377] [drm:intel_update_max_cdclk] Max dotclock rate: 624000 kHz [ 1.622379] vgaarb: device changed decodes: PCI:0000:00:02.0,olddecodes=io+mem,decodes=io+mem:owns=io+mem [ 1.622685] [drm:intel_ddi_init] BXT BIOS forgot to set DDI_A_4_LANES for port A; fixing [ 1.622686] [drm:intel_dp_init_connector] Adding eDP connector on port A [ 1.622697] [drm:intel_pps_dump_state] cur t1_t3 0 t8 0 t9 0 t10 500 t11_t12 5000 [ 1.622698] [drm:intel_pps_dump_state] vbt t1_t3 2000 t8 10 t9 2000 t10 500 t11_t12 5000 [ 1.622699] [drm:intel_dp_init_panel_power_sequencer] panel power up delay 200, power down delay 50, power cycle delay 500 [ 1.622700] [drm:intel_dp_init_panel_power_sequencer] backlight on delay 1, off delay 200 [ 1.622701] [drm:intel_dp_init_panel_power_sequencer_registers] panel power sequencer register settings: PP_ON 0x7d00001, PP_OFF 0x1f40001, PP_DIV 0x60 [ 1.622704] [drm:edp_panel_vdd_on] Turning eDP port A VDD on [ 1.622705] [drm:edp_panel_vdd_on] PP_STATUS: 0x80000008 PP_CONTROL: 0x0000006f [ 1.622812] [drm:intel_dp_get_dpcd] DPCD: 11 0a 82 41 00 00 01 80 02 00 00 00 0f 0b 00 [ 1.622968] [drm:intel_dp_get_dpcd] Detected EDP PSR Panel. [ 1.623052] [drm:intel_dp_get_dpcd] EDP DPCD : 02 fb c7 [ 1.623053] [drm:intel_dp_get_dpcd] Display Port TPS3 support: source yes, sink no [ 1.623054] [drm:intel_dp_print_rates] source rates: 162000, 216000, 243000, 270000, 324000, 432000, 540000 [ 1.623055] [drm:intel_dp_print_rates] sink rates: 162000, 270000 [ 1.623056] [drm:intel_dp_print_rates] common rates: 162000, 270000 [ 1.623910] [drm:drm_edid_to_eld] ELD: no CEA Extension found [ 1.623911] [drm:intel_dp_drrs_init] Downclock mode is not found. DRRS not supported [ 1.623913] [drm:intel_panel_setup_backlight] Connector eDP-1 backlight initialized, enabled, brightness 67764/96000 [ 1.623922] [drm:intel_dp_init_connector] Adding DP connector on port B [ 1.623930] [drm:intel_hdmi_init_connector] Adding HDMI connector on port B [ 1.623935] [drm:intel_dp_init_connector] Adding DP connector on port C [ 1.623941] [drm:intel_hdmi_init_connector] Adding HDMI connector on port C [ 1.623943] [drm:intel_dsi_init] [ 1.623954] [drm:intel_modeset_readout_hw_state] [CRTC:26:pipe A] hw state readout: enabled [ 1.623956] [drm:intel_modeset_readout_hw_state] [CRTC:31:pipe B] hw state readout: disabled [ 1.623957] [drm:intel_modeset_readout_hw_state] [CRTC:36:pipe C] hw state readout: disabled [ 1.623963] [drm:intel_modeset_readout_hw_state] PORT PLL A hw state readout: crtc_mask 0x00000001, on 1 [ 1.623964] [drm:intel_modeset_readout_hw_state] PORT PLL B hw state readout: crtc_mask 0x00000000, on 0 [ 1.623965] [drm:intel_modeset_readout_hw_state] PORT PLL C hw state readout: crtc_mask 0x00000000, on 0 [ 1.623968] [drm:intel_ddi_get_config] pipe has 24 bpp for eDP panel, overriding BIOS-provided max 18 bpp [ 1.623971] [drm:intel_modeset_readout_hw_state] [ENCODER:38:DDI A] hw state readout: enabled, pipe A [ 1.623973] [drm:intel_modeset_readout_hw_state] [ENCODER:46:DDI B] hw state readout: disabled, pipe A [ 1.623974] [drm:intel_modeset_readout_hw_state] [ENCODER:48:DP-MST A] hw state readout: disabled, pipe A [ 1.623975] [drm:intel_modeset_readout_hw_state] [ENCODER:49:DP-MST B] hw state readout: disabled, pipe B [ 1.623975] [drm:intel_modeset_readout_hw_state] [ENCODER:50:DP-MST C] hw state readout: disabled, pipe C [ 1.623977] [drm:intel_modeset_readout_hw_state] [ENCODER:53:DDI C] hw state readout: disabled, pipe A [ 1.623977] [drm:intel_modeset_readout_hw_state] [ENCODER:55:DP-MST A] hw state readout: disabled, pipe A [ 1.623978] [drm:intel_modeset_readout_hw_state] [ENCODER:56:DP-MST B] hw state readout: disabled, pipe B [ 1.623979] [drm:intel_modeset_readout_hw_state] [ENCODER:57:DP-MST C] hw state readout: disabled, pipe C [ 1.623982] [drm:intel_modeset_readout_hw_state] [CONNECTOR:39:eDP-1] hw state readout: enabled [ 1.623984] [drm:intel_modeset_readout_hw_state] [CONNECTOR:47:DP-1] hw state readout: disabled [ 1.623985] [drm:intel_modeset_readout_hw_state] [CONNECTOR:51:HDMI-A-1] hw state readout: disabled [ 1.623986] [drm:intel_modeset_readout_hw_state] [CONNECTOR:54:DP-2] hw state readout: disabled [ 1.623987] [drm:intel_modeset_readout_hw_state] [CONNECTOR:58:HDMI-A-2] hw state readout: disabled [ 1.623996] [drm:intel_dump_pipe_config] [CRTC:26:pipe A][setup_hw_state] config ffff88046609b000 for pipe A [ 1.623997] [drm:intel_dump_pipe_config] cpu_transcoder: EDP [ 1.623998] [drm:intel_dump_pipe_config] pipe bpp: 24, dithering: 0 [ 1.623999] [drm:intel_dump_pipe_config] fdi/pch: 0, lanes: 0, gmch_m: 0, gmch_n: 0, link_m: 0, link_n: 0, tu: 0 [ 1.624000] [drm:intel_dump_pipe_config] dp: 1, lanes: 2, gmch_m: 6436858, gmch_n: 8388608, link_m: 268202, link_n: 524288, tu: 64 [ 1.624001] [drm:intel_dump_pipe_config] dp: 1, lanes: 2, gmch_m2: 0, gmch_n2: 0, link_m2: 0, link_n2: 0, tu2: 0 [ 1.624002] [drm:intel_dump_pipe_config] audio: 0, infoframes: 0 [ 1.624003] [drm:intel_dump_pipe_config] requested mode: [ 1.624004] [drm:drm_mode_debug_printmodeline] Modeline 0:"1920x1080" 60 138119 1920 1968 2018 2052 1080 1084 1086 1122 0x40 0xa [ 1.624005] [drm:intel_dump_pipe_config] adjusted mode: [ 1.624006] [drm:drm_mode_debug_printmodeline] Modeline 0:"1920x1080" 60 138119 1920 1968 2018 2052 1080 1084 1086 1122 0x40 0xa [ 1.624008] [drm:intel_dump_crtc_timings] crtc timings: 138119 1920 1968 2018 2052 1080 1084 1086 1122, type: 0x40 flags: 0xa [ 1.624008] [drm:intel_dump_pipe_config] port clock: 270000 [ 1.624009] [drm:intel_dump_pipe_config] pipe src size: 1920x1080 [ 1.624010] [drm:intel_dump_pipe_config] num_scalers: 2, scaler_users: 0x0, scaler_id: -1 [ 1.624011] [drm:intel_dump_pipe_config] gmch pfit: control: 0x00000000, ratios: 0x00000000, lvds border: 0x00000000 [ 1.624012] [drm:intel_dump_pipe_config] pch pfit: pos: 0x00000000, size: 0x00000000, disabled [ 1.624012] [drm:intel_dump_pipe_config] ips: 0 [ 1.624013] [drm:intel_dump_pipe_config] double wide: 0 [ 1.624015] [drm:intel_dump_pipe_config] ddi_pll_sel: 0; dpll_hw_state: ebb0: 0x8100, ebb4: 0x2000,pll0: 0x1b, pll1: 0x100, pll2: 0x0, pll3: 0x0, pll6: 0x10803, pll8: 0x9, pll9: 0xa, pll10: 0x8003c00, pcsdw12: 0x4d [ 1.624015] [drm:intel_dump_pipe_config] planes on this crtc [ 1.624016] [drm:intel_dump_pipe_config] [PLANE:23:plane 1A] disabled, scaler_id = -1 [ 1.624017] [drm:intel_dump_pipe_config] [PLANE:25:cursor A] disabled, scaler_id = -1 [ 1.624018] [drm:intel_dump_pipe_config] [PLANE:27:plane 2A] disabled, scaler_id = -1 [ 1.624019] [drm:intel_dump_pipe_config] [PLANE:28:plane 3A] disabled, scaler_id = -1 [ 1.624020] [drm:intel_dump_pipe_config] [CRTC:31:pipe B][setup_hw_state] config ffff88046609c000 for pipe B [ 1.624021] [drm:intel_dump_pipe_config] cpu_transcoder: B [ 1.624021] [drm:intel_dump_pipe_config] pipe bpp: 0, dithering: 0 [ 1.624022] [drm:intel_dump_pipe_config] fdi/pch: 0, lanes: 0, gmch_m: 0, gmch_n: 0, link_m: 0, link_n: 0, tu: 0 [ 1.624023] [drm:intel_dump_pipe_config] dp: 0, lanes: 0, gmch_m: 0, gmch_n: 0, link_m: 0, link_n: 0, tu: 0 [ 1.624024] [drm:intel_dump_pipe_config] dp: 0, lanes: 0, gmch_m2: 0, gmch_n2: 0, link_m2: 0, link_n2: 0, tu2: 0 [ 1.624025] [drm:intel_dump_pipe_config] audio: 0, infoframes: 0 [ 1.624026] [drm:intel_dump_pipe_config] requested mode: [ 1.624027] [drm:drm_mode_debug_printmodeline] Modeline 0:"" 0 0 0 0 0 0 0 0 0 0 0x0 0x0 [ 1.624028] [drm:intel_dump_pipe_config] adjusted mode: [ 1.624029] [drm:drm_mode_debug_printmodeline] Modeline 0:"" 0 0 0 0 0 0 0 0 0 0 0x0 0x0 [ 1.624030] [drm:intel_dump_crtc_timings] crtc timings: 0 0 0 0 0 0 0 0 0, type: 0x0 flags: 0x0 [ 1.624031] [drm:intel_dump_pipe_config] port clock: 0 [ 1.624032] [drm:intel_dump_pipe_config] pipe src size: 0x0 [ 1.624032] [drm:intel_dump_pipe_config] num_scalers: 2, scaler_users: 0x0, scaler_id: 0 [ 1.624033] [drm:intel_dump_pipe_config] gmch pfit: control: 0x00000000, ratios: 0x00000000, lvds border: 0x00000000 [ 1.624034] [drm:intel_dump_pipe_config] pch pfit: pos: 0x00000000, size: 0x00000000, disabled [ 1.624035] [drm:intel_dump_pipe_config] ips: 0 [ 1.624035] [drm:intel_dump_pipe_config] double wide: 0 [ 1.624037] [drm:intel_dump_pipe_config] ddi_pll_sel: 0; dpll_hw_state: ebb0: 0x0, ebb4: 0x0,pll0: 0x0, pll1: 0x0, pll2: 0x0, pll3: 0x0, pll6: 0x0, pll8: 0x0, pll9: 0x0, pll10: 0x0, pcsdw12: 0x0 [ 1.624037] [drm:intel_dump_pipe_config] planes on this crtc [ 1.624038] [drm:intel_dump_pipe_config] [PLANE:29:plane 1B] disabled, scaler_id = -1 [ 1.624039] [drm:intel_dump_pipe_config] [PLANE:30:cursor B] disabled, scaler_id = -1 [ 1.624040] [drm:intel_dump_pipe_config] [PLANE:32:plane 2B] disabled, scaler_id = -1 [ 1.624041] [drm:intel_dump_pipe_config] [PLANE:33:plane 3B] disabled, scaler_id = -1 [ 1.624044] [drm:intel_dump_pipe_config] [CRTC:36:pipe C][setup_hw_state] config ffff88046609d000 for pipe C [ 1.624045] [drm:intel_dump_pipe_config] cpu_transcoder: C [ 1.624046] [drm:intel_dump_pipe_config] pipe bpp: 0, dithering: 0 [ 1.624047] [drm:intel_dump_pipe_config] fdi/pch: 0, lanes: 0, gmch_m: 0, gmch_n: 0, link_m: 0, link_n: 0, tu: 0 [ 1.624048] [drm:intel_dump_pipe_config] dp: 0, lanes: 0, gmch_m: 0, gmch_n: 0, link_m: 0, link_n: 0, tu: 0 [ 1.624049] [drm:intel_dump_pipe_config] dp: 0, lanes: 0, gmch_m2: 0, gmch_n2: 0, link_m2: 0, link_n2: 0, tu2: 0 [ 1.624050] [drm:intel_dump_pipe_config] audio: 0, infoframes: 0 [ 1.624050] [drm:intel_dump_pipe_config] requested mode: [ 1.624052] [drm:drm_mode_debug_printmodeline] Modeline 0:"" 0 0 0 0 0 0 0 0 0 0 0x0 0x0 [ 1.624052] [drm:intel_dump_pipe_config] adjusted mode: [ 1.624053] [drm:drm_mode_debug_printmodeline] Modeline 0:"" 0 0 0 0 0 0 0 0 0 0 0x0 0x0 [ 1.624055] [drm:intel_dump_crtc_timings] crtc timings: 0 0 0 0 0 0 0 0 0, type: 0x0 flags: 0x0 [ 1.624055] [drm:intel_dump_pipe_config] port clock: 0 [ 1.624056] [drm:intel_dump_pipe_config] pipe src size: 0x0 [ 1.624057] [drm:intel_dump_pipe_config] num_scalers: 1, scaler_users: 0x0, scaler_id: 0 [ 1.624058] [drm:intel_dump_pipe_config] gmch pfit: control: 0x00000000, ratios: 0x00000000, lvds border: 0x00000000 [ 1.624059] [drm:intel_dump_pipe_config] pch pfit: pos: 0x00000000, size: 0x00000000, disabled [ 1.624059] [drm:intel_dump_pipe_config] ips: 0 [ 1.624060] [drm:intel_dump_pipe_config] double wide: 0 [ 1.624061] [drm:intel_dump_pipe_config] ddi_pll_sel: 0; dpll_hw_state: ebb0: 0x0, ebb4: 0x0,pll0: 0x0, pll1: 0x0, pll2: 0x0, pll3: 0x0, pll6: 0x0, pll8: 0x0, pll9: 0x0, pll10: 0x0, pcsdw12: 0x0 [ 1.624062] [drm:intel_dump_pipe_config] planes on this crtc [ 1.624063] [drm:intel_dump_pipe_config] [PLANE:34:plane 1C] disabled, scaler_id = -1 [ 1.624064] [drm:intel_dump_pipe_config] [PLANE:35:cursor C] disabled, scaler_id = -1 [ 1.624064] [drm:intel_dump_pipe_config] [PLANE:37:plane 2C] disabled, scaler_id = -1 [ 1.624081] [drm:intel_power_well_disable] disabling dpio-common-bc [ 1.624082] [drm:intel_power_well_disable] disabling power well 2 [ 1.624085] [drm:skl_set_power_well] Disabling power well 2 [ 1.624089] [drm:skylake_get_initial_plane_config] pipe A with fb: size=1920x1080@32, offset=0, pitch 7680, size 0x7e9000 [ 1.624090] [drm:i915_gem_object_create_stolen_for_preallocated] creating preallocated stolen object: stolen_offset=0, gtt_offset=0, size=7e9000 [ 1.624092] [drm:i915_pages_create_for_stolen] offset=0x0, size=8294400 [ 1.624095] [drm:intel_alloc_initial_plane_obj] initial plane fb obj ffff880465628000 [ 1.624096] [drm:intel_guc_init] GuC firmware pending, path i915/bxt_guc_ver8_7.bin [ 1.624097] [drm:guc_fw_fetch] before requesting firmware: GuC fw fetch status PENDING [ 1.624130] [drm:guc_fw_fetch] fetch GuC fw from i915/bxt_guc_ver8_7.bin succeeded, fw ffff88046af2a920 [ 1.624131] [drm:guc_fw_fetch] firmware version 8.7 OK (minimum 8.7) [ 1.624165] [drm:guc_fw_fetch] GuC fw fetch status SUCCESS, obj ffff880465628240 [ 1.624235] [drm:i915_gem_setup_global_gtt] reserving preallocated space: 0 + 7e9000 [ 1.624236] [drm:i915_gem_setup_global_gtt] clearing unused GTT space: [7e9000, fffff000] [ 1.625000] [drm:i915_gem_context_init] LR context support initialized [ 1.625002] [drm:i915_gem_object_create_stolen] creating stolen object: size=1000 [ 1.625004] [drm:i915_pages_create_for_stolen] offset=0x7e9000, size=4096 [ 1.625007] [drm:intel_init_pipe_control] render ring pipe control offset: 0xffffe000 [ 1.625042] [drm:i915_gem_object_create_stolen] creating stolen object: size=4000 [ 1.625044] [drm:i915_pages_create_for_stolen] offset=0x7ea000, size=16384 [ 1.625089] [drm:i915_gem_object_create_stolen] creating stolen object: size=4000 [ 1.625091] [drm:i915_pages_create_for_stolen] offset=0x7ee000, size=16384 [ 1.625128] [drm:i915_gem_object_create_stolen] creating stolen object: size=4000 [ 1.625129] [drm:i915_pages_create_for_stolen] offset=0x7f2000, size=16384 [ 1.625151] [drm:i915_gem_object_create_stolen] creating stolen object: size=4000 [ 1.625152] [drm:i915_pages_create_for_stolen] offset=0x7f6000, size=16384 [ 1.625162] [drm:gen8_init_common_ring] Execlists enabled for render ring [ 1.625186] [drm:gen8_init_common_ring] Execlists enabled for blitter ring [ 1.625203] [drm:gen8_init_common_ring] Execlists enabled for bsd ring [ 1.625220] [drm:gen8_init_common_ring] Execlists enabled for video enhancement ring [ 1.625237] [drm:intel_guc_setup] GuC fw status: path i915/bxt_guc_ver8_7.bin, fetch SUCCESS, load NONE [ 1.625239] [drm:intel_guc_setup] GuC fw status: fetch SUCCESS, load PENDING [ 1.628056] [drm:guc_ucode_xfer_dma] DMA status 0x10, GuC status 0x8002f0ec [ 1.628058] [drm:guc_ucode_xfer_dma] returning 0 [ 1.628059] [drm:intel_guc_setup] GuC fw status: fetch SUCCESS, load SUCCESS [ 1.628068] [drm:select_doorbell_register] assigned normal priority doorbell id 0x0 [ 1.628069] [drm:select_doorbell_cacheline] selected doorbell cacheline 0x0, next 0x40, linesize 64 [ 1.628080] [drm:guc_client_alloc] new priority 2 client ffff88046cf26a00: ctx_index 0 [ 1.628081] [drm:guc_client_alloc] doorbell id 0, cacheline offset 0x0 [ 1.644531] clocksource: tsc: mask: 0xffffffffffffffff max_cycles: 0x41efac32846, max_idle_ns: 440795231323 ns [ 1.647007] [drm:intel_update_cdclk] Current CD clock rate: 144000 kHz, VCO: 1152000 kHz, ref: 19200 kHz [ 1.647019] [drm:intel_fbdev_init_bios] found possible fb from plane A [ 1.647021] [drm:intel_fbdev_init_bios] pipe B not active or no fb, skipping [ 1.647021] [drm:intel_fbdev_init_bios] pipe C not active or no fb, skipping [ 1.647022] [drm:intel_fbdev_init_bios] checking plane A for BIOS fb [ 1.647023] [drm:intel_fbdev_init_bios] pipe A area: 1920x1080, bpp: 32, size: 8294400 [ 1.647024] [drm:intel_fbdev_init_bios] fb big enough for plane A (8294400 >= 8294400) [ 1.647025] [drm:intel_fbdev_init_bios] pipe B not active, skipping [ 1.647026] [drm:intel_fbdev_init_bios] pipe C not active, skipping [ 1.647027] [drm:intel_fbdev_init_bios] using BIOS fb for initial console [ 1.647030] [drm:bxt_hpd_irq_setup] Invert bit setting: hp_ctl:18001818 hp_port:38 [ 1.647287] [drm:intel_backlight_device_register] Connector eDP-1 backlight sysfs interface registered [ 1.647289] [drm:intel_dp_connector_register] registering DPDDC-A bus for card0-eDP-1 [ 1.647520] [drm:intel_dp_connector_register] registering DPDDC-B bus for card0-DP-1 [ 1.647742] [drm:intel_dp_connector_register] registering DPDDC-C bus for card0-DP-2 [ 1.648311] [drm:intel_didl_outputs] More than 15 outputs detected via ACPI [ 1.649725] ACPI: Video Device [GFX0] (multi-head: yes rom: no post: no) [ 1.649876] input: Video Bus as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0A08:00/LNXVIDEO:00/input/input4 [ 1.649950] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:39:eDP-1] [ 1.649951] [drm:intel_dp_detect] [CONNECTOR:39:eDP-1] [ 1.650042] [drm:intel_dp_probe_oui] Sink OUI: 001cf8 [ 1.650118] [drm:intel_dp_probe_oui] Branch OUI: 000000 [ 1.650233] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:39:eDP-1] status updated from unknown to connected [ 1.650241] [drm:drm_edid_to_eld] ELD: no CEA Extension found [ 1.650243] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:39:eDP-1] probed modes : [ 1.650245] [drm:drm_mode_debug_printmodeline] Modeline 40:"1920x1080" 60 138120 1920 