Linux version 2.6.23 (root@x-q965) (gcc version 4.1.0 20060304 (Red Hat 4.1.0-3)) #2 SMP Thu Feb 21 16:37:22 CST 2008 BIOS-provided physical RAM map: BIOS-e820: 0000000000000000 - 000000000009fc00 (usable) BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved) BIOS-e820: 0000000000100000 - 000000003f5ffc00 (usable) BIOS-e820: 000000003f5ffc00 - 000000003f601c00 (ACPI NVS) BIOS-e820: 000000003f603c00 - 000000003f653c00 (reserved) BIOS-e820: 000000003f653c00 - 000000003f655c00 (ACPI data) BIOS-e820: 000000003f655c00 - 0000000040000000 (reserved) BIOS-e820: 00000000e0000000 - 00000000f0000000 (reserved) BIOS-e820: 00000000fec00000 - 00000000fed00400 (reserved) BIOS-e820: 00000000fed20000 - 00000000feda0000 (reserved) BIOS-e820: 00000000fee00000 - 00000000fef00000 (reserved) BIOS-e820: 00000000ffb00000 - 0000000100000000 (reserved) Warning only 896MB will be used. Use a HIGHMEM enabled kernel. 896MB LOWMEM available. found SMP MP-table at 000fe710 Entering add_active_range(0, 0, 229376) 0 entries of 256 used Zone PFN ranges: DMA 0 -> 4096 Normal 4096 -> 229376 Movable zone start PFN for each node early_node_map[1] active PFN ranges 0: 0 -> 229376 On node 0 totalpages: 229376 DMA zone: 32 pages used for memmap DMA zone: 0 pages reserved DMA zone: 4064 pages, LIFO batch:0 Normal zone: 1760 pages used for memmap Normal zone: 223520 pages, LIFO batch:31 Movable zone: 0 pages used for memmap DMI 2.3 present. ACPI: RSDP 000FEBF0, 0024 (r2 DELL ) ACPI: XSDT 000FCE8E, 006C (r1 DELL B8K 14 ASL 61) ACPI: FACP 000FCFB6, 00F4 (r3 DELL B8K 14 ASL 61) ACPI: DSDT FFF69AB8, 4337 (r1 DELL dt_ex 1000 INTL 20050624) ACPI: FACS 3F5FFC00, 0040 ACPI: SSDT FFF6DF0E, 00AA (r1 DELL st_ex 1000 INTL 20050624) ACPI: APIC 000FD0AA, 0092 (r1 DELL B8K 14 ASL 61) ACPI: BOOT 000FD13C, 0028 (r1 DELL B8K 14 ASL 61) ACPI: ASF! 000FD164, 0092 (r32 DELL B8K 14 ASL 61) ACPI: MCFG 000FD1F6, 003E (r1 DELL B8K 14 ASL 61) ACPI: HPET 000FD234, 0038 (r1 DELL B8K 14 ASL 61) ACPI: TCPA 000FD490, 0032 (r1 DELL B8K 14 ASL 61) ACPI: SLIC 000FD26C, 0176 (r1 DELL B8K 14 ASL 61) ACPI: PM-Timer IO Port: 0x808 ACPI: Local APIC address 0xfee00000 ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled) Processor #0 15:4 APIC version 20 ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] enabled) Processor #1 15:4 APIC version 20 ACPI: LAPIC (acpi_id[0x03] lapic_id[0x05] disabled) ACPI: LAPIC (acpi_id[0x04] lapic_id[0x07] disabled) ACPI: LAPIC (acpi_id[0x05] lapic_id[0x00] disabled) ACPI: LAPIC (acpi_id[0x06] lapic_id[0x01] disabled) ACPI: LAPIC (acpi_id[0x07] lapic_id[0x02] disabled) ACPI: LAPIC (acpi_id[0x08] lapic_id[0x03] disabled) ACPI: LAPIC_NMI (acpi_id[0xff] high level lint[0x1]) ACPI: IOAPIC (id[0x08] address[0xfec00000] gsi_base[0]) IOAPIC[0]: apic_id 8, version 32, address 0xfec00000, GSI 0-23 ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl) ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level) ACPI: IRQ0 used by override. ACPI: IRQ2 used by override. ACPI: IRQ9 used by override. Enabling APIC mode: Flat. Using 1 I/O APICs ACPI: HPET id: 0x8086a201 base: 0xfed00000 Using ACPI (MADT) for SMP configuration