1968 2018 2052 1080 1084 1086 1122 0x48 0xa [ 1.650246] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:47:DP-1] [ 1.650247] [drm:intel_dp_detect] [CONNECTOR:47:DP-1] [ 1.650248] [drm:intel_power_well_enable] enabling power well 2 [ 1.650249] [drm:skl_set_power_well] Enabling power well 2 [ 1.650253] [drm:intel_power_well_enable] enabling dpio-common-bc [ 1.650285] [drm:intel_power_well_disable] disabling dpio-common-bc [ 1.650287] [drm:intel_power_well_disable] disabling power well 2 [ 1.650289] [drm:skl_set_power_well] Disabling power well 2 [ 1.650291] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:47:DP-1] status updated from unknown to disconnected [ 1.650293] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:47:DP-1] disconnected [ 1.650294] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:51:HDMI-A-1] [ 1.650295] [drm:intel_hdmi_detect] [CONNECTOR:51:HDMI-A-1] [ 1.650296] [drm:intel_power_well_enable] enabling power well 2 [ 1.650297] [drm:skl_set_power_well] Enabling power well 2 [ 1.657183] usb 1-7: New USB device found, idVendor=8087, idProduct=0a2a [ 1.657187] usb 1-7: New USB device strings: Mfr=0, Product=0, SerialNumber=0 [ 1.674308] usb 1-2.2: new high-speed USB device number 4 using xhci_hcd [ 1.683284] mmc1: new HS400 MMC card at address 0001 [ 1.691312] [drm:intel_hdmi_detect] HDMI live status down [ 1.691314] [drm:intel_power_well_disable] disabling power well 2 [ 1.691317] [drm:skl_set_power_well] Disabling power well 2 [ 1.691319] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:51:HDMI-A-1] status updated from unknown to disconnected [ 1.691320] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:51:HDMI-A-1] disconnected [ 1.691322] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:54:DP-2] [ 1.691323] [drm:intel_dp_detect] [CONNECTOR:54:DP-2] [ 1.691324] [drm:intel_power_well_enable] enabling power well 2 [ 1.691325] [drm:skl_set_power_well] Enabling power well 2 [ 1.691329] [drm:intel_power_well_enable] enabling dpio-common-bc [ 1.691358] [drm:intel_power_well_disable] disabling dpio-common-bc [ 1.691359] [drm:intel_power_well_disable] disabling power well 2 [ 1.691362] [drm:skl_set_power_well] Disabling power well 2 [ 1.691363] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:54:DP-2] status updated from unknown to disconnected [ 1.691364] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:54:DP-2] disconnected [ 1.691365] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:58:HDMI-A-2] [ 1.691366] [drm:intel_hdmi_detect] [CONNECTOR:58:HDMI-A-2] [ 1.691366] [drm:intel_power_well_enable] enabling power well 2 [ 1.691367] [drm:skl_set_power_well] Enabling power well 2 [ 1.698585] mmcblk1: mmc1:0001 CGND3R 58.2 GiB [ 1.698639] mmcblk1boot0: mmc1:0001 CGND3R partition 1 4.00 MiB [ 1.698689] mmcblk1boot1: mmc1:0001 CGND3R partition 2 4.00 MiB [ 1.698734] mmcblk1rpmb: mmc1:0001 CGND3R partition 3 4.00 MiB [ 1.698889] usb 1-2.2: New USB device found, idVendor=413c, idProduct=1010 [ 1.698893] usb 1-2.2: New USB device strings: Mfr=0, Product=1, SerialNumber=0 [ 1.698897] usb 1-2.2: Product: USB 2.0 Hub [MTT] [ 1.699030] hub 1-2.2:1.0: USB hub found [ 1.699051] hub 1-2.2:1.0: 4 ports detected [ 1.699438] mmcblk1: p1 p2 p3 p4 [ 1.714536] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [ 1.714614] ata1.00: ATA-8: INTEL SSDSA2BW160G3H, 4PC10365, max UDMA/133 [ 1.714617] ata1.00: 312581808 sectors, multi 1: LBA48 NCQ (depth 31/32) [ 1.714698] ata1.00: configured for UDMA/133 [ 1.714787] scsi 0:0:0:0: Direct-Access ATA INTEL SSDSA2BW16 0365 PQ: 0 ANSI: 5 [ 1.718927] usb 1-2.3: new low-speed USB device number 5 using xhci_hcd [ 1.728654] ata1.00: Enabling discard_zeroes_data [ 1.728670] sd 0:0:0:0: [sda] 312581808 512-byte logical blocks: (160 GB/149 GiB) [ 1.728734] sd 0:0:0:0: [sda] Write Protect is off [ 1.728737] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 [ 1.728754] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 1.728809] ata1.00: Enabling discard_zeroes_data [ 1.728837] sd 0:0:0:0: Attached scsi generic sg0 type 0 [ 1.731806] [drm:intel_hdmi_detect] HDMI live status down [ 1.731808] [drm:intel_power_well_disable] disabling power well 2 [ 1.731812] [drm:skl_set_power_well] Disabling power well 2 [ 1.731814] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:58:HDMI-A-2] status updated from unknown to disconnected [ 1.731815] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:58:HDMI-A-2] disconnected [ 1.731818] [drm:drm_setup_crtcs] [ 1.731819] [drm:drm_enable_connectors] connector 39 enabled? yes [ 1.731820] [drm:drm_enable_connectors] connector 47 enabled? no [ 1.731820] [drm:drm_enable_connectors] connector 51 enabled? no [ 1.731821] [drm:drm_enable_connectors] connector 54 enabled? no [ 1.731822] [drm:drm_enable_connectors] connector 58 enabled? no [ 1.731823] [drm:intel_fb_initial_config] looking for cmdline mode on connector eDP-1 [ 1.731824] [drm:intel_fb_initial_config] looking for preferred mode on connector eDP-1 0 [ 1.731826] [drm:intel_fb_initial_config] connector eDP-1 on [CRTC:26:pipe A]: 1920x1080 [ 1.731826] [drm:intel_fb_initial_config] connector DP-1 not enabled, skipping [ 1.731827] [drm:intel_fb_initial_config] connector HDMI-A-1 not enabled, skipping [ 1.731828] [drm:intel_fb_initial_config] connector DP-2 not enabled, skipping [ 1.731829] [drm:intel_fb_initial_config] connector HDMI-A-2 not enabled, skipping [ 1.731830] [drm:drm_setup_crtcs] desired mode 1920x1080 set on crtc 26 (0,0) [ 1.731831] [drm:intelfb_create] re-using BIOS fb [ 1.731835] [drm:intelfb_create] allocated 1920x1080 fb: 0x00000000, bo ffff880465628000 [ 1.731865] fbcon: inteldrmfb (fb0) is primary device [ 1.731909] [drm:connected_sink_compute_bpp] [CONNECTOR:39:eDP-1] checking for sink bpp constrains [ 1.731910] [drm:connected_sink_compute_bpp] clamping display bpp (was 36) to EDID reported max of 24 [ 1.731911] [drm:skl_update_scaler_crtc] Updating scaler for [CRTC:26:pipe A] scaler_user index 0.31 [ 1.731912] [drm:intel_dp_compute_config] DP link computation with max lane count 2 max bw 270000 pixel clock 138120KHz [ 1.731914] [drm:intel_dp_compute_config] DP link bw 0a rate select 00 lane count 2 clock 270000 bpp 24 [ 1.731915] [drm:intel_dp_compute_config] DP link bw required 331488 available 432000 [ 1.731915] [drm:intel_modeset_pipe_config] hw max bpp: 36, pipe bpp: 24, dithering: 0 [ 1.731917] [drm:intel_dump_pipe_config] [CRTC:26:pipe A][modeset] config ffff8804656a5000 for pipe A [ 1.731917] [drm:intel_dump_pipe_config] cpu_transcoder: EDP [ 1.731917] [drm:intel_dump_pipe_config] pipe bpp: 24, dithering: 0 [ 1.731918] [drm:intel_dump_pipe_config] fdi/pch: 0, lanes: 0, gmch_m: 0, gmch_n: 0, link_m: 0, link_n: 0, tu: 0 [ 1.731919] [drm:intel_dump_pipe_config] dp: 1, lanes: 2, gmch_m: 6436858, gmch_n: 8388608, link_m: 268202, link_n: 524288, tu: 64 [ 1.731919] [drm:intel_dump_pipe_config] dp: 1, lanes: 2, gmch_m2: 0, gmch_n2: 0, link_m2: 0, link_n2: 0, tu2: 0 [ 1.731920] [drm:intel_dump_pipe_config] audio: 0, infoframes: 0 [ 1.731920] [drm:intel_dump_pipe_config] requested mode: [ 1.731921] [drm:drm_mode_debug_printmodeline] Modeline 0:"1920x1080" 60 138120 1920 1968 2018 2052 1080 1084 1086 1122 0x48 0xa [ 1.731922] [drm:intel_dump_pipe_config] adjusted mode: [ 1.731923] [drm:drm_mode_debug_printmodeline] Modeline 0:"1920x1080" 60 138120 1920 1968 2018 2052 1080 1084 1086 1122 0x48 0xa [ 1.731924] [drm:intel_dump_crtc_timings] crtc timings: 138120 1920 1968 2018 2052 1080 1084 1086 1122, type: 0x48 flags: 0xa [ 1.731924] [drm:intel_dump_pipe_config] port clock: 270000 [ 1.731924] [drm:intel_dump_pipe_config] pipe src size: 1920x1080 [ 1.731925] [drm:intel_dump_pipe_config] num_scalers: 2, scaler_users: 0x0, scaler_id: -1 [ 1.731925] [drm:intel_dump_pipe_config] gmch pfit: control: 0x00000000, ratios: 0x00000000, lvds border: 0x00000000 [ 1.731926] [drm:intel_dump_pipe_config] pch pfit: pos: 0x00000000, size: 0x00000000, disabled [ 1.731926] [drm:intel_dump_pipe_config] ips: 0 [ 1.731927] [drm:intel_dump_pipe_config] double wide: 0 [ 1.731928] [drm:intel_dump_pipe_config] ddi_pll_sel: 0; dpll_hw_state: ebb0: 0x8100, ebb4: 0x2000,pll0: 0x1b, pll1: 0x100, pll2: 0x0, pll3: 0x0, pll6: 0x10803, pll8: 0x9, pll9: 0xa, pll10: 0x8003c00, pcsdw12: 0x4d [ 1.731928] [drm:intel_dump_pipe_config] planes on this crtc [ 1.731930] [drm:intel_dump_pipe_config] [PLANE:23:plane 1A] enabled [ 1.731930] [drm:intel_dump_pipe_config] FB:60, fb = 1920x1080 format = XR24 little-endian (0x34325258) [ 1.731930] [drm:intel_dump_pipe_config] scaler:-1 src 0x0+1920+1080 dst 0x0+1920+1080 [ 1.731931] [drm:intel_dump_pipe_config] [PLANE:25:cursor A] disabled, scaler_id = -1 [ 1.731931] [drm:intel_dump_pipe_config] [PLANE:27:plane 2A] disabled, scaler_id = -1 [ 1.731932] [drm:intel_dump_pipe_config] [PLANE:28:plane 3A] disabled, scaler_id = -1 [ 1.731933] [drm:intel_modeset_checks] New cdclk calculated to be atomic 144000, actual 144000 [ 1.731935] [drm:skl_update_scaler_plane] Updating scaler for [PLANE:23:plane 1A] scaler_user index 0.0 [ 1.731936] [drm:bxt_get_dpll] [CRTC:26:pipe A] using pre-allocated PORT PLL A [ 1.731937] [drm:intel_reference_shared_dpll] using PORT PLL A for pipe A [ 1.731937] [drm:skl_update_scaler_crtc] Updating scaler for [CRTC:26:pipe A] scaler_user index 0.31 [ 1.731948] [drm:intel_edp_backlight_off] [ 1.734685] sda: sda1 sda2 sda3 [ 1.734824] ata1.00: Enabling discard_zeroes_data [ 1.734899] sd 0:0:0:0: [sda] Attached SCSI disk [ 1.751583] usb 1-2.3: New USB device found, idVendor=04b3, idProduct=310c [ 1.751584] usb 1-2.3: New USB device strings: Mfr=0, Product=2, SerialNumber=0 [ 1.751585] usb 1-2.3: Product: USB Optical Mouse [ 1.809592] [drm:intel_panel_actually_set_backlight] set backlight PWM = 0 [ 1.809594] usb 1-2.4: new full-speed USB device number 6 using xhci_hcd [ 1.809598] [drm:intel_disable_pipe] disabling pipe A [ 1.858004] [drm:edp_panel_off] Turn eDP port A panel power off [ 1.858006] [drm:wait_panel_off] Wait for panel power off time [ 1.858007] [drm:wait_panel_status] mask b0000000 value 00000000 status 80000008 control 00000060 [ 1.871305] [drm:wait_panel_status] Wait complete [ 1.871307] [drm:intel_disable_shared_dpll] disable PORT PLL A (active 1, on? 1) for crtc 26 [ 1.871312] [drm:intel_disable_shared_dpll] disabling PORT PLL A [ 1.871315] [drm:verify_encoder_state] [ENCODER:38:DDI A] [ 1.871315] [drm:verify_encoder_state] [ENCODER:46:DDI B] [ 1.871316] [drm:verify_encoder_state] [ENCODER:48:DP-MST A] [ 1.871316] [drm:verify_encoder_state] [ENCODER:49:DP-MST B] [ 1.871317] [drm:verify_encoder_state] [ENCODER:50:DP-MST C] [ 1.871317] [drm:verify_encoder_state] [ENCODER:53:DDI C] [ 1.871318] [drm:verify_encoder_state] [ENCODER:55:DP-MST A] [ 1.871318] [drm:verify_encoder_state] [ENCODER:56:DP-MST B] [ 1.871318] [drm:verify_encoder_state] [ENCODER:57:DP-MST C] [ 1.871319] [drm:intel_connector_verify_state] [CONNECTOR:47:DP-1] [ 1.871319] [drm:intel_connector_verify_state] [CONNECTOR:51:HDMI-A-1] [ 1.871320] [drm:intel_connector_verify_state] [CONNECTOR:54:DP-2] [ 1.871320] [drm:intel_connector_verify_state] [CONNECTOR:58:HDMI-A-2] [ 1.871321] [drm:verify_single_dpll_state] PORT PLL A [ 1.871322] [drm:verify_single_dpll_state] PORT PLL B [ 1.871322] [drm:verify_single_dpll_state] PORT PLL C [ 1.871327] [drm:intel_enable_shared_dpll] enable PORT PLL A (active 1, on? 0) for crtc 26 [ 1.871327] [drm:intel_enable_shared_dpll] enabling PORT PLL A [ 1.871365] [drm:edp_panel_on] Turn eDP port A panel power on [ 1.871366] [drm:wait_panel_power_cycle] Wait for panel power cycle [ 1.871679] [drm:intel_get_hpd_pins] hotplug event received, stat 0x00000008, dig 0x1a001818, pins 0x00000010 [ 1.871680] [drm:intel_hpd_irq_handler] digital hpd port A - long [ 1.871681] [drm:intel_hpd_irq_storm_detect] Received HPD interrupt on PIN 4 - cnt: 0 [ 1.871690] [drm:intel_dp_hpd_pulse] ignoring long hpd on eDP port A [ 1.896406] usb 1-2.2.4: new low-speed USB device number 7 using xhci_hcd [ 1.982447] [drm:wait_panel_status] mask b800000f value 00000000 status 08000001 control 00000060 [ 1.984384] usb 1-2.2.4: New USB device found, idVendor=413c, idProduct=2110 [ 1.984385] usb 1-2.2.4: New USB device strings: Mfr=1, Product=2, SerialNumber=0 [ 1.984385] usb 1-2.2.4: Product: Dell Wired Multimedia Keyboard [ 1.984386] usb 1-2.2.4: Manufacturer: Dell [ 1.987435] clocksource: timekeeping watchdog on CPU1: Marking clocksource 'tsc' as unstable because the skew is too large: [ 1.987435] clocksource: 'hpet' wd_now: 9a21ee3 wd_last: 890aaa8 mask: ffffffff [ 1.987436] clocksource: 'tsc' cs_now: aa1044ff9 cs_last: a64216d33 mask: ffffffffffffffff [ 2.003644] usb 1-2.4: new full-speed USB device number 8 using xhci_hcd [ 2.010440] [drm:wait_panel_status] Wait complete [ 2.010441] [drm:wait_panel_on] Wait for panel power on [ 2.010442] [drm:wait_panel_status] mask b000000f value 80000008 status 9000000a control 00000063 [ 2.036157] [drm:intel_get_hpd_pins] hotplug event received, stat 0x00000008, dig 0x1a001818, pins 0x00000010 [ 2.036158] [drm:intel_hpd_irq_handler] digital hpd port A - long [ 2.036159] [drm:intel_hpd_irq_storm_detect] Received HPD interrupt on PIN 4 - cnt: 1 [ 2.036170] [drm:intel_dp_hpd_pulse] ignoring long hpd on eDP port A [ 2.060195] [drm:wait_panel_status] Wait complete [ 2.060202] [drm:edp_panel_vdd_on] Turning eDP port A VDD on [ 2.060204] [drm:edp_panel_vdd_on] PP_STATUS: 0x80000008 PP_CONTROL: 0x0000006b [ 2.060935] [drm:intel_dp_set_signal_levels] Using vswing level 0 [ 2.060936] [drm:intel_dp_set_signal_levels] Using pre-emphasis level 0 [ 2.061176] [drm:intel_dp_link_training_clock_recovery] clock recovery OK [ 2.061712] [drm:intel_dp_link_training_channel_equalization] Channel EQ done. DP Training successful [ 2.061755] [drm:skylake_pfit_enable] for crtc_state = ffff8804656a5000 [ 2.061815] [drm:skl_wm_flush_pipe] flush pipe A (pass 3) [ 2.061816] [drm:intel_enable_pipe] enabling pipe A [ 2.061823] [drm:intel_edp_backlight_on] [ 2.061823] [drm:intel_panel_enable_backlight] pipe A [ 2.061824] [drm:intel_panel_actually_set_backlight] set backlight PWM = 67764 [ 2.063041] [drm:intel_psr_enable] PSR not supported on this platform [ 2.063042] [drm:intel_edp_drrs_enable] Panel doesn't support DRRS [ 2.063062] [drm:skl_wm_flush_pipe] flush pipe A (pass 3) [ 2.063065] [drm:skl_wm_flush_pipe] flush pipe A (pass 3) [ 2.065843] [drm:intel_connector_verify_state] [CONNECTOR:39:eDP-1] [ 2.065845] [drm:verify_crtc_state] [CRTC:26:pipe A] [ 2.065859] [drm:verify_single_dpll_state] PORT PLL A [ 2.065870] [drm:drm_fb_helper_hotplug_event] [ 2.065870] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:39:eDP-1] [ 2.065871] [drm:intel_dp_detect] [CONNECTOR:39:eDP-1] [ 2.065961] [drm:intel_dp_probe_oui] Sink OUI: 001cf8 [ 2.066047] [drm:intel_dp_probe_oui] Branch OUI: 000000 [ 2.066145] [drm:drm_edid_to_eld] ELD: no CEA Extension found [ 2.066146] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:39:eDP-1] probed modes : [ 2.066148] [drm:drm_mode_debug_printmodeline] Modeline 40:"1920x1080" 60 138120 1920 1968 2018 2052 1080 1084 1086 1122 0x48 0xa [ 2.066148] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:47:DP-1] [ 2.066148] [drm:intel_dp_detect] [CONNECTOR:47:DP-1] [ 2.066149] [drm:intel_power_well_enable] enabling power well 2 [ 2.066150] [drm:skl_set_power_well] Enabling power well 2 [ 2.068168] [drm:intel_power_well_enable] enabling dpio-common-bc [ 2.068199] [drm:intel_power_well_disable] disabling dpio-common-bc [ 2.068200] [drm:intel_power_well_disable] disabling power well 2 [ 2.068210] [drm:skl_set_power_well] Disabling power well 2 [ 2.068211] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:47:DP-1] disconnected [ 2.068212] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:51:HDMI-A-1] [ 2.068212] [drm:intel_hdmi_detect] [CONNECTOR:51:HDMI-A-1] [ 2.068213] [drm:intel_power_well_enable] enabling power well 2 [ 2.068214] [drm:skl_set_power_well] Enabling power well 2 [ 2.103873] usb 1-2.4: new high-speed USB device number 9 using xhci_hcd [ 2.122201] usb 1-2.4: New USB device found, idVendor=0b95, idProduct=7720 [ 2.122202] usb 1-2.4: New USB device strings: Mfr=1, Product=2, SerialNumber=3 [ 2.122202] usb 1-2.4: Product: AX88772 [ 2.122203] usb 1-2.4: SerialNumber: 00D91E [ 2.127558] usbcore: registered new interface driver usbhid [ 2.127559] usbhid: USB HID core driver [ 2.128601] input: USB Optical Mouse as /devices/pci0000:00/0000:00:15.0/usb1/1-2/1-2.3/1-2.3:1.0/0003:04B3:310C.0001/input/input5 [ 2.128669] hid-generic 0003:04B3:310C.0001: input,hidraw0: USB HID v1.11 Mouse [USB Optical Mouse] on usb-0000:00:15.0-2.3/input0 [ 2.128750] input: Dell Dell Wired Multimedia Keyboard as /devices/pci0000:00/0000:00:15.0/usb1/1-2/1-2.2/1-2.2.4/1-2.2.4:1.0/0003:413C:2110.0002/input/input6 [ 2.147651] hid-generic 0003:413C:2110.0002: input,hidraw1: USB HID v1.10 Keyboard [Dell Dell Wired Multimedia Keyboard] on usb-0000:00:15.0-2.2.4/input0 [ 2.147758] input: Dell Dell Wired Multimedia Keyboard as /devices/pci0000:00/0000:00:15.0/usb1/1-2/1-2.2/1-2.2.4/1-2.2.4:1.1/0003:413C:2110.0003/input/input7 [ 2.153579] [drm:intel_hdmi_detect] HDMI live status down [ 2.153580] [drm:intel_power_well_disable] disabling power well 2 [ 2.153583] [drm:skl_set_power_well] Disabling power well 2 [ 2.153585] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:51:HDMI-A-1] disconnected [ 2.153586] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:54:DP-2] [ 2.153586] [drm:intel_dp_detect] [CONNECTOR:54:DP-2] [ 2.153587] [drm:intel_power_well_enable] enabling power well 2 [ 2.153588] [drm:skl_set_power_well] Enabling power well 2 [ 2.155085] [drm:intel_power_well_enable] enabling dpio-common-bc [ 2.155120] [drm:intel_power_well_disable] disabling dpio-common-bc [ 2.155121] [drm:intel_power_well_disable] disabling power well 2 [ 2.155123] [drm:skl_set_power_well] Disabling power well 2 [ 2.155124] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:54:DP-2] disconnected [ 2.155124] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:58:HDMI-A-2] [ 2.155125] [drm:intel_hdmi_detect] [CONNECTOR:58:HDMI-A-2] [ 2.155125] [drm:intel_power_well_enable] enabling power well 2 [ 2.155126] [drm:skl_set_power_well] Enabling power well 2 [ 2.171274] hid-generic 0003:413C:2110.0003: input,hiddev0,hidraw2: USB HID v1.10 Mouse [Dell Dell Wired Multimedia Keyboard] on usb-0000:00:15.0-2.2.4/input1 [ 2.222920] [drm] RC6 on [ 2.258583] [drm:intel_hdmi_detect] HDMI live status down [ 2.258584] [drm:intel_power_well_disable] disabling power well 2 [ 2.258587] [drm:skl_set_power_well] Disabling power well 2 [ 2.258589] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:58:HDMI-A-2] disconnected [ 2.258591] [drm:drm_setup_crtcs] [ 2.258592] [drm:drm_enable_connectors] connector 39 enabled? yes [ 2.258593] [drm:drm_enable_connectors] connector 47 enabled? no [ 2.258593] [drm:drm_enable_connectors] connector 51 enabled? no [ 2.258594] [drm:drm_enable_connectors] connector 54 enabled? no [ 2.258594] [drm:drm_enable_connectors] connector 58 enabled? no [ 2.258595] [drm:intel_fb_initial_config] looking for cmdline mode on connector eDP-1 [ 2.258596] [drm:intel_fb_initial_config] looking for preferred mode on connector eDP-1 0 [ 2.258597] [drm:intel_fb_initial_config] connector eDP-1 on [CRTC:26:pipe A]: 1920x1080 [ 2.258597] [drm:intel_fb_initial_config] connector DP-1 not enabled, skipping [ 2.258597] [drm:intel_fb_initial_config] connector HDMI-A-1 not enabled, skipping [ 2.258598] [drm:intel_fb_initial_config] connector DP-2 not enabled, skipping [ 2.258598] [drm:intel_fb_initial_config] connector HDMI-A-2 not enabled, skipping [ 2.258599] [drm:drm_setup_crtcs] desired mode 1920x1080 set on crtc 26 (0,0) [ 2.258609] [drm:skl_update_scaler_plane] Updating scaler for [PLANE:23:plane 1A] scaler_user index 0.0 [ 2.261264] Console: switching to colour frame buffer device 240x67 [ 2.261273] [drm:skl_update_scaler_plane] Updating scaler for [PLANE:23:plane 1A] scaler_user index 0.0 [ 2.269455] i915 0000:00:02.0: fb0: inteldrmfb frame buffer device [ 2.313412] EXT4-fs (sda2): mounted filesystem with ordered data mode. Opts: (null) [ 2.382079] systemd[1]: systemd 229 running in system mode. (+PAM +AUDIT +SELINUX +IMA +APPARMOR +SMACK +SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ -LZ4 +SECCOMP +BLKID +ELFUTILS +KMOD -IDN) [ 2.383289] systemd[1]: Detected architecture x86-64. [ 2.389709] systemd[1]: Set hostname to . [ 2.433731] systemd[1]: Listening on fsck to fsckd communication Socket. [ 2.436498] systemd[1]: Listening on Journal Socket. [ 2.439238] systemd[1]: Created slice System Slice. [ 2.446186] systemd[1]: Started Read required files in advance. [ 2.449273] systemd[1]: Starting Create list of required static device nodes for the current kernel... [ 2.452306] systemd[1]: Mounting POSIX Message Queue File System... [ 2.455194] systemd[1]: Set up automount Arbitrary Executable File Formats File System Automount Point. [ 2.458180] systemd[1]: Listening on Journal Audit Socket. [ 2.460997] systemd[1]: Listening on udev Kernel Socket. [ 2.463799] systemd[1]: Reached target Remote File Systems (Pre). [ 2.466596] systemd[1]: Reached target Remote File Systems. [ 2.478768] systemd[1]: Mounting Debug File System... [ 2.481680] systemd[1]: Created slice system-getty.slice. [ 2.484513] systemd[1]: Listening on /dev/initctl Compatibility Named Pipe. [ 2.487629] systemd[1]: Mounting Huge Pages File System... [ 2.490490] systemd[1]: Created slice User and Session Slice. [ 2.493577] systemd[1]: Started Braille Device Support. [ 2.496468] systemd[1]: Started Forward Password Requests to Wall Directory Watch. [ 2.499375] systemd[1]: Listening on Syslog Socket. [ 2.502289] systemd[1]: Listening on Journal Socket (/dev/log). [ 2.505439] systemd[1]: Starting Journal Service... [ 2.508274] systemd[1]: Listening on udev Control Socket. [ 2.511339] systemd[1]: Starting Uncomplicated firewall... [ 2.514777] systemd[1]: Starting Load Kernel Modules... [ 2.517059] systemd[1]: Created slice system-systemd\x2dfsck.slice. [ 2.519296] systemd[1]: Reached target Slices. [ 2.521493] systemd[1]: Reached target Encrypted Volumes. [ 2.521927] lp: driver loaded but no devices found [ 2.525262] ppdev: user-space parallel port driver [ 2.525504] systemd[1]: Mounted Huge Pages File System. [ 2.530059] systemd[1]: Mounted POSIX Message Queue File System. [ 2.532928] systemd[1]: Mounted Debug File System. [ 2.535392] systemd[1]: ureadahead.service: Main process exited, code=exited, status=5/NOTINSTALLED [ 2.536588] systemd[1]: ureadahead.service: Unit entered failed state. [ 2.537626] systemd[1]: ureadahead.service: Failed with result 'exit-code'. [ 2.538760] systemd[1]: Started Create list of required static device nodes for the current kernel. [ 2.541663] systemd[1]: Started Uncomplicated firewall. [ 2.544235] systemd[1]: Started Load Kernel Modules. [ 2.546779] systemd[1]: Started Journal Service. [ 2.607547] EXT4-fs (sda2): re-mounted. Opts: errors=remount-ro [ 2.619088] systemd-journald[251]: Received request to flush runtime journal from PID 1 [ 2.666571] [drm:edp_panel_vdd_off_sync] Turning eDP port A VDD off [ 2.666574] [drm:edp_panel_vdd_off_sync] PP_STATUS: 0x80000008 PP_CONTROL: 0x00000067 [ 2.666574] [drm:intel_power_well_disable] disabling DC off [ 2.666578] [drm:gen9_enable_dc5] Enabling DC5 [ 2.666580] [drm:gen9_set_dc_state] Setting DC state from 00 to 01 [ 2.707668] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4 [ 2.716109] [drm:intel_backlight_device_update_status] updating intel_backlight, brightness=96000/96000 [ 2.716112] [drm:intel_panel_actually_set_backlight] set backlight PWM = 96000 [ 2.716114] [drm:intel_power_well_enable] enabling DC off [ 2.716116] [drm:gen9_set_dc_state] Setting DC state from 01 to 00 [ 2.716123] [drm:intel_power_well_disable] disabling DC off [ 2.716124] [drm:gen9_enable_dc5] Enabling DC5 [ 2.716125] [drm:gen9_set_dc_state] Setting DC state from 00 to 01 [ 2.730979] Bluetooth: Core ver 2.21 [ 2.730987] NET: Registered protocol family 31 [ 2.730988] Bluetooth: HCI device and connection manager initialized [ 2.730990] Bluetooth: HCI socket layer initialized [ 2.730991] Bluetooth: L2CAP socket layer initialized [ 2.730994] Bluetooth: SCO socket layer initialized [ 2.735497] usbcore: registered new interface driver btusb [ 2.741532] Bluetooth: hci0: read Intel version: 370810011003110e00 [ 2.741599] Intel(R) Wireless WiFi driver for Linux [ 2.741605] Copyright(c) 2003- 2015 Intel Corporation [ 2.742899] iwlwifi 0000:02:00.0: Direct firmware load for iwlwifi-7265D-21.ucode failed with error -2 [ 2.742914] iwlwifi 0000:02:00.0: Direct firmware load for iwlwifi-7265D-20.ucode failed with error -2 [ 2.742922] iwlwifi 0000:02:00.0: Direct firmware load for iwlwifi-7265D-19.ucode failed with error -2 [ 2.743029] Bluetooth: hci0: Intel Bluetooth firmware file: intel/ibt-hw-37.8.10-fw-1.10.3.11.e.bseq [ 2.743471] iwlwifi 0000:02:00.0: Direct firmware load for iwlwifi-7265D-18.ucode failed with error -2 [ 2.743487] iwlwifi 0000:02:00.0: Direct firmware load for iwlwifi-7265D-17.ucode failed with error -2 [ 2.746913] iwlwifi 0000:02:00.0: loaded firmware version 16.242414.0 op_mode iwlmvm [ 2.763162] iwlwifi 0000:02:00.0: Detected Intel(R) Dual Band Wireless AC 7265, REV=0x210 [ 2.765146] iwlwifi 0000:02:00.0: L1 Enabled - LTR Enabled [ 2.765317] iwlwifi 0000:02:00.0: L1 Enabled - LTR Enabled [ 2.786011] snd_hda_intel 0000:00:0e.0: bound 0000:00:02.0 (ops i915_audio_component_bind_ops [i915]) [ 2.787069] ieee80211 phy0: Selected rate control algorithm 'iwl-mvm-rs' [ 2.787797] Adding 3994620k swap on /dev/sda3. Priority:-1 extents:1 across:3994620k SSFS [ 2.788228] [drm:intel_power_well_enable] enabling DC off [ 2.788232] [drm:gen9_set_dc_state] Setting DC state from 01 to 00 [ 2.788251] [drm:intel_power_well_enable] enabling power well 2 [ 2.788252] [drm:skl_set_power_well] Enabling power well 2 [ 2.801262] snd_hda_codec_realtek hdaudioC0D0: autoconfig for ALC298: line_outs=1 (0x14/0x0/0x0/0x0/0x0) type:speaker [ 2.801265] snd_hda_codec_realtek hdaudioC0D0: speaker_outs=0 (0x0/0x0/0x0/0x0/0x0) [ 2.801266] snd_hda_codec_realtek hdaudioC0D0: hp_outs=1 (0x21/0x0/0x0/0x0/0x0) [ 2.801267] snd_hda_codec_realtek hdaudioC0D0: mono: mono_out=0x0 [ 2.801268] snd_hda_codec_realtek hdaudioC0D0: inputs: [ 2.801269] snd_hda_codec_realtek hdaudioC0D0: Mic=0x18 [ 2.814278] random: nonblocking pool is initialized [ 2.814432] input: HDA Intel PCH Mic as /devices/pci0000:00/0000:00:0e.0/sound/card0/input8 [ 2.814481] input: HDA Intel PCH Headphone as /devices/pci0000:00/0000:00:0e.0/sound/card0/input9 [ 2.814523] input: HDA Intel PCH HDMI/DP,pcm=3 as /devices/pci0000:00/0000:00:0e.0/sound/card0/input10 [ 2.814564] input: HDA Intel PCH HDMI/DP,pcm=7 as /devices/pci0000:00/0000:00:0e.0/sound/card0/input11 [ 2.814605] input: HDA Intel PCH HDMI/DP,pcm=8 as /devices/pci0000:00/0000:00:0e.0/sound/card0/input12 [ 2.819825] [drm:intel_power_well_disable] disabling power well 2 [ 2.819832] [drm:skl_set_power_well] Disabling power well 2 [ 2.819833] [drm:intel_power_well_disable] disabling DC off [ 2.819836] [drm:gen9_enable_dc5] Enabling DC5 [ 2.819837] [drm:gen9_set_dc_state] Setting DC state from 00 to 01 [ 2.822069] SSE version of gcm_enc/dec engaged. [ 2.840818] Bluetooth: hci0: Intel Bluetooth firmware patch completed and activated [ 2.891178] [drm:skl_update_scaler_plane] Updating scaler for [PLANE:23:plane 1A] scaler_user index 0.0 [ 2.906130] audit: type=1400 audit(1467754513.399:2): apparmor="STATUS" operation="profile_load" name="/usr/bin/ubuntu-core-launcher" pid=535 comm="apparmor_parser" [ 2.909404] [drm:skl_update_scaler_plane] Updating scaler for [PLANE:23:plane 1A] scaler_user index 0.0 [ 2.909599] audit: type=1400 audit(1467754513.415:3): apparmor="STATUS" operation="profile_load" name="/sbin/dhclient" pid=531 comm="apparmor_parser" [ 2.909602] audit: type=1400 audit(1467754513.415:4): apparmor="STATUS" operation="profile_load" name="/usr/lib/NetworkManager/nm-dhcp-client.action" pid=531 comm="apparmor_parser" [ 2.909603] audit: type=1400 audit(1467754513.415:5): apparmor="STATUS" operation="profile_load" name="/usr/lib/NetworkManager/nm-dhcp-helper" pid=531 comm="apparmor_parser" [ 2.909605] audit: type=1400 audit(1467754513.415:6): apparmor="STATUS" operation="profile_load" name="/usr/lib/connman/scripts/dhclient-script" pid=531 comm="apparmor_parser" [ 2.910910] audit: type=1400 audit(1467754513.431:7): apparmor="STATUS" operation="profile_load" name="/usr/sbin/cups-browsed" pid=543 comm="apparmor_parser" [ 2.914573] audit: type=1400 audit(1467754513.447:8): apparmor="STATUS" operation="profile_load" name="/usr/lib/lightdm/lightdm-guest-session" pid=530 comm="apparmor_parser" [ 2.914575] audit: type=1400 audit(1467754513.447:9): apparmor="STATUS" operation="profile_load" name="chromium" pid=530 comm="apparmor_parser" [ 2.915926] audit: type=1400 audit(1467754513.447:10): apparmor="STATUS" operation="profile_load" name="/usr/sbin/ippusbxd" pid=547 comm="apparmor_parser" [ 2.920214] audit: type=1400 audit(1467754513.471:11): apparmor="STATUS" operation="profile_load" name="webbrowser-app" pid=539 comm="apparmor_parser" [ 2.942931] dw-apb-uart.8: ttyS4 at MMIO 0x9232c000 (irq = 4, base_baud = 115200) is a 16550A [ 2.967534] dw-apb-uart.9: ttyS5 at MMIO 0x9232e000 (irq = 5, base_baud = 115200) is a 16550A [ 2.994803] dw-apb-uart.10: ttyS6 at MMIO 0x92330000 (irq = 6, base_baud = 115200) is a 16550A [ 3.013633] i2c_designware i2c_designware.3: i2c_dw_handle_tx_abort: lost arbitration [ 3.014414] i2c_designware i2c_designware.3: i2c_dw_handle_tx_abort: lost arbitration [ 3.015292] i2c_designware i2c_designware.3: i2c_dw_handle_tx_abort: lost arbitration [ 3.016072] i2c_designware i2c_designware.3: i2c_dw_handle_tx_abort: lost arbitration [ 3.016803] i2c_hid i2c-ELAN221D:00: hid_descr_cmd failed [ 3.020914] iwlwifi 0000:02:00.0 wlp2s0: renamed from wlan0 [ 3.021830] dw-apb-uart.11: ttyS7 at MMIO 0x92332000 (irq = 7, base_baud = 115200) is a 16550A [ 3.035502] Bluetooth: BNEP (Ethernet Emulation) ver 1.3 [ 3.035504] Bluetooth: BNEP filters: protocol multicast [ 3.035507] Bluetooth: BNEP socket layer initialized [ 3.051554] i2c_hid i2c-ALPS0001:00: hid_descr_cmd failed [ 3.137117] IPv6: ADDRCONF(NETDEV_UP): wlp2s0: link is not ready [ 3.139270] iwlwifi 0000:02:00.0: L1 Enabled - LTR Enabled [ 3.139442] iwlwifi 0000:02:00.0: L1 Enabled - LTR Enabled [ 3.157046] iwlwifi 0000:02:00.0: L1 Enabled - LTR Enabled [ 3.157206] iwlwifi 0000:02:00.0: L1 Enabled - LTR Enabled [ 3.163194] IPv6: ADDRCONF(NETDEV_UP): wlp2s0: link is not ready [ 3.165985] IPv6: ADDRCONF(NETDEV_UP): enp1s0: link is not ready [ 3.189099] IPv6: ADDRCONF(NETDEV_UP): enp1s0: link is not ready [ 3.221023] asix 1-2.4:1.0 eth0: register 'asix' at usb-0000:00:15.0-2.4, ASIX AX88772 USB 2.0 Ethernet, 00:10:60:31:c2:a7 [ 3.221039] usbcore: registered new interface driver asix [ 3.223228] asix 1-2.4:1.0 enx00106031c2a7: renamed from eth0 [ 3.247947] asix 1-2.4:1.0 enx00106031c2a7: link down [ 3.248148] IPv6: ADDRCONF(NETDEV_UP): enx00106031c2a7: link is not ready [ 3.262741] IPv6: ADDRCONF(NETDEV_UP): wlp2s0: link is not ready [ 3.651026] IPv6: ADDRCONF(NETDEV_CHANGE): enx00106031c2a7: link becomes ready [ 3.651139] asix 1-2.4:1.0 enx00106031c2a7: link up, 100Mbps, full-duplex, lpa 0xC5E1 [ 6.528936] [drm:skl_update_scaler_plane] Updating scaler for [PLANE:23:plane 1A] scaler_user index 0.0 [ 20.412433] gem_exec_suspend: executing [ 20.412514] [drm:i915_gem_open] [ 20.412588] [drm:i915_gem_object_create_stolen] creating stolen object: size=4000 [ 20.412591] [drm:i915_pages_create_for_stolen] offset=0x7fa000, size=16384 [ 20.412673] [drm:i915_gem_object_create_stolen] creating stolen object: size=4000 [ 20.412675] [drm:i915_pages_create_for_stolen] offset=0x7fe000, size=16384 [ 20.412703] [drm:i915_gem_object_create_stolen] creating stolen object: size=4000 [ 20.412705] [drm:i915_pages_create_for_stolen] offset=0x802000, size=16384 [ 20.412716] [drm:i915_gem_object_create_stolen] creating stolen object: size=4000 [ 20.412718] [drm:i915_pages_create_for_stolen] offset=0x806000, size=16384 [ 20.412993] [drm:i915_gem_open] [ 20.413314] [drm:i915_gem_object_create_stolen] creating stolen object: size=4000 [ 20.413316] [drm:i915_pages_create_for_stolen] offset=0x80a000, size=16384 [ 20.413365] [drm:i915_gem_object_create_stolen] creating stolen object: size=4000 [ 20.413368] [drm:i915_pages_create_for_stolen] offset=0x80e000, size=16384 [ 20.413386] [drm:i915_gem_object_create_stolen] creating stolen object: size=4000 [ 20.413388] [drm:i915_pages_create_for_stolen] offset=0x812000, size=16384 [ 20.413399] [drm:i915_gem_object_create_stolen] creating stolen object: size=4000 [ 20.413401] [drm:i915_pages_create_for_stolen] offset=0x816000, size=16384 [ 20.413609] [drm:skl_update_scaler_plane] Updating scaler for [PLANE:23:plane 1A] scaler_user index 0.0 [ 21.486471] gem_exec_suspend: executing [ 21.486514] [drm:i915_gem_open] [ 21.486586] [drm:i915_gem_object_create_stolen] creating stolen object: size=4000 [ 21.486588] [drm:i915_pages_create_for_stolen] offset=0x7fa000, size=16384 [ 21.486669] [drm:i915_gem_object_create_stolen] creating stolen object: size=4000 [ 21.486671] [drm:i915_pages_create_for_stolen] offset=0x7fe000, size=16384 [ 21.486685] [drm:i915_gem_object_create_stolen] creating stolen object: size=4000 [ 21.486687] [drm:i915_pages_create_for_stolen] offset=0x802000, size=16384 [ 21.486699] [drm:i915_gem_object_create_stolen] creating stolen object: size=4000 [ 21.486700] [drm:i915_pages_create_for_stolen] offset=0x806000, size=16384 [ 21.486990] [drm:i915_gem_open] [ 21.487124] gem_exec_suspend: starting subtest default-uncached-S4 [ 21.556538] PM: Syncing filesystems ... done. [ 21.561734] Freezing user space processes ... (elapsed 0.016 seconds) done. [ 21.565795] Double checking all user space processes after OOM killer disable... (elapsed 0.001 seconds) [ 21.568936] PM: Marking nosave pages: [mem 0x00000000-0x00000fff] [ 21.568997] PM: Marking nosave pages: [mem 0x00058000-0x00058fff] [ 21.569023] PM: Marking nosave pages: [mem 0x0009e000-0x000fffff] [ 21.569050] PM: Marking nosave pages: [mem 0x0f000000-0x12151fff] [ 21.571142] PM: Marking nosave pages: [mem 0x77fde000-0x79e2dfff] [ 21.572540] PM: Marking nosave pages: [mem 0x7ac27000-0x7ac51fff] [ 21.572566] PM: Marking nosave pages: [mem 0x7b000000-0xffffffff] [ 21.590177] PM: Basic memory bitmaps created [ 21.590260] PM: Preallocating image memory... done (allocated 157652 pages) [ 21.738853] PM: Allocated 630608 kbytes in 0.62 seconds (1017.10 MB/s) [ 21.738855] Freezing remaining freezable tasks ... (elapsed 0.011 seconds) done. [ 21.764327] hpet_rtc_timer_reinit: 33 callbacks suppressed [ 21.764328] hpet1: lost 7160 rtc interrupts [ 22.003767] hpet1: lost 7161 rtc interrupts [ 22.243880] hpet1: lost 7161 rtc interrupts [ 22.485524] hpet1: lost 7161 rtc interrupts [ 22.707062] hpet1: lost 7161 rtc interrupts [ 22.947477] hpet1: lost 7161 rtc interrupts [ 23.186630] hpet1: lost 7161 rtc interrupts [ 23.425113] hpet1: lost 7161 rtc interrupts [ 23.665032] hpet1: lost 7161 rtc interrupts [ 23.905963] hpet1: lost 7161 rtc interrupts [ 24.076466] Suspending console(s) (use no_console_suspend to debug) [ 24.078150] [drm:intel_power_well_enable] enabling DC off [ 24.078153] [drm:gen9_set_dc_state] Setting DC state from 01 to 00 [ 24.078162] [drm:intel_power_well_enable] enabling power well 2 [ 24.078163] [drm:skl_set_power_well] Enabling power well 2 [ 24.080637] [drm:intel_power_well_enable] enabling dpio-common-bc [ 24.080769] [drm:connected_sink_compute_bpp] [CONNECTOR:39:eDP-1] checking for sink bpp constrains [ 24.080770] [drm:connected_sink_compute_bpp] clamping display bpp (was 36) to EDID reported max of 24 [ 24.080772] [drm:skl_update_scaler_crtc] Updating scaler for [CRTC:26:pipe A] scaler_user index 0.31 [ 24.080772] [drm:intel_dp_compute_config] DP link computation with max lane count 2 max bw 270000 pixel clock 138120KHz [ 24.080775] [drm:intel_dp_compute_config] DP link bw 0a rate select 00 lane count 2 clock 270000 bpp 24 [ 24.080775] [drm:intel_dp_compute_config] DP link bw required 331488 available 432000 [ 24.080776] [drm:intel_modeset_pipe_config] hw max bpp: 36, pipe bpp: 24, dithering: 0 [ 24.080777] [drm:intel_dump_pipe_config] [CRTC:26:pipe A][modeset] config ffff88046c074000 for pipe A [ 24.080777] [drm:intel_dump_pipe_config] cpu_transcoder: EDP [ 24.080778] [drm:intel_dump_pipe_config] pipe bpp: 24, dithering: 0 [ 24.080778] [drm:intel_dump_pipe_config] fdi/pch: 0, lanes: 0, gmch_m: 0, gmch_n: 0, link_m: 0, link_n: 0, tu: 0 [ 24.080779] [drm:intel_dump_pipe_config] dp: 1, lanes: 2, gmch_m: 6436858, gmch_n: 8388608, link_m: 268202, link_n: 524288, tu: 64 [ 24.080780] [drm:intel_dump_pipe_config] dp: 1, lanes: 2, gmch_m2: 0, gmch_n2: 0, link_m2: 0, link_n2: 0, tu2: 0 [ 24.080780] [drm:intel_dump_pipe_config] audio: 0, infoframes: 0 [ 24.080781] [drm:intel_dump_pipe_config] requested mode: [ 24.080782] [drm:drm_mode_debug_printmodeline] Modeline 0:"1920x1080" 60 138120 1920 1968 2018 2052 1080 1084 1086 1122 0x48 0xa [ 24.080782] [drm:intel_dump_pipe_config] adjusted mode: [ 24.080783] [drm:drm_mode_debug_printmodeline] Modeline 0:"1920x1080" 60 138120 1920 1968 2018 2052 1080 1084 1086 1122 0x48 0xa [ 24.080784] [drm:intel_dump_crtc_timings] crtc timings: 138120 1920 1968 2018 2052 1080 1084 1086 1122, type: 0x48 flags: 0xa [ 24.080785] [drm:intel_dump_pipe_config] port clock: 270000 [ 24.080785] [drm:intel_dump_pipe_config] pipe src size: 1920x1080 [ 24.080785] [drm:intel_dump_pipe_config] num_scalers: 2, scaler_users: 0x0, scaler_id: -1 [ 24.080786] [drm:intel_dump_pipe_config] gmch pfit: control: 0x00000000, ratios: 0x00000000, lvds border: 0x00000000 [ 24.080787] [drm:intel_dump_pipe_config] pch pfit: pos: 0x00000000, size: 0x00000000, disabled [ 24.080787] [drm:intel_dump_pipe_config] ips: 0 [ 24.080787] [drm:intel_dump_pipe_config] double wide: 0 [ 24.080788] [drm:intel_dump_pipe_config] ddi_pll_sel: 0; dpll_hw_state: ebb0: 0x8100, ebb4: 0x2000,pll0: 0x1b, pll1: 0x100, pll2: 0x0, pll3: 0x0, pll6: 0x10803, pll8: 0x9, pll9: 0xa, pll10: 0x8003c00, pcsdw12: 0x4d [ 24.080789] [drm:intel_dump_pipe_config] planes on this crtc [ 24.080790] [drm:intel_dump_pipe_config] [PLANE:23:plane 1A] enabled [ 24.080791] [drm:intel_dump_pipe_config] FB:60, fb = 1920x1080 format = XR24 little-endian (0x34325258) [ 24.080791] [drm:intel_dump_pipe_config] scaler:-1 src 0x0+1920+1080 dst 0x0+1920+1080 [ 24.080792] [drm:intel_dump_pipe_config] [PLANE:25:cursor A] disabled, scaler_id = -1 [ 24.080792] [drm:intel_dump_pipe_config] [PLANE:27:plane 2A] disabled, scaler_id = -1 [ 24.080793] [drm:intel_dump_pipe_config] [PLANE:28:plane 3A] disabled, scaler_id = -1 [ 24.080794] [drm:intel_modeset_checks] New cdclk calculated to be atomic 144000, actual 144000 [ 24.080796] [drm:skl_update_scaler_plane] Updating scaler for [PLANE:23:plane 1A] scaler_user index 0.0 [ 24.080797] [drm:bxt_get_dpll] [CRTC:26:pipe A] using pre-allocated PORT PLL A [ 24.080798] [drm:intel_reference_shared_dpll] using PORT PLL A for pipe A [ 24.080798] [drm:skl_update_scaler_crtc] Updating scaler for [CRTC:26:pipe A] scaler_user index 0.31 [ 24.080807] [drm:intel_edp_backlight_off] [ 24.092117] igb 0000:01:00.0: System wakeup enabled by ACPI [ 24.150799] hpet1: lost 7161 rtc interrupts [ 24.157239] [drm:intel_panel_actually_set_backlight] set backlight PWM = 0 [ 24.157245] [drm:intel_disable_pipe] disabling pipe A [ 24.161272] [drm:edp_panel_vdd_on] Turning eDP port A VDD on [ 24.161273] [drm:edp_panel_vdd_on] PP_STATUS: 0x80000008 PP_CONTROL: 0x0000006b [ 24.161318] [drm:edp_panel_off] Turn eDP port A panel power off [ 24.161320] [drm:wait_panel_off] Wait for panel power off time [ 24.161321] [drm:wait_panel_status] mask b0000000 value 00000000 status 80000008 control 00000060 [ 24.173342] [drm:wait_panel_status] Wait complete [ 24.173344] [drm:intel_disable_shared_dpll] disable PORT PLL A (active 1, on? 1) for crtc 26 [ 24.173349] [drm:intel_disable_shared_dpll] disabling PORT PLL A [ 24.173351] [drm:verify_encoder_state] [ENCODER:38:DDI A] [ 24.173352] [drm:verify_encoder_state] [ENCODER:46:DDI B] [ 24.173353] [drm:verify_encoder_state] [ENCODER:48:DP-MST A] [ 24.173353] [drm:verify_encoder_state] [ENCODER:49:DP-MST B] [ 24.173354] [drm:verify_encoder_state] [ENCODER:50:DP-MST C] [ 24.173354] [drm:verify_encoder_state] [ENCODER:53:DDI C] [ 24.173355] [drm:verify_encoder_state] [ENCODER:55:DP-MST A] [ 24.173355] [drm:verify_encoder_state] [ENCODER:56:DP-MST B] [ 24.173356] [drm:verify_encoder_state] [ENCODER:57:DP-MST C] [ 24.173356] [drm:intel_connector_verify_state] [CONNECTOR:47:DP-1] [ 24.173357] [drm:intel_connector_verify_state] [CONNECTOR:51:HDMI-A-1] [ 24.173358] [drm:intel_connector_verify_state] [CONNECTOR:54:DP-2] [ 24.173359] [drm:intel_connector_verify_state] [CONNECTOR:58:HDMI-A-2] [ 24.173360] [drm:verify_single_dpll_state] PORT PLL A [ 24.173360] [drm:verify_single_dpll_state] PORT PLL B [ 24.173361] [drm:verify_single_dpll_state] PORT PLL C [ 24.173363] [drm:intel_connector_verify_state] [CONNECTOR:39:eDP-1] [ 24.173365] [drm:verify_crtc_state] [CRTC:26:pipe A] [ 24.173367] [drm:verify_single_dpll_state] PORT PLL A [ 24.173435] [drm:intel_power_well_disable] disabling dpio-common-bc [ 24.173436] [drm:intel_power_well_disable] disabling dpio-common-a [ 24.173436] [drm:intel_power_well_disable] disabling power well 2 [ 24.173439] [drm:skl_set_power_well] Disabling power well 2 [ 24.173440] [drm:intel_power_well_disable] disabling DC off [ 24.173441] [drm:gen9_enable_dc5] Enabling DC5 [ 24.173442] [drm:gen9_set_dc_state] Setting DC state from 00 to 01 [ 24.173443] [drm:intel_power_well_disable] disabling always-on [ 24.173468] PM: freeze of devices complete after 405.429 msecs [ 24.173705] [drm:gen9_set_dc_state] Setting DC state from 01 to 00 [ 24.173718] [drm:bxt_set_cdclk] Changing CDCLK to 19200 kHz (VCO 0 kHz) [ 24.177743] [drm:intel_update_cdclk] Current CD clock rate: 19200 kHz, VCO: 0 kHz, ref: 19200 kHz [ 24.177744] [drm:intel_power_well_disable] disabling power well 1 [ 24.177746] [drm:skl_set_power_well] Disabling power well 1 [ 24.177748] [drm:gen9_sanitize_power_well_requests] Clearing auxiliary requests for power well 1 forced on by DMC [ 24.177750] [drm:bxt_enable_dc9] Enabling DC9 [ 24.177751] [drm:gen9_set_dc_state] Setting DC state from 00 to 08 [ 24.191537] PM: late freeze of devices complete after 75.510 msecs [ 24.202859] PM: noirq freeze of devices complete after 47.309 msecs [ 24.202927] ACPI: Preparing to enter system sleep state S4 [ 24.203143] ACPI : EC: EC stopped [ 24.203143] PM: Saving platform NVS memory [ 24.203307] Disabling non-boot CPUs ... [ 24.203523] Broke affinity for irq 128 [ 24.203524] Broke affinity for irq 130 [ 24.204554] smpboot: CPU 1 is now offline [ 24.211530] Broke affinity for irq 128 [ 24.211531] Broke affinity for irq 130 [ 24.212551] smpboot: CPU 2 is now offline [ 24.221856] Broke affinity for irq 8 [ 24.221857] Broke affinity for irq 9 [ 24.221887] Broke affinity for irq 39 [ 24.221892] Broke affinity for irq 122 [ 24.221893] Broke affinity for irq 128 [ 24.221894] Broke affinity for irq 129 [ 24.221894] Broke affinity for irq 130 [ 24.222903] smpboot: CPU 3 is now offline [ 24.228826] PM: Creating hibernation image: [ 24.424701] PM: Need to copy 156026 pages [ 24.424702] PM: Normal pages needed: 156026 + 1024, available pages: 3996967 [ 24.228997] PM: Restoring platform NVS memory [ 24.229033] ACPI : EC: EC started [ 24.229379] Enabling non-boot CPUs ... [ 24.236169] x86: Booting SMP configuration: [ 24.236170] smpboot: Booting Node 0 Processor 1 APIC 0x2 [ 24.238381] cache: parent cpu1 should not be sleeping [ 24.238529] CPU1 is up [ 24.246551] smpboot: Booting Node 0 Processor 2 APIC 0x4 [ 24.248755] cache: parent cpu2 should not be sleeping [ 24.248916] CPU2 is up [ 24.260568] smpboot: Booting Node 0 Processor 3 APIC 0x6 [ 24.262777] cache: parent cpu3 should not be sleeping [ 24.262958] CPU3 is up [ 24.263594] ACPI: Waking up from system sleep state S4 [ 24.271659] acpi LNXPOWER:14: Turning OFF [ 24.296561] PM: noirq restore of devices complete after 101.314 msecs [ 24.296625] [drm:gen9_sanitize_dc_state] Resetting DC state tracking from 08 to 08 [ 24.296626] [drm:bxt_disable_dc9] Disabling DC9 [ 24.296626] [drm:gen9_set_dc_state] Setting DC state from 08 to 00 [ 24.296630] [drm:bxt_check_bios_rc6_setup] BIOS enabled RC states: HW_CTRL on HW_RC6 on SW_TARGET_STATE 0 [ 24.296675] [drm:gen9_set_dc_state] Setting DC state from 00 to 00 [ 24.296678] [drm:intel_power_well_enable] enabling power well 1 [ 24.296680] [drm:skl_set_power_well] Enabling power well 1 [ 24.298223] [drm:intel_update_cdclk] Current CD clock rate: 19200 kHz, VCO: 0 kHz, ref: 19200 kHz [ 24.298224] [drm:bxt_sanitize_cdclk] Sanitizing cdclk programmed by pre-os [ 24.298224] [drm:bxt_set_cdclk] Changing CDCLK to 144000 kHz (VCO 1152000 kHz) [ 24.302242] [drm:intel_update_cdclk] Current CD clock rate: 144000 kHz, VCO: 1152000 kHz, ref: 19200 kHz [ 24.302336] [drm:intel_power_well_enable] enabling always-on [ 24.302336] [drm:intel_power_well_enable] enabling DC off [ 24.302337] [drm:gen9_set_dc_state] Setting DC state from 00 to 00 [ 24.302339] [drm:intel_power_well_enable] enabling power well 2 [ 24.302339] [drm:skl_set_power_well] Enabling power well 2 [ 24.304346] [drm:intel_power_well_enable] enabling dpio-common-a [ 24.306385] [drm:intel_power_well_enable] enabling dpio-common-bc [ 24.306415] [drm:gen9_set_dc_state] Setting DC state from 00 to 00 [ 24.306431] [drm:bxt_ddi_phy_init] DDI PHY 1 already enabled, won't reprogram it [ 24.306440] [drm:bxt_ddi_phy_init] DDI PHY 0 already enabled, won't reprogram it [ 24.306477] PM: early restore of devices complete after 41.362 msecs [ 24.351604] usb usb1: root hub lost power or was reset [ 24.351605] usb usb2: root hub lost power or was reset [ 24.351645] [drm:intel_opregion_setup] graphic opregion physical addr: 0x79dd7018 [ 24.351655] [drm:intel_opregion_setup] Public ACPI methods supported [ 24.351655] [drm:intel_opregion_setup] ASLE supported [ 24.351658] [drm:intel_opregion_setup] Found valid VBT in ACPI OpRegion (RVDA) [ 24.351661] [drm:intel_dp_init_panel_power_sequencer_registers] panel power sequencer register settings: PP_ON 0x7d00001, PP_OFF 0x1f40001, PP_DIV 0x60 [ 24.351675] [drm:gen8_init_common_ring] Execlists enabled for render ring [ 24.351678] igb 0000:01:00.0: System wakeup disabled by ACPI [ 24.351700] [drm:gen8_init_common_ring] Execlists enabled for blitter ring [ 24.351721] [drm:gen8_init_common_ring] Execlists enabled for bsd ring [ 24.351742] [drm:gen8_init_common_ring] Execlists enabled for video enhancement ring [ 24.351762] [drm:intel_guc_setup] GuC fw status: path i915/bxt_guc_ver8_7.bin, fetch SUCCESS, load SUCCESS [ 24.351765] [drm:intel_guc_setup] GuC fw status: fetch SUCCESS, load PENDING [ 24.351946] rtc_cmos 00:04: System wakeup disabled by ACPI [ 24.355561] [drm:guc_ucode_xfer_dma] DMA status 0x10, GuC status 0x8002f0ec [ 24.355562] [drm:guc_ucode_xfer_dma] returning 0 [ 24.355563] [drm:intel_guc_setup] GuC fw status: fetch SUCCESS, load SUCCESS [ 24.355576] [drm:select_doorbell_register] assigned normal priority doorbell id 0x0 [ 24.355577] [drm:select_doorbell_cacheline] selected doorbell cacheline 0x40, next 0x80, linesize 64 [ 24.357656] [drm:guc_client_alloc] new priority 2 client ffff88007aa24900: ctx_index 0 [ 24.357657] [drm:guc_client_alloc] doorbell id 0, cacheline offset 0x40 [ 24.362844] [drm:intel_update_cdclk] Current CD clock rate: 144000 kHz, VCO: 1152000 kHz, ref: 19200 kHz [ 24.362849] [drm:bxt_hpd_irq_setup] Invert bit setting: hp_ctl:18001818 hp_port:38 [ 24.362854] [drm:intel_modeset_readout_hw_state] [CRTC:26:pipe A] hw state readout: disabled [ 24.362855] [drm:intel_modeset_readout_hw_state] [CRTC:31:pipe B] hw state readout: disabled [ 24.362857] [drm:intel_modeset_readout_hw_state] [CRTC:36:pipe C] hw state readout: disabled [ 24.362858] [drm:intel_modeset_readout_hw_state] PORT PLL A hw state readout: crtc_mask 0x00000000, on 0 [ 24.362859] [drm:intel_modeset_readout_hw_state] PORT PLL B hw state readout: crtc_mask 0x00000000, on 0 [ 24.362859] [drm:intel_modeset_readout_hw_state] PORT PLL C hw state readout: crtc_mask 0x00000000, on 0 [ 24.362861] [drm:intel_modeset_readout_hw_state] [ENCODER:38:DDI A] hw state readout: disabled, pipe A [ 24.362861] [drm:intel_modeset_readout_hw_state] [ENCODER:46:DDI B] hw state readout: disabled, pipe A [ 24.362862] [drm:intel_modeset_readout_hw_state] [ENCODER:48:DP-MST A] hw state readout: disabled, pipe A [ 24.362863] [drm:intel_modeset_readout_hw_state] [ENCODER:49:DP-MST B] hw state readout: disabled, pipe B [ 24.362863] [drm:intel_modeset_readout_hw_state] [ENCODER:50:DP-MST C] hw state readout: disabled, pipe C [ 24.362864] [drm:intel_modeset_readout_hw_state] [ENCODER:53:DDI C] hw state readout: disabled, pipe A [ 24.362864] [drm:intel_modeset_readout_hw_state] [ENCODER:55:DP-MST A] hw state readout: disabled, pipe A [ 24.362865] [drm:intel_modeset_readout_hw_state] [ENCODER:56:DP-MST B] hw state readout: disabled, pipe B [ 24.362865] [drm:intel_modeset_readout_hw_state] [ENCODER:57:DP-MST C] hw state readout: disabled, pipe C [ 24.362866] [drm:intel_modeset_readout_hw_state] [CONNECTOR:39:eDP-1] hw state readout: disabled [ 24.362867] [drm:intel_modeset_readout_hw_state] [CONNECTOR:47:DP-1] hw state readout: disabled [ 24.362868] [drm:intel_modeset_readout_hw_state] [CONNECTOR:51:HDMI-A-1] hw state readout: disabled [ 24.362869] [drm:intel_modeset_readout_hw_state] [CONNECTOR:54:DP-2] hw state readout: disabled [ 24.362870] [drm:intel_modeset_readout_hw_state] [CONNECTOR:58:HDMI-A-2] hw state readout: disabled [ 24.362872] [drm:intel_dump_pipe_config] [CRTC:26:pipe A][setup_hw_state] config ffff88046c074000 for pipe A [ 24.362872] [drm:intel_dump_pipe_config] cpu_transcoder: A [ 24.362873] [drm:intel_dump_pipe_config] pipe bpp: 0, dithering: 0 [ 24.362873] [drm:intel_dump_pipe_config] fdi/pch: 0, lanes: 0, gmch_m: 0, gmch_n: 0, link_m: 0, link_n: 0, tu: 0 [ 24.362874] [drm:intel_dump_pipe_config] dp: 0, lanes: 0, gmch_m: 0, gmch_n: 0, link_m: 0, link_n: 0, tu: 0 [ 24.362875] [drm:intel_dump_pipe_config] dp: 0, lanes: 0, gmch_m2: 0, gmch_n2: 0, link_m2: 0, link_n2: 0, tu2: 0 [ 24.362875] [drm:intel_dump_pipe_config] audio: 0, infoframes: 0 [ 24.362875] [drm:intel_dump_pipe_config] requested mode: [ 24.362877] [drm:drm_mode_debug_printmodeline] Modeline 0:"" 0 0 0 0 0 0 0 0 0 0 0x0 0x0 [ 24.362877] [drm:intel_dump_pipe_config] adjusted mode: [ 24.362878] [drm:drm_mode_debug_printmodeline] Modeline 0:"" 0 0 0 0 0 0 0 0 0 0 0x0 0x0 [ 24.362879] [drm:intel_dump_crtc_timings] crtc timings: 0 0 0 0 0 0 0 0 0, type: 0x0 flags: 0x0 [ 24.362879] [drm:intel_dump_pipe_config] port clock: 0 [ 24.362879] [drm:intel_dump_pipe_config] pipe src size: 0x0 [ 24.362880] [drm:intel_dump_pipe_config] num_scalers: 2, scaler_users: 0x0, scaler_id: 0 [ 24.362880] [drm:intel_dump_pipe_config] gmch pfit: control: 0x00000000, ratios: 0x00000000, lvds border: 0x00000000 [ 24.362881] [drm:intel_dump_pipe_config] pch pfit: pos: 0x00000000, size: 0x00000000, disabled [ 24.362881] [drm:intel_dump_pipe_config] ips: 0 [ 24.362882] [drm:intel_dump_pipe_config] double wide: 0 [ 24.362883] [drm:intel_dump_pipe_config] ddi_pll_sel: 0; dpll_hw_state: ebb0: 0x0, ebb4: 0x0,pll0: 0x0, pll1: 0x0, pll2: 0x0, pll3: 0x0, pll6: 0x0, pll8: 0x0, pll9: 0x0, pll10: 0x0, pcsdw12: 0x0 [ 24.362883] [drm:intel_dump_pipe_config] planes on this crtc [ 24.362885] [drm:intel_dump_pipe_config] [PLANE:23:plane 1A] enabled [ 24.362886] [drm:intel_dump_pipe_config] FB:60, fb = 1920x1080 format = XR24 little-endian (0x34325258) [ 24.362886] [drm:intel_dump_pipe_config] scaler:-1 src 0x0+1920+1080 dst 0x0+1920+1080 [ 24.362886] [drm:intel_dump_pipe_config] [PLANE:25:cursor A] disabled, scaler_id = -1 [ 24.362887] [drm:intel_dump_pipe_config] [PLANE:27:plane 2A] disabled, scaler_id = -1 [ 24.362887] [drm:intel_dump_pipe_config] [PLANE:28:plane 3A] disabled, scaler_id = -1 [ 24.362888] [drm:intel_dump_pipe_config] [CRTC:31:pipe B][setup_hw_state] config ffff88046c073000 for pipe B [ 24.362889] [drm:intel_dump_pipe_config] cpu_transcoder: B [ 24.362889] [drm:intel_dump_pipe_config] pipe bpp: 0, dithering: 0 [ 24.362890] [drm:intel_dump_pipe_config] fdi/pch: 0, lanes: 0, gmch_m: 0, gmch_n: 0, link_m: 0, link_n: 0, tu: 0 [ 24.362890] [drm:intel_dump_pipe_config] dp: 0, lanes: 0, gmch_m: 0, gmch_n: 0, link_m: 0, link_n: 0, tu: 0 [ 24.362891] [drm:intel_dump_pipe_config] dp: 0, lanes: 0, gmch_m2: 0, gmch_n2: 0, link_m2: 0, link_n2: 0, tu2: 0 [ 24.362891] [drm:intel_dump_pipe_config] audio: 0, infoframes: 0 [ 24.362892] [drm:intel_dump_pipe_config] requested mode: [ 24.362893] [drm:drm_mode_debug_printmodeline] Modeline 0:"" 0 0 0 0 0 0 0 0 0 0 0x0 0x0 [ 24.362893] [drm:intel_dump_pipe_config] adjusted mode: [ 24.362894] [drm:drm_mode_debug_printmodeline] Modeline 0:"" 0 0 0 0 0 0 0 0 0 0 0x0 0x0 [ 24.362896] [drm:intel_dump_crtc_timings] crtc timings: 0 0 0 0 0 0 0 0 0, type: 0x0 flags: 0x0 [ 24.362896] [drm:intel_dump_pipe_config] port clock: 0 [ 24.362896] [drm:intel_dump_pipe_config] pipe src size: 0x0 [ 24.362897] [drm:intel_dump_pipe_config] num_scalers: 2, scaler_users: 0x0, scaler_id: 0 [ 24.362897] [drm:intel_dump_pipe_config] gmch pfit: control: 0x00000000, ratios: 0x00000000, lvds border: 0x00000000 [ 24.362898] [drm:intel_dump_pipe_config] pch pfit: pos: 0x00000000, size: 0x00000000, disabled [ 24.362898] [drm:intel_dump_pipe_config] ips: 0 [ 24.362899] [drm:intel_dump_pipe_config] double wide: 0 [ 24.362899] [drm:intel_dump_pipe_config] ddi_pll_sel: 0; dpll_hw_state: ebb0: 0x0, ebb4: 0x0,pll0: 0x0, pll1: 0x0, pll2: 0x0, pll3: 0x0, pll6: 0x0, pll8: 0x0, pll9: 0x0, pll10: 0x0, pcsdw12: 0x0 [ 24.362900] [drm:intel_dump_pipe_config] planes on this crtc [ 24.362900] [drm:intel_dump_pipe_config] [PLANE:29:plane 1B] disabled, scaler_id = -1 [ 24.362901] [drm:intel_dump_pipe_config] [PLANE:30:cursor B] disabled, scaler_id = -1 [ 24.362901] [drm:intel_dump_pipe_config] [PLANE:32:plane 2B] disabled, scaler_id = -1 [ 24.362902] [drm:intel_dump_pipe_config] [PLANE:33:plane 3B] disabled, scaler_id = -1 [ 24.362903] [drm:intel_dump_pipe_config] [CRTC:36:pipe C][setup_hw_state] config ffff88046c072800 for pipe C [ 24.362903] [drm:intel_dump_pipe_config] cpu_transcoder: C [ 24.362903] [drm:intel_dump_pipe_config] pipe bpp: 0, dithering: 0 [ 24.362904] [drm:intel_dump_pipe_config] fdi/pch: 0, lanes: 0, gmch_m: 0, gmch_n: 0, link_m: 0, link_n: 0, tu: 0 [ 24.362905] [drm:intel_dump_pipe_config] dp: 0, lanes: 0, gmch_m: 0, gmch_n: 0, link_m: 0, link_n: 0, tu: 0 [ 24.362905] [drm:intel_dump_pipe_config] dp: 0, lanes: 0, gmch_m2: 0, gmch_n2: 0, link_m2: 0, link_n2: 0, tu2: 0 [ 24.362906] [drm:intel_dump_pipe_config] audio: 0, infoframes: 0 [ 24.362906] [drm:intel_dump_pipe_config] requested mode: [ 24.362907] [drm:drm_mode_debug_printmodeline] Modeline 0:"" 0 0 0 0 0 0 0 0 0 0 0x0 0x0 [ 24.362907] [drm:intel_dump_pipe_config] adjusted mode: [ 24.362908] [drm:drm_mode_debug_printmodeline] Modeline 0:"" 0 0 0 0 0 0 0 0 0 0 0x0 0x0 [ 24.362909] [drm:intel_dump_crtc_timings] crtc timings: 0 0 0 0 0 0 0 0 0, type: 0x0 flags: 0x0 [ 24.362909] [drm:intel_dump_pipe_config] port clock: 0 [ 24.362910] [drm:intel_dump_pipe_config] pipe src size: 0x0 [ 24.362910] [drm:intel_dump_pipe_config] num_scalers: 1, scaler_users: 0x0, scaler_id: 0 [ 24.362911] [drm:intel_dump_pipe_config] gmch pfit: control: 0x00000000, ratios: 0x00000000, lvds border: 0x00000000 [ 24.362911] [drm:intel_dump_pipe_config] pch pfit: pos: 0x00000000, size: 0x00000000, disabled [ 24.362911] [drm:intel_dump_pipe_config] ips: 0 [ 24.362912] [drm:intel_dump_pipe_config] double wide: 0 [ 24.362913] [drm:intel_dump_pipe_config] ddi_pll_sel: 0; dpll_hw_state: ebb0: 0x0, ebb4: 0x0,pll0: 0x0, pll1: 0x0, pll2: 0x0, pll3: 0x0, pll6: 0x0, pll8: 0x0, pll9: 0x0, pll10: 0x0, pcsdw12: 0x0 [ 24.362913] [drm:intel_dump_pipe_config] planes on this crtc [ 24.362913] [drm:intel_dump_pipe_config] [PLANE:34:plane 1C] disabled, scaler_id = -1 [ 24.362914] [drm:intel_dump_pipe_config] [PLANE:35:cursor C] disabled, scaler_id = -1 [ 24.362914] [drm:intel_dump_pipe_config] [PLANE:37:plane 2C] disabled, scaler_id = -1 [ 24.362929] [drm:intel_power_well_disable] disabling dpio-common-bc [ 24.362930] [drm:intel_power_well_disable] disabling dpio-common-a [ 24.362931] [drm:intel_power_well_disable] disabling power well 2 [ 24.362934] [drm:skl_set_power_well] Disabling power well 2 [ 24.362934] [drm:intel_power_well_disable] disabling DC off [ 24.362936] [drm:gen9_enable_dc5] Enabling DC5 [ 24.362936] [drm:gen9_set_dc_state] Setting DC state from 00 to 01 [ 24.362937] [drm:intel_power_well_disable] disabling always-on [ 24.362942] [drm:connected_sink_compute_bpp] [CONNECTOR:39:eDP-1] checking for sink bpp constrains [ 24.362942] [drm:connected_sink_compute_bpp] clamping display bpp (was 36) to EDID reported max of 24 [ 24.362944] [drm:skl_update_scaler_crtc] Updating scaler for [CRTC:26:pipe A] scaler_user index 0.31 [ 24.362945] [drm:intel_dp_compute_config] DP link computation with max lane count 2 max bw 270000 pixel clock 138120KHz [ 24.362947] [drm:intel_dp_compute_config] DP link bw 0a rate select 00 lane count 2 clock 270000 bpp 24 [ 24.362947] [drm:intel_dp_compute_config] DP link bw required 331488 available 432000 [ 24.362948] [drm:intel_modeset_pipe_config] hw max bpp: 36, pipe bpp: 24, dithering: 0 [ 24.362949] [drm:intel_dump_pipe_config] [CRTC:26:pipe A][modeset] config ffff88046c076000 for pipe A [ 24.362949] [drm:intel_dump_pipe_config] cpu_transcoder: EDP [ 24.362950] [drm:intel_dump_pipe_config] pipe bpp: 24, dithering: 0 [ 24.362950] [drm:intel_dump_pipe_config] fdi/pch: 0, lanes: 0, gmch_m: 0, gmch_n: 0, link_m: 0, link_n: 0, tu: 0 [ 24.362951] [drm:intel_dump_pipe_config] dp: 1, lanes: 2, gmch_m: 6436858, gmch_n: 8388608, link_m: 268202, link_n: 524288, tu: 64 [ 24.362952] [drm:intel_dump_pipe_config] dp: 1, lanes: 2, gmch_m2: 0, gmch_n2: 0, link_m2: 0, link_n2: 0, tu2: 0 [ 24.362952] [drm:intel_dump_pipe_config] audio: 0, infoframes: 0 [ 24.362953] [drm:intel_dump_pipe_config] requested mode: [ 24.362954] [drm:drm_mode_debug_printmodeline] Modeline 0:"1920x1080" 60 138120 1920 1968 2018 2052 1080 1084 1086 1122 0x48 0xa [ 24.362954] [drm:intel_dump_pipe_config] adjusted mode: [ 24.362955] [drm:drm_mode_debug_printmodeline] Modeline 0:"1920x1080" 60 138120 1920 1968 2018 2052 1080 1084 1086 1122 0x48 0xa [ 24.362956] [drm:intel_dump_crtc_timings] crtc timings: 138120 1920 1968 2018 2052 1080 1084 1086 1122, type: 0x48 flags: 0xa [ 24.362956] [drm:intel_dump_pipe_config] port clock: 270000 [ 24.362957] [drm:intel_dump_pipe_config] pipe src size: 1920x1080 [ 24.362957] [drm:intel_dump_pipe_config] num_scalers: 2, scaler_users: 0x0, scaler_id: -1 [ 24.362958] [drm:intel_dump_pipe_config] gmch pfit: control: 0x00000000, ratios: 0x00000000, lvds border: 0x00000000 [ 24.362958] [drm:intel_dump_pipe_config] pch pfit: pos: 0x00000000, size: 0x00000000, disabled [ 24.362959] [drm:intel_dump_pipe_config] ips: 0 [ 24.362959] [drm:intel_dump_pipe_config] double wide: 0 [ 24.362960] [drm:intel_dump_pipe_config] ddi_pll_sel: 0; dpll_hw_state: ebb0: 0x8100, ebb4: 0x2000,pll0: 0x1b, pll1: 0x100, pll2: 0x0, pll3: 0x0, pll6: 0x10803, pll8: 0x9, pll9: 0xa, pll10: 0x8003c00, pcsdw12: 0x4d [ 24.362960] [drm:intel_dump_pipe_config] planes on this crtc [ 24.362962] [drm:intel_dump_pipe_config] [PLANE:23:plane 1A] enabled [ 24.362962] [drm:intel_dump_pipe_config] FB:60, fb = 1920x1080 format = XR24 little-endian (0x34325258) [ 24.362962] [drm:intel_dump_pipe_config] scaler:-1 src 0x0+1920+1080 dst 0x0+1920+1080 [ 24.362963] [drm:intel_dump_pipe_config] [PLANE:25:cursor A] disabled, scaler_id = -1 [ 24.362963] [drm:intel_dump_pipe_config] [PLANE:27:plane 2A] disabled, scaler_id = -1 [ 24.362964] [drm:intel_dump_pipe_config] [PLANE:28:plane 3A] disabled, scaler_id = -1 [ 24.362965] [drm:intel_modeset_checks] New cdclk calculated to be atomic 144000, actual 144000 [ 24.362967] [drm:skl_update_scaler_plane] Updating scaler for [PLANE:23:plane 1A] scaler_user index 0.0 [ 24.362968] [drm:bxt_get_dpll] [CRTC:26:pipe A] using pre-allocated PORT PLL A [ 24.362969] [drm:intel_reference_shared_dpll] using PORT PLL A for pipe A [ 24.362969] [drm:skl_update_scaler_crtc] Updating scaler for [CRTC:26:pipe A] scaler_user index 0.31 [ 24.362970] [drm:skl_update_scaler_crtc] Updating scaler for [CRTC:31:pipe B] scaler_user index 1.31 [ 24.362971] [drm:skl_update_scaler] scaler_user index 1.31: Staged freeing scaler id 0 scaler_users = 0x0 [ 24.362971] [drm:skl_update_scaler_crtc] Updating scaler for [CRTC:36:pipe C] scaler_user index 2.31 [ 24.362972] [drm:skl_update_scaler] scaler_user index 2.31: Staged freeing scaler id 0 scaler_users = 0x0 [ 24.362980] [drm:intel_power_well_enable] enabling always-on [ 24.362980] [drm:intel_power_well_enable] enabling DC off [ 24.363058] [drm:gen9_set_dc_state] Setting DC state from 01 to 00 [ 24.363060] [drm:intel_power_well_enable] enabling dpio-common-a [ 24.364091] [drm:verify_encoder_state] [ENCODER:38:DDI A] [ 24.364091] [drm:verify_encoder_state] [ENCODER:46:DDI B] [ 24.364092] [drm:verify_encoder_state] [ENCODER:48:DP-MST A] [ 24.364092] [drm:verify_encoder_state] [ENCODER:49:DP-MST B] [ 24.364093] [drm:verify_encoder_state] [ENCODER:50:DP-MST C] [ 24.364093] [drm:verify_encoder_state] [ENCODER:53:DDI C] [ 24.364094] [drm:verify_encoder_state] [ENCODER:55:DP-MST A] [ 24.364094] [drm:verify_encoder_state] [ENCODER:56:DP-MST B] [ 24.364094] [drm:verify_encoder_state] [ENCODER:57:DP-MST C] [ 24.364095] [drm:intel_connector_verify_state] [CONNECTOR:47:DP-1] [ 24.364095] [drm:intel_connector_verify_state] [CONNECTOR:51:HDMI-A-1] [ 24.364096] [drm:intel_connector_verify_state] [CONNECTOR:54:DP-2] [ 24.364096] [drm:intel_connector_verify_state] [CONNECTOR:58:HDMI-A-2] [ 24.364097] [drm:verify_single_dpll_state] PORT PLL A [ 24.364098] [drm:verify_single_dpll_state] PORT PLL B [ 24.364098] [drm:verify_single_dpll_state] PORT PLL C [ 24.364103] [drm:intel_enable_shared_dpll] enable PORT PLL A (active 1, on? 0) for crtc 26 [ 24.364103] [drm:intel_enable_shared_dpll] enabling PORT PLL A [ 24.364140] [drm:edp_panel_on] Turn eDP port A panel power on [ 24.364141] [drm:wait_panel_power_cycle] Wait for panel power cycle [ 24.364143] [drm:wait_panel_status] mask b800000f value 00000000 status 00000000 control 00000060 [ 24.364144] [drm:wait_panel_status] Wait complete [ 24.364144] [drm:wait_panel_on] Wait for panel power on [ 24.364145] [drm:wait_panel_status] mask b000000f value 80000008 status 0000000a control 00000063 [ 24.367961] [drm:intel_power_well_enable] enabling power well 2 [ 24.367962] [drm:skl_set_power_well] Enabling power well 2 [ 24.370437] sd 0:0:0:0: [sda] Starting disk [ 24.381680] iwlwifi 0000:02:00.0: L1 Enabled - LTR Enabled [ 24.381870] iwlwifi 0000:02:00.0: L1 Enabled - LTR Enabled [ 24.389896] [drm:intel_get_hpd_pins] hotplug event received, stat 0x00000008, dig 0x1a001818, pins 0x00000010 [ 24.389897] [drm:intel_hpd_irq_handler] digital hpd port A - long [ 24.389898] [drm:intel_hpd_irq_storm_detect] Received HPD interrupt on PIN 4 - cnt: 0 [ 24.389905] [drm:intel_dp_hpd_pulse] ignoring long hpd on eDP port A [ 24.404180] iwlwifi 0000:02:00.0: L1 Enabled - LTR Enabled [ 24.404714] iwlwifi 0000:02:00.0: L1 Enabled - LTR Enabled [ 24.412036] [drm:wait_panel_status] Wait complete [ 24.412039] [drm:edp_panel_vdd_on] Turning eDP port A VDD on [ 24.412040] [drm:edp_panel_vdd_on] PP_STATUS: 0x80000008 PP_CONTROL: 0x0000006b [ 24.412814] [drm:intel_dp_set_signal_levels] Using vswing level 0 [ 24.412815] [drm:intel_dp_set_signal_levels] Using pre-emphasis level 0 [ 24.413073] [drm:intel_dp_link_training_clock_recovery] clock recovery OK [ 24.413654] [drm:intel_dp_link_training_channel_equalization] Channel EQ done. DP Training successful [ 24.413711] [drm:skylake_pfit_enable] for crtc_state = ffff88046c076000 [ 24.413771] [drm:skl_wm_flush_pipe] flush pipe A (pass 3) [ 24.413772] [drm:intel_enable_pipe] enabling pipe A [ 24.413781] [drm:intel_edp_backlight_on] [ 24.413781] [drm:intel_panel_enable_backlight] pipe A [ 24.413782] [drm:intel_panel_actually_set_backlight] set backlight PWM = 96000 [ 24.413784] [drm:intel_psr_enable] PSR not supported on this platform [ 24.413784] [drm:intel_edp_drrs_enable] Panel doesn't support DRRS [ 24.417798] [drm:intel_connector_verify_state] [CONNECTOR:39:eDP-1] [ 24.417800] [drm:verify_crtc_state] [CRTC:26:pipe A] [ 24.417814] [drm:verify_single_dpll_state] PORT PLL A [ 24.417819] [drm:verify_crtc_state] [CRTC:31:pipe B] [ 24.417820] [drm:verify_crtc_state] [CRTC:36:pipe C] [ 24.417827] [drm:bxt_hpd_irq_setup] Invert bit setting: hp_ctl:18001818 hp_port:38 [ 24.417828] [drm:intel_dp_detect] [CONNECTOR:39:eDP-1] [ 24.417994] [drm:intel_dp_probe_oui] Sink OUI: 001cf8 [ 24.418124] [drm:intel_dp_probe_oui] Branch OUI: 000000 [ 24.418237] [drm:drm_helper_hpd_irq_event] [CONNECTOR:39:eDP-1] status updated from connected to connected [ 24.418237] [drm:intel_dp_detect] [CONNECTOR:47:DP-1] [ 24.418238] [drm:intel_power_well_enable] enabling dpio-common-bc [ 24.419056] [drm:intel_power_well_disable] disabling dpio-common-bc [ 24.419058] [drm:drm_helper_hpd_irq_event] [CONNECTOR:47:DP-1] status updated from disconnected to disconnected [ 24.419058] [drm:intel_hdmi_detect] [CONNECTOR:51:HDMI-A-1] [ 24.438032] usb 1-2: reset high-speed USB device number 2 using xhci_hcd [ 24.439900] atkbd serio0: Failed to deactivate keyboard on isa0060/serio0 [ 24.498270] [drm:intel_hdmi_detect] HDMI live status down [ 24.498272] [drm:drm_helper_hpd_irq_event] [CONNECTOR:51:HDMI-A-1] status updated from disconnected to disconnected [ 24.498272] [drm:intel_dp_detect] [CONNECTOR:54:DP-2] [ 24.498273] [drm:intel_power_well_enable] enabling dpio-common-bc [ 24.498306] [drm:intel_power_well_disable] disabling dpio-common-bc [ 24.498307] [drm:drm_helper_hpd_irq_event] [CONNECTOR:54:DP-2] status updated from disconnected to disconnected [ 24.498307] [drm:intel_hdmi_detect] [CONNECTOR:58:HDMI-A-2] [ 24.507728] atkbd serio0: Failed to enable keyboard on isa0060/serio0 [ 24.583124] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [ 24.584142] ata1.00: configured for UDMA/133 [ 24.584936] ata1.00: Enabling discard_zeroes_data [ 24.590505] [drm:intel_hdmi_detect] HDMI live status down [ 24.590506] [drm:drm_helper_hpd_irq_event] [CONNECTOR:58:HDMI-A-2] status updated from disconnected to disconnected [ 24.590789] [drm:intel_didl_outputs] More than 15 outputs detected via ACPI [ 24.595958] hpet1: lost 7161 rtc interrupts [ 24.647515] usb 1-7: reset full-speed USB device number 3 using xhci_hcd [ 24.648555] [drm] RC6 on [ 24.807297] usb 1-2.2: reset high-speed USB device number 4 using xhci_hcd [ 24.840520] hpet1: lost 7160 rtc interrupts [ 24.995581] usb 1-2.3: reset low-speed USB device number 5 using xhci_hcd [ 25.083845] hpet1: lost 7161 rtc interrupts [ 25.147526] [drm:edp_panel_vdd_off_sync] Turning eDP port A VDD off [ 25.147528] [drm:edp_panel_vdd_off_sync] PP_STATUS: 0x80000008 PP_CONTROL: 0x00000067 [ 25.289578] usb 1-2.4: reset high-speed USB device number 9 using xhci_hcd [ 25.327703] hpet1: lost 7161 rtc interrupts [ 25.376192] asix 1-2.4:1.0 enx00106031c2a7: unregister 'asix' usb-0000:00:15.0-2.4, ASIX AX88772 USB 2.0 Ethernet [ 25.439644] usb 1-2.2.4: reset low-speed USB device number 7 using xhci_hcd [ 25.571318] hpet1: lost 7161 rtc interrupts [ 25.731946] PM: restore of devices complete after 5769.895 msecs [ 25.732166] usb 1-2.4:1.0: rebind failed: -517 [ 25.732175] usb 1-7:1.0: rebind failed: -517 [ 25.732177] usb 1-7:1.1: rebind failed: -517 [ 25.732266] PM: Image restored successfully. [ 25.732283] PM: Basic memory bitmaps freed [ 25.732284] Restarting tasks ... [ 25.732476] [drm:intel_power_well_disable] disabling power well 2 [ 25.732481] [drm:skl_set_power_well] Disabling power well 2 [ 25.732482] [drm:intel_power_well_disable] disabling DC off [ 25.732483] [drm:gen9_enable_dc5] Enabling DC5 [ 25.732484] [drm:gen9_set_dc_state] Setting DC state from 00 to 01 [ 25.732641] done. [ 26.208288] asix 1-2.4:1.0 eth0: register 'asix' at usb-0000:00:15.0-2.4, ASIX AX88772 USB 2.0 Ethernet, 00:10:60:31:c2:a7 [ 26.208941] asix 1-2.4:1.0 enx00106031c2a7: renamed from eth0 [ 26.213162] Bluetooth: hci0: read Intel version: 370810011003110e23 [ 26.213163] Bluetooth: hci0: Intel device is already patched. patch num: 23 [ 26.226745] asix 1-2.4:1.0 enx00106031c2a7: link down [ 26.226919] IPv6: ADDRCONF(NETDEV_UP): enx00106031c2a7: link is not ready [ 26.649650] IPv6: ADDRCONF(NETDEV_CHANGE): enx00106031c2a7: link becomes ready [ 26.650228] asix 1-2.4:1.0 enx00106031c2a7: link up, 100Mbps, full-duplex, lpa 0xC5E1 [ 27.755238] [drm] GPU HANG: ecode 9:1:0xb89cb918, in gem_exec_suspen [1112], reason: Hang on blitter ring, action: reset [ 27.755239] [drm] GPU hangs can indicate a bug anywhere in the entire gfx stack, including userspace. [ 27.755240] [drm] Please file a _new_ bug report on bugs.freedesktop.org against DRI -> DRM/Intel [ 27.755240] [drm] drm/i915 developers can then reassign to the right component if it's not a kernel issue. [ 27.755240] [drm] The gpu crash dump is required to analyze gpu hangs, so please always attach it. [ 27.755241] [drm] GPU crash dump saved to /sys/class/drm/card0/error [ 27.755280] [drm:i915_reset_and_wakeup] resetting chip [ 27.755284] drm/i915: Resetting chip after gpu hang [ 27.755319] [drm:gen8_init_common_ring] Execlists enabled for render ring [ 27.755336] [drm:gen8_init_common_ring] Execlists enabled for blitter ring [ 27.755351] [drm:gen8_init_common_ring] Execlists enabled for bsd ring [ 27.755365] [drm:gen8_init_common_ring] Execlists enabled for video enhancement ring [ 27.755382] [drm:intel_guc_setup] GuC fw status: path i915/bxt_guc_ver8_7.bin, fetch SUCCESS, load SUCCESS [ 27.755383] [drm:intel_guc_setup] GuC fw status: fetch SUCCESS, load PENDING [ 27.756383] [drm:guc_ucode_xfer_dma] DMA status 0x10, GuC status 0x8002f0ec [ 27.756384] [drm:guc_ucode_xfer_dma] returning 0 [ 27.756385] [drm:intel_guc_setup] GuC fw status: fetch SUCCESS, load SUCCESS [ 27.756394] [drm:select_doorbell_register] assigned normal priority doorbell id 0x0 [ 27.756395] [drm:select_doorbell_cacheline] selected doorbell cacheline 0x80, next 0xc0, linesize 64 [ 27.756407] [drm:guc_client_alloc] new priority 2 client ffff88046ae71a00: ctx_index 0 [ 27.756407] [drm:guc_client_alloc] doorbell id 0, cacheline offset 0x80 [ 27.759754] gem_exec_suspend: exiting, ret=99 [ 27.759798] [drm:i915_gem_object_create_stolen] creating stolen object: size=4000 [ 27.759800] [drm:i915_pages_create_for_stolen] offset=0x7fa000, size=16384 [ 27.759822] [drm:i915_gem_object_create_stolen] creating stolen object: size=4000 [ 27.759823] [drm:i915_pages_create_for_stolen] offset=0x7fe000, size=16384 [ 27.759829] [drm:i915_gem_object_create_stolen] creating stolen object: size=4000 [ 27.759829] [drm:i915_pages_create_for_stolen] offset=0x802000, size=16384 [ 27.759852] [drm:i915_gem_object_create_stolen] creating stolen object: size=4000 [ 27.759853] [drm:i915_pages_create_for_stolen] offset=0x806000, size=16384 [ 28.314249] [drm] RC6 on [ 29.181467] [drm:i915_reset_and_wakeup] resetting chip [ 29.181472] drm/i915: Resetting chip after gpu hang [ 29.181518] [drm:gen8_init_common_ring] Execlists enabled for render ring [ 29.181535] [drm:gen8_init_common_ring] Execlists enabled for blitter ring [ 29.181549] [drm:gen8_init_common_ring] Execlists enabled for bsd ring [ 29.181564] [drm:gen8_init_common_ring] Execlists enabled for video enhancement ring [ 29.181585] [drm:intel_guc_setup] GuC fw status: path i915/bxt_guc_ver8_7.bin, fetch SUCCESS, load SUCCESS [ 29.181587] [drm:intel_guc_setup] GuC fw status: fetch SUCCESS, load PENDING [ 29.183539] [drm:guc_ucode_xfer_dma] DMA status 0x10, GuC status 0x8002f0ec [ 29.183541] [drm:guc_ucode_xfer_dma] returning 0 [ 29.183542] [drm:intel_guc_setup] GuC fw status: fetch SUCCESS, load SUCCESS [ 29.183551] [drm:select_doorbell_register] assigned normal priority doorbell id 0x0 [ 29.183552] [drm:select_doorbell_cacheline] selected doorbell cacheline 0xc0, next 0x100, linesize 64 [ 29.183558] [drm:guc_client_alloc] new priority 2 client ffff880469044880: ctx_index 0 [ 29.183559] [drm:guc_client_alloc] doorbell id 0, cacheline offset 0xc0 [ 29.185172] [drm:skl_update_scaler_plane] Updating scaler for [PLANE:23:plane 1A] scaler_user index 0.0 [ 29.784257] [drm] RC6 on [ 84.170886] gem_exec_suspend: executing [ 84.170927] [drm:i915_gem_open] [ 84.171003] [drm:i915_gem_object_create_stolen] creating stolen object: size=4000 [ 84.171004] [drm:i915_pages_create_for_stolen] offset=0x7fa000, size=16384 [ 84.171089] [drm:i915_gem_object_create_stolen] creating stolen object: size=4000 [ 84.171090] [drm:i915_pages_create_for_stolen] offset=0x7fe000, size=16384 [ 84.171102] [drm:i915_gem_object_create_stolen] creating stolen object: size=4000 [ 84.171103] [drm:i915_pages_create_for_stolen] offset=0x802000, size=16384 [ 84.171118] [drm:i915_gem_object_create_stolen] creating stolen object: size=4000 [ 84.171119] [drm:i915_pages_create_for_stolen] offset=0x806000, size=16384 [ 84.171368] [drm:i915_gem_open] [ 84.171672] [drm:i915_gem_object_create_stolen] creating stolen object: size=4000 [ 84.171674] [drm:i915_pages_create_for_stolen] offset=0x80a000, size=16384 [ 84.171717] [drm:i915_gem_object_create_stolen] creating stolen object: size=4000 [ 84.171718] [drm:i915_pages_create_for_stolen] offset=0x80e000, size=16384 [ 84.171735] [drm:i915_gem_object_create_stolen] creating stolen object: size=4000 [ 84.171736] [drm:i915_pages_create_for_stolen] offset=0x812000, size=16384 [ 84.171749] [drm:i915_gem_object_create_stolen] creating stolen object: size=4000 [ 84.171750] [drm:i915_pages_create_for_stolen] offset=0x816000, size=16384 [ 84.171965] [drm:skl_update_scaler_plane] Updating scaler for [PLANE:23:plane 1A] scaler_user index 0.0 [ 85.186614] gem_exec_suspend: executing [ 85.186653] [drm:i915_gem_open] [ 85.186719] [drm:i915_gem_object_create_stolen] creating stolen object: size=4000 [ 85.186721] [drm:i915_pages_create_for_stolen] offset=0x7fa000, size=16384 [ 85.186809] [drm:i915_gem_object_create_stolen] creating stolen object: size=4000 [ 85.186810] [drm:i915_pages_create_for_stolen] offset=0x7fe000, size=16384 [ 85.186832] [drm:i915_gem_object_create_stolen] creating stolen object: size=4000 [ 85.186833] [drm:i915_pages_create_for_stolen] offset=0x802000, size=16384 [ 85.186852] [drm:i915_gem_object_create_stolen] creating stolen object: size=4000 [ 85.186853] [drm:i915_pages_create_for_stolen] offset=0x806000, size=16384 [ 85.187266] [drm:i915_gem_open] [ 85.187400] gem_exec_suspend: starting subtest basic-S4 [ 85.257475] PM: Syncing filesystems ... done. [ 85.261723] Freezing user space processes ... (elapsed 0.012 seconds) done. [ 85.264759] Double checking all user space processes after OOM killer disable... (elapsed 0.002 seconds) [ 85.287254] PM: Marking nosave pages: [mem 0x00000000-0x00000fff] [ 85.287306] PM: Marking nosave pages: [mem 0x00058000-0x00058fff] [ 85.287307] PM: Marking nosave pages: [mem 0x0009e000-0x000fffff] [ 85.287332] PM: Marking nosave pages: [mem 0x0f000000-0x12151fff] [ 85.288286] PM: Marking nosave pages: [mem 0x77fde000-0x79e2dfff] [ 85.288935] PM: Marking nosave pages: [mem 0x7ac27000-0x7ac51fff] [ 85.288936] PM: Marking nosave pages: [mem 0x7b000000-0xffffffff] [ 85.297759] PM: Basic memory bitmaps created [ 85.298080] PM: Preallocating image memory... [ 85.552744] hpet1: lost 7161 rtc interrupts [ 85.784023] hpet1: lost 7161 rtc interrupts [ 86.015408] hpet1: lost 7161 rtc interrupts [ 86.226754] hpet1: lost 7161 rtc interrupts [ 86.438090] hpet1: lost 7161 rtc interrupts [ 86.459509] done (allocated 159038 pages) [ 86.459510] PM: Allocated 636152 kbytes in 4.85 seconds (131.16 MB/s) [ 86.459511] Freezing remaining freezable tasks ... (elapsed 0.003 seconds) done. [ 86.676757] hpet1: lost 7161 rtc interrupts [ 86.920438] hpet1: lost 7160 rtc interrupts [ 87.167089] hpet1: lost 7161 rtc interrupts [ 87.408866] hpet1: lost 7161 rtc interrupts [ 87.647930] Suspending console(s) (use no_console_suspend to debug) [ 87.655369] hpet1: lost 7161 rtc interrupts [ 87.681156] [drm:intel_power_well_enable] enabling DC off [ 87.681157] [drm:gen9_set_dc_state] Setting DC state from 01 to 00 [ 87.681163] [drm:intel_power_well_enable] enabling power well 2 [ 87.681164] [drm:skl_set_power_well] Enabling power well 2 [ 87.708180] igb 0000:01:00.0: System wakeup enabled by ACPI [ 87.756355] [drm:intel_power_well_enable] enabling dpio-common-bc [ 87.769650] [drm:connected_sink_compute_bpp] [CONNECTOR:39:eDP-1] checking for sink bpp constrains [ 87.769651] [drm:connected_sink_compute_bpp] clamping display bpp (was 36) to EDID reported max of 24 [ 87.769652] [drm:skl_update_scaler_crtc] Updating scaler for [CRTC:26:pipe A] scaler_user index 0.31 [ 87.769653] [drm:intel_dp_compute_config] DP link computation with max lane count 2 max bw 270000 pixel clock 138120KHz [ 87.769655] [drm:intel_dp_compute_config] DP link bw 0a rate select 00 lane count 2 clock 270000 bpp 24 [ 87.769656] [drm:intel_dp_compute_config] DP link bw required 331488 available 432000 [ 87.769657] [drm:intel_modeset_pipe_config] hw max bpp: 36, pipe bpp: 24, dithering: 0 [ 87.769658] [drm:intel_dump_pipe_config] [CRTC:26:pipe A][modeset] config ffff8804692d1800 for pipe A [ 87.769658] [drm:intel_dump_pipe_config] cpu_transcoder: EDP [ 87.769659] [drm:intel_dump_pipe_config] pipe bpp: 24, dithering: 0 [ 87.769659] [drm:intel_dump_pipe_config] fdi/pch: 0, lanes: 0, gmch_m: 0, gmch_n: 0, link_m: 0, link_n: 0, tu: 0 [ 87.769660] [drm:intel_dump_pipe_config] dp: 1, lanes: 2, gmch_m: 6436858, gmch_n: 8388608, link_m: 268202, link_n: 524288, tu: 64 [ 87.769661] [drm:intel_dump_pipe_config] dp: 1, lanes: 2, gmch_m2: 0, gmch_n2: 0, link_m2: 0, link_n2: 0, tu2: 0 [ 87.769661] [drm:intel_dump_pipe_config] audio: 0, infoframes: 0 [ 87.769661] [drm:intel_dump_pipe_config] requested mode: [ 87.769663] [drm:drm_mode_debug_printmodeline] Modeline 0:"1920x1080" 60 138120 1920 1968 2018 2052 1080 1084 1086 1122 0x48 0xa [ 87.769663] [drm:intel_dump_pipe_config] adjusted mode: [ 87.769664] [drm:drm_mode_debug_printmodeline] Modeline 0:"1920x1080" 60 138120 1920 1968 2018 2052 1080 1084 1086 1122 0x48 0xa [ 87.769665] [drm:intel_dump_crtc_timings] crtc timings: 138120 1920 1968 2018 2052 1080 1084 1086 1122, type: 0x48 flags: 0xa [ 87.769665] [drm:intel_dump_pipe_config] port clock: 270000 [ 87.769666] [drm:intel_dump_pipe_config] pipe src size: 1920x1080 [ 87.769666] [drm:intel_dump_pipe_config] num_scalers: 2, scaler_users: 0x0, scaler_id: -1 [ 87.769667] [drm:intel_dump_pipe_config] gmch pfit: control: 0x00000000, ratios: 0x00000000, lvds border: 0x00000000 [ 87.769667] [drm:intel_dump_pipe_config] pch pfit: pos: 0x00000000, size: 0x00000000, disabled [ 87.769668] [drm:intel_dump_pipe_config] ips: 0 [ 87.769668] [drm:intel_dump_pipe_config] double wide: 0 [ 87.769669] [drm:intel_dump_pipe_config] ddi_pll_sel: 0; dpll_hw_state: ebb0: 0x8100, ebb4: 0x2000,pll0: 0x1b, pll1: 0x100, pll2: 0x0, pll3: 0x0, pll6: 0x10803, pll8: 0x9, pll9: 0xa, pll10: 0x8003c00, pcsdw12: 0x4d [ 87.769670] [drm:intel_dump_pipe_config] planes on this crtc [ 87.769671] [drm:intel_dump_pipe_config] [PLANE:23:plane 1A] enabled [ 87.769672] [drm:intel_dump_pipe_config] FB:60, fb = 1920x1080 format = XR24 little-endian (0x34325258) [ 87.769672] [drm:intel_dump_pipe_config] scaler:-1 src 0x0+1920+1080 dst 0x0+1920+1080 [ 87.769673] [drm:intel_dump_pipe_config] [PLANE:25:cursor A] disabled, scaler_id = -1 [ 87.769673] [drm:intel_dump_pipe_config] [PLANE:27:plane 2A] disabled, scaler_id = -1 [ 87.769674] [drm:intel_dump_pipe_config] [PLANE:28:plane 3A] disabled, scaler_id = -1 [ 87.769675] [drm:intel_modeset_checks] New cdclk calculated to be atomic 144000, actual 144000 [ 87.769677] [drm:skl_update_scaler_plane] Updating scaler for [PLANE:23:plane 1A] scaler_user index 0.0 [ 87.769678] [drm:bxt_get_dpll] [CRTC:26:pipe A] using pre-allocated PORT PLL A [ 87.769678] [drm:intel_reference_shared_dpll] using PORT PLL A for pipe A [ 87.769679] [drm:skl_update_scaler_crtc] Updating scaler for [CRTC:26:pipe A] scaler_user index 0.31 [ 87.769688] [drm:intel_edp_backlight_off] [ 87.894140] hpet1: lost 7160 rtc interrupts [ 87.966249] [drm:intel_panel_actually_set_backlight] set backlight PWM = 0 [ 87.966253] [drm:intel_disable_pipe] disabling pipe A [ 87.968255] [drm:edp_panel_vdd_on] Turning eDP port A VDD on [ 87.968257] [drm:edp_panel_vdd_on] PP_STATUS: 0x80000008 PP_CONTROL: 0x0000006b [ 87.968508] [drm:edp_panel_off] Turn eDP port A panel power off [ 87.968560] [drm:wait_panel_off] Wait for panel power off time [ 87.968562] [drm:wait_panel_status] mask b0000000 value 00000000 status a0000002 control 00000060 [ 87.980661] [drm:wait_panel_status] Wait complete [ 87.980715] [drm:intel_disable_shared_dpll] disable PORT PLL A (active 1, on? 1) for crtc 26 [ 87.980901] [drm:intel_disable_shared_dpll] disabling PORT PLL A [ 87.981007] [drm:verify_encoder_state] [ENCODER:38:DDI A] [ 87.981034] [drm:verify_encoder_state] [ENCODER:46:DDI B] [ 87.981086] [drm:verify_encoder_state] [ENCODER:48:DP-MST A] [ 87.981087] [drm:verify_encoder_state] [ENCODER:49:DP-MST B] [ 87.981087] [drm:verify_encoder_state] [ENCODER:50:DP-MST C] [ 87.981087] [drm:verify_encoder_state] [ENCODER:53:DDI C] [ 87.981114] [drm:verify_encoder_state] [ENCODER:55:DP-MST A] [ 87.981114] [drm:verify_encoder_state] [ENCODER:56:DP-MST B] [ 87.981140] [drm:verify_encoder_state] [ENCODER:57:DP-MST C] [ 87.981167] [drm:intel_connector_verify_state] [CONNECTOR:47:DP-1] [ 87.981194] [drm:intel_get_hpd_pins] hotplug event received, stat 0x00000008, dig 0x1a001818, pins 0x00000010 [ 87.981195] [drm:intel_hpd_irq_handler] digital hpd port A - long [ 87.981195] [drm:intel_hpd_irq_storm_detect] Received HPD interrupt on PIN 4 - cnt: 0 [ 87.981203] [drm:intel_dp_hpd_pulse] ignoring long hpd on eDP port A [ 87.981224] [drm:intel_connector_verify_state] [CONNECTOR:51:HDMI-A-1] [ 87.981225] [drm:intel_connector_verify_state] [CONNECTOR:54:DP-2] [ 87.981252] [drm:intel_connector_verify_state] [CONNECTOR:58:HDMI-A-2] [ 87.981278] [drm:verify_single_dpll_state] PORT PLL A [ 87.981304] [drm:verify_single_dpll_state] PORT PLL B [ 87.981305] [drm:verify_single_dpll_state] PORT PLL C [ 87.981385] [drm:intel_connector_verify_state] [CONNECTOR:39:eDP-1] [ 87.981412] [drm:verify_crtc_state] [CRTC:26:pipe A] [ 87.981524] [drm:verify_single_dpll_state] PORT PLL A [ 87.982181] [drm:intel_power_well_disable] disabling dpio-common-bc [ 87.982207] [drm:intel_power_well_disable] disabling dpio-common-a [ 87.982233] [drm:intel_power_well_disable] disabling power well 2 [ 87.982288] [drm:skl_set_power_well] Disabling power well 2 [ 87.982314] [drm:intel_power_well_disable] disabling DC off [ 87.982341] [drm:gen9_enable_dc5] Enabling DC5 [ 87.982342] [drm:gen9_set_dc_state] Setting DC state from 00 to 01 [ 87.982368] [drm:intel_power_well_disable] disabling always-on [ 87.982443] PM: freeze of devices complete after 1398.167 msecs [ 87.982751] [drm:gen9_set_dc_state] Setting DC state from 01 to 00 [ 87.982764] [drm:bxt_set_cdclk] Changing CDCLK to 19200 kHz (VCO 0 kHz) [ 88.129315] [drm:intel_update_cdclk] Current CD clock rate: 19200 kHz, VCO: 0 kHz, ref: 19200 kHz [ 88.129316] [drm:intel_power_well_disable] disabling power well 1 [ 88.129318] [drm:skl_set_power_well] Disabling power well 1 [ 88.129319] [drm:gen9_sanitize_power_well_requests] Clearing auxiliary requests for power well 1 forced on by DMC [ 88.129321] [drm:bxt_enable_dc9] Enabling DC9 [ 88.129322] [drm:gen9_set_dc_state] Setting DC state from 00 to 08 [ 88.130483] hpet1: lost 7161 rtc interrupts [ 88.157634] PM: late freeze of devices complete after 732.249 msecs [ 88.168322] PM: noirq freeze of devices complete after 44.660 msecs [ 88.168390] ACPI: Preparing to enter system sleep state S4 [ 88.168585] ACPI : EC: EC stopped [ 88.168585] PM: Saving platform NVS memory [ 88.168773] Disabling non-boot CPUs ... [ 88.168992] Broke affinity for irq 128 [ 88.168993] Broke affinity for irq 130 [ 88.170003] smpboot: CPU 1 is now offline [ 88.173921] Broke affinity for irq 128 [ 88.173922] Broke affinity for irq 130 [ 88.174942] smpboot: CPU 2 is now offline [ 88.187000] Broke affinity for irq 1 [ 88.187004] Broke affinity for irq 8 [ 88.187006] Broke affinity for irq 9 [ 88.187036] Broke affinity for irq 39 [ 88.187041] Broke affinity for irq 122 [ 88.187042] Broke affinity for irq 128 [ 88.187043] Broke affinity for irq 129 [ 88.187043] Broke affinity for irq 130 [ 88.188052] smpboot: CPU 3 is now offline [ 88.195771] PM: Creating hibernation image: [ 88.391641] PM: Need to copy 156459 pages [ 88.391642] PM: Normal pages needed: 156459 + 1024, available pages: 3996536 [ 88.195941] PM: Restoring platform NVS memory [ 88.195977] ACPI : EC: EC started [ 88.196325] Enabling non-boot CPUs ... [ 88.204536] x86: Booting SMP configuration: [ 88.204537] smpboot: Booting Node 0 Processor 1 APIC 0x2 [ 88.206747] cache: parent cpu1 should not be sleeping [ 88.206887] CPU1 is up [ 88.216622] smpboot: Booting Node 0 Processor 2 APIC 0x4 [ 88.218838] cache: parent cpu2 should not be sleeping [ 88.218998] CPU2 is up [ 88.226446] smpboot: Booting Node 0 Processor 3 APIC 0x6 [ 88.228660] cache: parent cpu3 should not be sleeping [ 88.228839] CPU3 is up [ 88.229477] ACPI: Waking up from system sleep state S4 [ 88.240867] acpi LNXPOWER:04: Turning ON [ 88.271761] PM: noirq restore of devices complete after 56.969 msecs [ 88.271820] [drm:gen9_sanitize_dc_state] Resetting DC state tracking from 08 to 08 [ 88.271821] [drm:bxt_disable_dc9] Disabling DC9 [ 88.271822] [drm:gen9_set_dc_state] Setting DC state from 08 to 00 [ 88.271826] [drm:bxt_check_bios_rc6_setup] BIOS enabled RC states: HW_CTRL on HW_RC6 on SW_TARGET_STATE 0 [ 88.271872] [drm:gen9_set_dc_state] Setting DC state from 00 to 00 [ 88.271875] [drm:intel_power_well_enable] enabling power well 1 [ 88.271877] [drm:skl_set_power_well] Enabling power well 1 [ 88.273817] [drm:intel_update_cdclk] Current CD clock rate: 19200 kHz, VCO: 0 kHz, ref: 19200 kHz [ 88.273817] [drm:bxt_sanitize_cdclk] Sanitizing cdclk programmed by pre-os [ 88.273818] [drm:bxt_set_cdclk] Changing CDCLK to 144000 kHz (VCO 1152000 kHz) [ 88.277853] [drm:intel_update_cdclk] Current CD clock rate: 144000 kHz, VCO: 1152000 kHz, ref: 19200 kHz [ 88.277947] [drm:intel_power_well_enable] enabling always-on [ 88.277947] [drm:intel_power_well_enable] enabling DC off [ 88.277948] [drm:gen9_set_dc_state] Setting DC state from 00 to 00 [ 88.277950] [drm:intel_power_well_enable] enabling power well 2 [ 88.277950] [drm:skl_set_power_well] Enabling power well 2 [ 88.279961] [drm:intel_power_well_enable] enabling dpio-common-a [ 88.281999] [drm:intel_power_well_enable] enabling dpio-common-bc [ 88.282030] [drm:gen9_set_dc_state] Setting DC state from 00 to 00 [ 88.282046] [drm:bxt_ddi_phy_init] DDI PHY 1 already enabled, won't reprogram it [ 88.282055] [drm:bxt_ddi_phy_init] DDI PHY 0 already enabled, won't reprogram it [ 88.282093] PM: early restore of devices complete after 43.093 msecs [ 88.327355] usb usb1: root hub lost power or was reset [ 88.327356] usb usb2: root hub lost power or was reset [ 88.327398] [drm:intel_opregion_setup] graphic opregion physical addr: 0x79dd7018 [ 88.327429] [drm:intel_opregion_setup] Public ACPI methods supported [ 88.327430] [drm:intel_opregion_setup] ASLE supported [ 88.327432] [drm:intel_opregion_setup] Found valid VBT in ACPI OpRegion (RVDA) [ 88.327436] [drm:intel_dp_init_panel_power_sequencer_registers] panel power sequencer register settings: PP_ON 0x7d00001, PP_OFF 0x1f40001, PP_DIV 0x60 [ 88.327451] [drm:gen8_init_common_ring] Execlists enabled for render ring [ 88.327476] [drm:gen8_init_common_ring] Execlists enabled for blitter ring [ 88.327497] [drm:gen8_init_common_ring] Execlists enabled for bsd ring [ 88.327517] [drm:gen8_init_common_ring] Execlists enabled for video enhancement ring [ 88.327537] [drm:intel_guc_setup] GuC fw status: path i915/bxt_guc_ver8_7.bin, fetch SUCCESS, load SUCCESS [ 88.327540] [drm:intel_guc_setup] GuC fw status: fetch SUCCESS, load PENDING [ 88.327658] igb 0000:01:00.0: System wakeup disabled by ACPI [ 88.327709] rtc_cmos 00:04: System wakeup disabled by ACPI [ 88.329706] iwlwifi 0000:02:00.0: L1 Enabled - LTR Enabled [ 88.329887] iwlwifi 0000:02:00.0: L1 Enabled - LTR Enabled [ 88.331331] [drm:guc_ucode_xfer_dma] DMA status 0x10, GuC status 0x8002f0ec [ 88.331332] [drm:guc_ucode_xfer_dma] returning 0 [ 88.331333] [drm:intel_guc_setup] GuC fw status: fetch SUCCESS, load SUCCESS [ 88.331349] [drm:select_doorbell_register] assigned normal priority doorbell id 0x0 [ 88.331349] [drm:select_doorbell_cacheline] selected doorbell cacheline 0x100, next 0x140, linesize 64 [ 88.332061] sd 0:0:0:0: [sda] Starting disk [ 88.333377] [drm:guc_client_alloc] new priority 2 client ffff8804661a7400: ctx_index 0 [ 88.333378] [drm:guc_client_alloc] doorbell id 0, cacheline offset 0x100 [ 88.339168] [drm:intel_update_cdclk] Current CD clock rate: 144000 kHz, VCO: 1152000 kHz, ref: 19200 kHz [ 88.339173] [drm:bxt_hpd_irq_setup] Invert bit setting: hp_ctl:1a001818 hp_port:38 [ 88.339178] [drm:intel_modeset_readout_hw_state] [CRTC:26:pipe A] hw state readout: disabled [ 88.339179] [drm:intel_modeset_readout_hw_state] [CRTC:31:pipe B] hw state readout: disabled [ 88.339180] [drm:intel_modeset_readout_hw_state] [CRTC:36:pipe C] hw state readout: disabled [ 88.339181] [drm:intel_modeset_readout_hw_state] PORT PLL A hw state readout: crtc_mask 0x00000000, on 0 [ 88.339182] [drm:intel_modeset_readout_hw_state] PORT PLL B hw state readout: crtc_mask 0x00000000, on 0 [ 88.339183] [drm:intel_modeset_readout_hw_state] PORT PLL C hw state readout: crtc_mask 0x00000000, on 0 [ 88.339184] [drm:intel_modeset_readout_hw_state] [ENCODER:38:DDI A] hw state readout: disabled, pipe A [ 88.339185] [drm:intel_modeset_readout_hw_state] [ENCODER:46:DDI B] hw state readout: disabled, pipe A [ 88.339186] [drm:intel_modeset_readout_hw_state] [ENCODER:48:DP-MST A] hw state readout: disabled, pipe A [ 88.339186] [drm:intel_modeset_readout_hw_state] [ENCODER:49:DP-MST B] hw state readout: disabled, pipe B [ 88.339187] [drm:intel_modeset_readout_hw_state] [ENCODER:50:DP-MST C] hw state readout: disabled, pipe C [ 88.339188] [drm:intel_modeset_readout_hw_state] [ENCODER:53:DDI C] hw state readout: disabled, pipe A [ 88.339188] [drm:intel_modeset_readout_hw_state] [ENCODER:55:DP-MST A] hw state readout: disabled, pipe A [ 88.339189] [drm:intel_modeset_readout_hw_state] [ENCODER:56:DP-MST B] hw state readout: disabled, pipe B [ 88.339189] [drm:intel_modeset_readout_hw_state] [ENCODER:57:DP-MST C] hw state readout: disabled, pipe C [ 88.339190] [drm:intel_modeset_readout_hw_state] [CONNECTOR:39:eDP-1] hw state readout: disabled [ 88.339191] [drm:intel_modeset_readout_hw_state] [CONNECTOR:47:DP-1] hw state readout: disabled [ 88.339192] [drm:intel_modeset_readout_hw_state] [CONNECTOR:51:HDMI-A-1] hw state readout: disabled [ 88.339193] [drm:intel_modeset_readout_hw_state] [CONNECTOR:54:DP-2] hw state readout: disabled [ 88.339194] [drm:intel_modeset_readout_hw_state] [CONNECTOR:58:HDMI-A-2] hw state readout: disabled [ 88.339195] [drm:intel_dump_pipe_config] [CRTC:26:pipe A][setup_hw_state] config ffff8804692d1800 for pipe A [ 88.339196] [drm:intel_dump_pipe_config] cpu_transcoder: A [ 88.339196] [drm:intel_dump_pipe_config] pipe bpp: 0, dithering: 0 [ 88.339197] [drm:intel_dump_pipe_config] fdi/pch: 0, lanes: 0, gmch_m: 0, gmch_n: 0, link_m: 0, link_n: 0, tu: 0 [ 88.339198] [drm:intel_dump_pipe_config] dp: 0, lanes: 0, gmch_m: 0, gmch_n: 0, link_m: 0, link_n: 0, tu: 0 [ 88.339198] [drm:intel_dump_pipe_config] dp: 0, lanes: 0, gmch_m2: 0, gmch_n2: 0, link_m2: 0, link_n2: 0, tu2: 0 [ 88.339199] [drm:intel_dump_pipe_config] audio: 0, infoframes: 0 [ 88.339199] [drm:intel_dump_pipe_config] requested mode: [ 88.339200] [drm:drm_mode_debug_printmodeline] Modeline 0:"" 0 0 0 0 0 0 0 0 0 0 0x0 0x0 [ 88.339201] [drm:intel_dump_pipe_config] adjusted mode: [ 88.339201] [drm:drm_mode_debug_printmodeline] Modeline 0:"" 0 0 0 0 0 0 0 0 0 0 0x0 0x0 [ 88.339202] [drm:intel_dump_crtc_timings] crtc timings: 0 0 0 0 0 0 0 0 0, type: 0x0 flags: 0x0 [ 88.339203] [drm:intel_dump_pipe_config] port clock: 0 [ 88.339203] [drm:intel_dump_pipe_config] pipe src size: 0x0 [ 88.339204] [drm:intel_dump_pipe_config] num_scalers: 2, scaler_users: 0x0, scaler_id: 0 [ 88.339204] [drm:intel_dump_pipe_config] gmch pfit: control: 0x00000000, ratios: 0x00000000, lvds border: 0x00000000 [ 88.339205] [drm:intel_dump_pipe_config] pch pfit: pos: 0x00000000, size: 0x00000000, disabled [ 88.339205] [drm:intel_dump_pipe_config] ips: 0 [ 88.339205] [drm:intel_dump_pipe_config] double wide: 0 [ 88.339206] [drm:intel_dump_pipe_config] ddi_pll_sel: 0; dpll_hw_state: ebb0: 0x0, ebb4: 0x0,pll0: 0x0, pll1: 0x0, pll2: 0x0, pll3: 0x0, pll6: 0x0, pll8: 0x0, pll9: 0x0, pll10: 0x0, pcsdw12: 0x0 [ 88.339207] [drm:intel_dump_pipe_config] planes on this crtc [ 88.339208] [drm:intel_dump_pipe_config] [PLANE:23:plane 1A] enabled [ 88.339209] [drm:intel_dump_pipe_config] FB:60, fb = 1920x1080 format = XR24 little-endian (0x34325258) [ 88.339209] [drm:intel_dump_pipe_config] scaler:-1 src 0x0+1920+1080 dst 0x0+1920+1080 [ 88.339210] [drm:intel_dump_pipe_config] [PLANE:25:cursor A] disabled, scaler_id = -1 [ 88.339210] [drm:intel_dump_pipe_config] [PLANE:27:plane 2A] disabled, scaler_id = -1 [ 88.339211] [drm:intel_dump_pipe_config] [PLANE:28:plane 3A] disabled, scaler_id = -1 [ 88.339212] [drm:intel_dump_pipe_config] [CRTC:31:pipe B][setup_hw_state] config ffff8804692d1000 for pipe B [ 88.339212] [drm:intel_dump_pipe_config] cpu_transcoder: B [ 88.339213] [drm:intel_dump_pipe_config] pipe bpp: 0, dithering: 0 [ 88.339213] [drm:intel_dump_pipe_config] fdi/pch: 0, lanes: 0, gmch_m: 0, gmch_n: 0, link_m: 0, link_n: 0, tu: 0 [ 88.339214] [drm:intel_dump_pipe_config] dp: 0, lanes: 0, gmch_m: 0, gmch_n: 0, link_m: 0, link_n: 0, tu: 0 [ 88.339215] [drm:intel_dump_pipe_config] dp: 0, lanes: 0, gmch_m2: 0, gmch_n2: 0, link_m2: 0, link_n2: 0, tu2: 0 [ 88.339215] [drm:intel_dump_pipe_config] audio: 0, infoframes: 0 [ 88.339215] [drm:intel_dump_pipe_config] requested mode: [ 88.339216] [drm:drm_mode_debug_printmodeline] Modeline 0:"" 0 0 0 0 0 0 0 0 0 0 0x0 0x0 [ 88.339217] [drm:intel_dump_pipe_config] adjusted mode: [ 88.339217] [drm:drm_mode_debug_printmodeline] Modeline 0:"" 0 0 0 0 0 0 0 0 0 0 0x0 0x0 [ 88.339218] [drm:intel_dump_crtc_timings] crtc timings: 0 0 0 0 0 0 0 0 0, type: 0x0 flags: 0x0 [ 88.339219] [drm:intel_dump_pipe_config] port clock: 0 [ 88.339219] [drm:intel_dump_pipe_config] pipe src size: 0x0 [ 88.339219] [drm:intel_dump_pipe_config] num_scalers: 2, scaler_users: 0x0, scaler_id: 0 [ 88.339220] [drm:intel_dump_pipe_config] gmch pfit: control: 0x00000000, ratios: 0x00000000, lvds border: 0x00000000 [ 88.339220] [drm:intel_dump_pipe_config] pch pfit: pos: 0x00000000, size: 0x00000000, disabled [ 88.339221] [drm:intel_dump_pipe_config] ips: 0 [ 88.339221] [drm:intel_dump_pipe_config] double wide: 0 [ 88.339222] [drm:intel_dump_pipe_config] ddi_pll_sel: 0; dpll_hw_state: ebb0: 0x0, ebb4: 0x0,pll0: 0x0, pll1: 0x0, pll2: 0x0, pll3: 0x0, pll6: 0x0, pll8: 0x0, pll9: 0x0, pll10: 0x0, pcsdw12: 0x0 [ 88.339222] [drm:intel_dump_pipe_config] planes on this crtc [ 88.339223] [drm:intel_dump_pipe_config] [PLANE:29:plane 1B] disabled, scaler_id = -1 [ 88.339223] [drm:intel_dump_pipe_config] [PLANE:30:cursor B] disabled, scaler_id = -1 [ 88.339224] [drm:intel_dump_pipe_config] [PLANE:32:plane 2B] disabled, scaler_id = -1 [ 88.339224] [drm:intel_dump_pipe_config] [PLANE:33:plane 3B] disabled, scaler_id = -1 [ 88.339225] [drm:intel_dump_pipe_config] [CRTC:36:pipe C][setup_hw_state] config ffff8804686a7000 for pipe C [ 88.339225] [drm:intel_dump_pipe_config] cpu_transcoder: C [ 88.339226] [drm:intel_dump_pipe_config] pipe bpp: 0, dithering: 0 [ 88.339227] [drm:intel_dump_pipe_config] fdi/pch: 0, lanes: 0, gmch_m: 0, gmch_n: 0, link_m: 0, link_n: 0, tu: 0 [ 88.339227] [drm:intel_dump_pipe_config] dp: 0, lanes: 0, gmch_m: 0, gmch_n: 0, link_m: 0, link_n: 0, tu: 0 [ 88.339228] [drm:intel_dump_pipe_config] dp: 0, lanes: 0, gmch_m2: 0, gmch_n2: 0, link_m2: 0, link_n2: 0, tu2: 0 [ 88.339228] [drm:intel_dump_pipe_config] audio: 0, infoframes: 0 [ 88.339229] [drm:intel_dump_pipe_config] requested mode: [ 88.339229] [drm:drm_mode_debug_printmodeline] Modeline 0:"" 0 0 0 0 0 0 0 0 0 0 0x0 0x0 [ 88.339230] [drm:intel_dump_pipe_config] adjusted mode: [ 88.339231] [drm:drm_mode_debug_printmodeline] Modeline 0:"" 0 0 0 0 0 0 0 0 0 0 0x0 0x0 [ 88.339231] [drm:intel_dump_crtc_timings] crtc timings: 0 0 0 0 0 0 0 0 0, type: 0x0 flags: 0x0 [ 88.339232] [drm:intel_dump_pipe_config] port clock: 0 [ 88.339232] [drm:intel_dump_pipe_config] pipe src size: 0x0 [ 88.339233] [drm:intel_dump_pipe_config] num_scalers: 1, scaler_users: 0x0, scaler_id: 0 [ 88.339233] [drm:intel_dump_pipe_config] gmch pfit: control: 0x00000000, ratios: 0x00000000, lvds border: 0x00000000 [ 88.339234] [drm:intel_dump_pipe_config] pch pfit: pos: 0x00000000, size: 0x00000000, disabled [ 88.339234] [drm:intel_dump_pipe_config] ips: 0 [ 88.339234] [drm:intel_dump_pipe_config] double wide: 0 [ 88.339235] [drm:intel_dump_pipe_config] ddi_pll_sel: 0; dpll_hw_state: ebb0: 0x0, ebb4: 0x0,pll0: 0x0, pll1: 0x0, pll2: 0x0, pll3: 0x0, pll6: 0x0, pll8: 0x0, pll9: 0x0, pll10: 0x0, pcsdw12: 0x0 [ 88.339235] [drm:intel_dump_pipe_config] planes on this crtc [ 88.339236] [drm:intel_dump_pipe_config] [PLANE:34:plane 1C] disabled, scaler_id = -1 [ 88.339236] [drm:intel_dump_pipe_config] [PLANE:35:cursor C] disabled, scaler_id = -1 [ 88.339237] [drm:intel_dump_pipe_config] [PLANE:37:plane 2C] disabled, scaler_id = -1 [ 88.339252] [drm:intel_power_well_disable] disabling dpio-common-bc [ 88.339253] [drm:intel_power_well_disable] disabling dpio-common-a [ 88.339258] [drm:connected_sink_compute_bpp] [CONNECTOR:39:eDP-1] checking for sink bpp constrains [ 88.339258] [drm:connected_sink_compute_bpp] clamping display bpp (was 36) to EDID reported max of 24 [ 88.339260] [drm:skl_update_scaler_crtc] Updating scaler for [CRTC:26:pipe A] scaler_user index 0.31 [ 88.339261] [drm:intel_dp_compute_config] DP link computation with max lane count 2 max bw 270000 pixel clock 138120KHz [ 88.339263] [drm:intel_dp_compute_config] DP link bw 0a rate select 00 lane count 2 clock 270000 bpp 24 [ 88.339263] [drm:intel_dp_compute_config] DP link bw required 331488 available 432000 [ 88.339264] [drm:intel_modeset_pipe_config] hw max bpp: 36, pipe bpp: 24, dithering: 0 [ 88.339265] [drm:intel_dump_pipe_config] [CRTC:26:pipe A][modeset] config ffff8804692d2800 for pipe A [ 88.339265] [drm:intel_dump_pipe_config] cpu_transcoder: EDP [ 88.339265] [drm:intel_dump_pipe_config] pipe bpp: 24, dithering: 0 [ 88.339266] [drm:intel_dump_pipe_config] fdi/pch: 0, lanes: 0, gmch_m: 0, gmch_n: 0, link_m: 0, link_n: 0, tu: 0 [ 88.339267] [drm:intel_dump_pipe_config] dp: 1, lanes: 2, gmch_m: 6436858, gmch_n: 8388608, link_m: 268202, link_n: 524288, tu: 64 [ 88.339268] [drm:intel_dump_pipe_config] dp: 1, lanes: 2, gmch_m2: 0, gmch_n2: 0, link_m2: 0, link_n2: 0, tu2: 0 [ 88.339268] [drm:intel_dump_pipe_config] audio: 0, infoframes: 0 [ 88.339268] [drm:intel_dump_pipe_config] requested mode: [ 88.339269] [drm:drm_mode_debug_printmodeline] Modeline 0:"1920x1080" 60 138120 1920 1968 2018 2052 1080 1084 1086 1122 0x48 0xa [ 88.339270] [drm:intel_dump_pipe_config] adjusted mode: [ 88.339271] [drm:drm_mode_debug_printmodeline] Modeline 0:"1920x1080" 60 138120 1920 1968 2018 2052 1080 1084 1086 1122 0x48 0xa [ 88.339272] [drm:intel_dump_crtc_timings] crtc timings: 138120 1920 1968 2018 2052 1080 1084 1086 1122, type: 0x48 flags: 0xa [ 88.339272] [drm:intel_dump_pipe_config] port clock: 270000 [ 88.339272] [drm:intel_dump_pipe_config] pipe src size: 1920x1080 [ 88.339273] [drm:intel_dump_pipe_config] num_scalers: 2, scaler_users: 0x0, scaler_id: -1 [ 88.339273] [drm:intel_dump_pipe_config] gmch pfit: control: 0x00000000, ratios: 0x00000000, lvds border: 0x00000000 [ 88.339274] [drm:intel_dump_pipe_config] pch pfit: pos: 0x00000000, size: 0x00000000, disabled [ 88.339274] [drm:intel_dump_pipe_config] ips: 0 [ 88.339275] [drm:intel_dump_pipe_config] double wide: 0 [ 88.339276] [drm:intel_dump_pipe_config] ddi_pll_sel: 0; dpll_hw_state: ebb0: 0x8100, ebb4: 0x2000,pll0: 0x1b, pll1: 0x100, pll2: 0x0, pll3: 0x0, pll6: 0x10803, pll8: 0x9, pll9: 0xa, pll10: 0x8003c00, pcsdw12: 0x4d [ 88.339276] [drm:intel_dump_pipe_config] planes on this crtc [ 88.339277] [drm:intel_dump_pipe_config] [PLANE:23:plane 1A] enabled [ 88.339278] [drm:intel_dump_pipe_config] FB:60, fb = 1920x1080 format = XR24 little-endian (0x34325258) [ 88.339278] [drm:intel_dump_pipe_config] scaler:-1 src 0x0+1920+1080 dst 0x0+1920+1080 [ 88.339279] [drm:intel_dump_pipe_config] [PLANE:25:cursor A] disabled, scaler_id = -1 [ 88.339279] [drm:intel_dump_pipe_config] [PLANE:27:plane 2A] disabled, scaler_id = -1 [ 88.339280] [drm:intel_dump_pipe_config] [PLANE:28:plane 3A] disabled, scaler_id = -1 [ 88.339281] [drm:intel_modeset_checks] New cdclk calculated to be atomic 144000, actual 144000 [ 88.339282] [drm:skl_update_scaler_plane] Updating scaler for [PLANE:23:plane 1A] scaler_user index 0.0 [ 88.339284] [drm:bxt_get_dpll] [CRTC:26:pipe A] using pre-allocated PORT PLL A [ 88.339284] [drm:intel_reference_shared_dpll] using PORT PLL A for pipe A [ 88.339285] [drm:skl_update_scaler_crtc] Updating scaler for [CRTC:26:pipe A] scaler_user index 0.31 [ 88.339286] [drm:skl_update_scaler_crtc] Updating scaler for [CRTC:31:pipe B] scaler_user index 1.31 [ 88.339286] [drm:skl_update_scaler_crtc] Updating scaler for [CRTC:36:pipe C] scaler_user index 2.31 [ 88.339294] [drm:intel_power_well_enable] enabling dpio-common-a [ 88.340377] [drm:verify_encoder_state] [ENCODER:38:DDI A] [ 88.340377] [drm:verify_encoder_state] [ENCODER:46:DDI B] [ 88.340378] [drm:verify_encoder_state] [ENCODER:48:DP-MST A] [ 88.340378] [drm:verify_encoder_state] [ENCODER:49:DP-MST B] [ 88.340379] [drm:verify_encoder_state] [ENCODER:50:DP-MST C] [ 88.340379] [drm:verify_encoder_state] [ENCODER:53:DDI C] [ 88.340380] [drm:verify_encoder_state] [ENCODER:55:DP-MST A] [ 88.340380] [drm:verify_encoder_state] [ENCODER:56:DP-MST B] [ 88.340380] [drm:verify_encoder_state] [ENCODER:57:DP-MST C] [ 88.340381] [drm:intel_connector_verify_state] [CONNECTOR:47:DP-1] [ 88.340381] [drm:intel_connector_verify_state] [CONNECTOR:51:HDMI-A-1] [ 88.340382] [drm:intel_connector_verify_state] [CONNECTOR:54:DP-2] [ 88.340382] [drm:intel_connector_verify_state] [CONNECTOR:58:HDMI-A-2] [ 88.340383] [drm:verify_single_dpll_state] PORT PLL A [ 88.340384] [drm:verify_single_dpll_state] PORT PLL B [ 88.340384] [drm:verify_single_dpll_state] PORT PLL C [ 88.340389] [drm:intel_enable_shared_dpll] enable PORT PLL A (active 1, on? 0) for crtc 26 [ 88.340389] [drm:intel_enable_shared_dpll] enabling PORT PLL A [ 88.340428] [drm:edp_panel_on] Turn eDP port A panel power on [ 88.340429] [drm:wait_panel_power_cycle] Wait for panel power cycle [ 88.340431] [drm:wait_panel_status] mask b800000f value 00000000 status 00000000 control 00000060 [ 88.340432] [drm:wait_panel_status] Wait complete [ 88.340433] [drm:wait_panel_on] Wait for panel power on [ 88.340434] [drm:wait_panel_status] mask b000000f value 80000008 status 0000000a control 00000063 [ 88.356527] iwlwifi 0000:02:00.0: L1 Enabled - LTR Enabled [ 88.356737] iwlwifi 0000:02:00.0: L1 Enabled - LTR Enabled [ 88.366177] [drm:intel_get_hpd_pins] hotplug event received, stat 0x00000008, dig 0x1a001818, pins 0x00000010 [ 88.366177] [drm:intel_hpd_irq_handler] digital hpd port A - long [ 88.366178] [drm:intel_hpd_irq_storm_detect] Received HPD interrupt on PIN 4 - cnt: 0 [ 88.366190] [drm:intel_dp_hpd_pulse] ignoring long hpd on eDP port A [ 88.386286] atkbd serio0: Failed to deactivate keyboard on isa0060/serio0 [ 88.388600] [drm:wait_panel_status] Wait complete [ 88.388602] [drm:edp_panel_vdd_on] Turning eDP port A VDD on [ 88.388603] [drm:edp_panel_vdd_on] PP_STATUS: 0x80000008 PP_CONTROL: 0x0000006b [ 88.389367] [drm:intel_dp_set_signal_levels] Using vswing level 0 [ 88.389368] [drm:intel_dp_set_signal_levels] Using pre-emphasis level 0 [ 88.389622] [drm:intel_dp_link_training_clock_recovery] clock recovery OK [ 88.390184] [drm:intel_dp_link_training_channel_equalization] Channel EQ done. DP Training successful [ 88.390244] [drm:skylake_pfit_enable] for crtc_state = ffff8804692d2800 [ 88.390303] [drm:skl_wm_flush_pipe] flush pipe A (pass 3) [ 88.390305] [drm:intel_enable_pipe] enabling pipe A [ 88.390310] [drm:intel_edp_backlight_on] [ 88.390311] [drm:intel_panel_enable_backlight] pipe A [ 88.390311] [drm:intel_panel_actually_set_backlight] set backlight PWM = 96000 [ 88.391750] [drm:intel_psr_enable] PSR not supported on this platform [ 88.391750] [drm:intel_edp_drrs_enable] Panel doesn't support DRRS [ 88.394485] [drm:intel_connector_verify_state] [CONNECTOR:39:eDP-1] [ 88.394538] [drm:verify_crtc_state] [CRTC:26:pipe A] [ 88.395052] [drm:verify_single_dpll_state] PORT PLL A [ 88.395285] [drm:verify_crtc_state] [CRTC:31:pipe B] [ 88.395312] [drm:verify_crtc_state] [CRTC:36:pipe C] [ 88.395475] [drm:bxt_hpd_irq_setup] Invert bit setting: hp_ctl:18001818 hp_port:38 [ 88.395501] [drm:intel_dp_detect] [CONNECTOR:39:eDP-1] [ 88.395974] [drm:intel_dp_probe_oui] Sink OUI: 001cf8 [ 88.396339] [drm:intel_dp_probe_oui] Branch OUI: 000000 [ 88.396654] [drm:drm_helper_hpd_irq_event] [CONNECTOR:39:eDP-1] status updated from connected to connected [ 88.396680] [drm:intel_dp_detect] [CONNECTOR:47:DP-1] [ 88.396681] [drm:intel_power_well_enable] enabling dpio-common-bc [ 88.396914] [drm:intel_power_well_disable] disabling dpio-common-bc [ 88.396947] [drm:drm_helper_hpd_irq_event] [CONNECTOR:47:DP-1] status updated from disconnected to disconnected [ 88.396947] [drm:intel_hdmi_detect] [CONNECTOR:51:HDMI-A-1] [ 88.441267] usb 1-2: reset high-speed USB device number 2 using xhci_hcd [ 88.453282] [drm:intel_hdmi_detect] HDMI live status down [ 88.453283] [drm:drm_helper_hpd_irq_event] [CONNECTOR:51:HDMI-A-1] status updated from disconnected to disconnected [ 88.453284] [drm:intel_dp_detect] [CONNECTOR:54:DP-2] [ 88.453284] [drm:intel_power_well_enable] enabling dpio-common-bc [ 88.453309] [drm:intel_power_well_disable] disabling dpio-common-bc [ 88.453311] [drm:drm_helper_hpd_irq_event] [CONNECTOR:54:DP-2] status updated from disconnected to disconnected [ 88.453311] [drm:intel_hdmi_detect] [CONNECTOR:58:HDMI-A-2] [ 88.453941] atkbd serio0: Failed to enable keyboard on isa0060/serio0 [ 88.511229] [drm:intel_hdmi_detect] HDMI live status down [ 88.511256] [drm:drm_helper_hpd_irq_event] [CONNECTOR:58:HDMI-A-2] status updated from disconnected to disconnected [ 88.516995] usb 1-7: reset full-speed USB device number 3 using xhci_hcd [ 88.517967] [drm:intel_didl_outputs] More than 15 outputs detected via ACPI [ 88.552275] hpet1: lost 7161 rtc interrupts [ 88.556676] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [ 88.556837] ata1.00: configured for UDMA/133 [ 88.589575] usb 1-2.2: reset high-speed USB device number 4 using xhci_hcd [ 88.634016] ata1.00: Enabling discard_zeroes_data [ 88.674720] usb 1-2.3: reset low-speed USB device number 5 using xhci_hcd [ 88.753041] [drm] RC6 on [ 88.791850] hpet1: lost 7161 rtc interrupts [ 88.996261] [drm:edp_panel_vdd_off_sync] Turning eDP port A VDD off [ 88.996313] [drm:edp_panel_vdd_off_sync] PP_STATUS: 0x80000008 PP_CONTROL: 0x00000067 [ 89.034262] hpet1: lost 7161 rtc interrupts [ 89.147654] usb 1-2.2.4: reset low-speed USB device number 7 using xhci_hcd [ 89.280709] hpet1: lost 7161 rtc interrupts [ 89.343820] PM: restore of devices complete after 4248.974 msecs [ 89.344974] usb 1-7:1.0: rebind failed: -517 [ 89.344976] usb 1-7:1.1: rebind failed: -517 [ 89.345068] PM: Image restored successfully. [ 89.345090] PM: Basic memory bitmaps freed [ 89.345091] Restarting tasks ... [ 89.349002] [drm:intel_power_well_disable] disabling power well 2 [ 89.349014] [drm:skl_set_power_well] Disabling power well 2 [ 89.349016] [drm:intel_power_well_disable] disabling DC off [ 89.349018] [drm:gen9_enable_dc5] Enabling DC5 [ 89.349019] [drm:gen9_set_dc_state] Setting DC state from 00 to 01 [ 89.349177] done. [ 89.349692] usb 1-2.4: USB disconnect, device number 9 [ 89.349724] asix 1-2.4:1.0 enx00106031c2a7: unregister 'asix' usb-0000:00:15.0-2.4, ASIX AX88772 USB 2.0 Ethernet [ 89.359031] Bluetooth: hci0: read Intel version: 370810011003110e23 [ 89.359083] Bluetooth: hci0: Intel device is already patched. patch num: 23 [ 89.382430] usb 1-2.4: new high-speed USB device number 10 using xhci_hcd [ 89.411419] usb 1-2.4: New USB device found, idVendor=0b95, idProduct=7720 [ 89.411420] usb 1-2.4: New USB device strings: Mfr=1, Product=2, SerialNumber=3 [ 89.411421] usb 1-2.4: Product: AX88772 [ 89.411421] usb 1-2.4: SerialNumber: 00D91E [ 90.004446] asix 1-2.4:1.0 eth0: register 'asix' at usb-0000:00:15.0-2.4, ASIX AX88772 USB 2.0 Ethernet, 00:10:60:31:c2:a7 [ 90.480076] asix 1-2.4:1.0 enx00106031c2a7: renamed from eth0 [ 90.860311] asix 1-2.4:1.0 enx00106031c2a7: link up, 100Mbps, full-duplex, lpa 0xC5E1 [ 90.901152] asix 1-2.4:1.0 enx00106031c2a7: link up, 100Mbps, full-duplex, lpa 0xC5E1 [ 91.362485] [drm:i915_reset_and_wakeup] resetting chip [ 91.362490] drm/i915: Resetting chip after gpu hang [ 91.362536] [drm:gen8_init_common_ring] Execlists enabled for render ring [ 91.362553] [drm:gen8_init_common_ring] Execlists enabled for blitter ring [ 91.362567] [drm:gen8_init_common_ring] Execlists enabled for bsd ring [ 91.362581] [drm:gen8_init_common_ring] Execlists enabled for video enhancement ring [ 91.362595] [drm:intel_guc_setup] GuC fw status: path i915/bxt_guc_ver8_7.bin, fetch SUCCESS, load SUCCESS [ 91.362597] [drm:intel_guc_setup] GuC fw status: fetch SUCCESS, load PENDING [ 91.363887] [drm:guc_ucode_xfer_dma] DMA status 0x10, GuC status 0x8002f0ec [ 91.363888] [drm:guc_ucode_xfer_dma] returning 0 [ 91.363889] [drm:intel_guc_setup] GuC fw status: fetch SUCCESS, load SUCCESS [ 91.363900] [drm:select_doorbell_register] assigned normal priority doorbell id 0x0 [ 91.363901] [drm:select_doorbell_cacheline] selected doorbell cacheline 0x140, next 0x180, linesize 64 [ 91.363907] [drm:guc_client_alloc] new priority 2 client ffff8804657db880: ctx_index 0 [ 91.363907] [drm:guc_client_alloc] doorbell id 0, cacheline offset 0x140 [ 91.365533] gem_exec_suspend: exiting, ret=99 [ 91.365559] [drm:i915_gem_object_create_stolen] creating stolen object: size=4000 [ 91.365560] [drm:i915_pages_create_for_stolen] offset=0x7fa000, size=16384 [ 91.365595] [drm:i915_gem_object_create_stolen] creating stolen object: size=4000 [ 91.365596] [drm:i915_pages_create_for_stolen] offset=0x7fe000, size=16384 [ 91.365620] [drm:i915_gem_object_create_stolen] creating stolen object: size=4000 [ 91.365621] [drm:i915_pages_create_for_stolen] offset=0x802000, size=16384 [ 91.365655] [drm:i915_gem_object_create_stolen] creating stolen object: size=4000 [ 91.365655] [drm:i915_pages_create_for_stolen] offset=0x806000, size=16384 [ 91.905719] [drm] RC6 on [ 92.932397] [drm:i915_reset_and_wakeup] resetting chip [ 92.932402] drm/i915: Resetting chip after gpu hang [ 92.932446] [drm:gen8_init_common_ring] Execlists enabled for render ring [ 92.932463] [drm:gen8_init_common_ring] Execlists enabled for blitter ring [ 92.932477] [drm:gen8_init_common_ring] Execlists enabled for bsd ring [ 92.932491] [drm:gen8_init_common_ring] Execlists enabled for video enhancement ring [ 92.932505] [drm:intel_guc_setup] GuC fw status: path i915/bxt_guc_ver8_7.bin, fetch SUCCESS, load SUCCESS [ 92.932507] [drm:intel_guc_setup] GuC fw status: fetch SUCCESS, load PENDING [ 92.934459] [drm:guc_ucode_xfer_dma] DMA status 0x10, GuC status 0x8002f0ec [ 92.934460] [drm:guc_ucode_xfer_dma] returning 0 [ 92.934461] [drm:intel_guc_setup] GuC fw status: fetch SUCCESS, load SUCCESS [ 92.934469] [drm:select_doorbell_register] assigned normal priority doorbell id 0x0 [ 92.934470] [drm:select_doorbell_cacheline] selected doorbell cacheline 0x180, next 0x1c0, linesize 64 [ 92.934476] [drm:guc_client_alloc] new priority 2 client ffff880469044780: ctx_index 0 [ 92.934476] [drm:guc_client_alloc] doorbell id 0, cacheline offset 0x180 [ 92.936117] [drm:skl_update_scaler_plane] Updating scaler for [PLANE:23:plane 1A] scaler_user index 0.0 [ 93.317037] [drm] RC6 on