information Allocating PCI resources starting at 50000000 (gap: 40000000:a0000000) Built 1 zonelists in Zone order. Total pages: 227584 Kernel command line: ro root=LABEL=/ irqpoll Misrouted IRQ fixup and polling support enabled This may significantly impact system performance mapped APIC to ffffb000 (fee00000) mapped IOAPIC to ffffa000 (fec00000) Enabling fast FPU save and restore... done. Enabling unmasked SIMD FPU exception support... done. Initializing CPU#0 PID hash table entries: 4096 (order: 12, 16384 bytes) Detected 2791.221 MHz processor. Console: colour VGA+ 80x25 console [tty0] enabled Dentry cache hash table entries: 131072 (order: 7, 524288 bytes) Inode-cache hash table entries: 65536 (order: 6, 262144 bytes) Memory: 902660k/917504k available (2982k kernel code, 14356k reserved, 1499k data, 244k init, 0k highmem) virtual kernel memory layout: fixmap : 0xfffb5000 - 0xfffff000 ( 296 kB) vmalloc : 0xf8800000 - 0xfffb3000 ( 119 MB) lowmem : 0xc0000000 - 0xf8000000 ( 896 MB) .init : 0xc0569000 - 0xc05a6000 ( 244 kB) .data : 0xc03e9ae0 - 0xc0560acc (1499 kB) .text : 0xc0100000 - 0xc03e9ae0 (2982 kB) Checking if this processor honours the WP bit even in supervisor mode... Ok. hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0 hpet0: 3 64-bit timers, 14318180 Hz Calibrating delay using timer specific routine.. 5609.97 BogoMIPS (lpj=11219948) Mount-cache hash table entries: 512 CPU: After generic identify, caps: bfebfbff 20100000 00000000 00000000 0000641d 00000000 00000001 00000000 monitor/mwait feature present. using mwait in idle threads. CPU: Trace cache: 12K uops, L1 D cache: 16K CPU: L2 cache: 1024K CPU: Physical Processor ID: 0 CPU: Processor Core ID: 0 CPU: After all inits, caps: bfebfbff 20100000 00000000 0000b180 0000641d 00000000 00000001 00000000 Intel machine check architecture supported. Intel machine check reporting enabled on CPU#0. CPU0: Intel P4/Xeon Extended MCE MSRs (24) available Compat vDSO mapped to ffffe000. Checking 'hlt' instruction... OK. SMP alternatives: switching to UP code ACPI: Core revision 20070126 Parsing all Control Methods: Table [DSDT](id 0001) - 500 Objects with 45 Devices 190 Methods 39 Regions Parsing all Control Methods: Table [SSDT](id 0002) - 7 Objects with 0 Devices 2 Methods 0 Regions tbxface-0598 [00] tb_load_namespace : ACPI Tables successfully acquired evxfevnt-0091 [00] enable : Transition to ACPI mode successful CPU0: Intel(R) Pentium(R) D CPU 2.80GHz stepping 07 SMP alternatives: switching to SMP code Booting processor 1/1 eip 3000 Initializing CPU#1 Calibrating delay using timer specific routine.. 5582.05 BogoMIPS (lpj=11164110) CPU: After generic identify, caps: bfebfbff 20100000 00000000 00000000 0000641d 00000000 00000001 00000000 monitor/mwait feature present. CPU: Trace cache: 12K uops, L1 D cache: 16K CPU: L2 cache: 1024K CPU: Physical Processor ID: 0 CPU: Processor Core ID: 1 CPU: After all inits, caps: bfebfbff 20100000 00000000 0000b180 0000641d 00000000 00000001 00000000 Intel machine check architecture supported. Intel machine check reporting enabled on CPU#1. CPU1: Intel P4/Xeon Extended MCE MSRs (24) available CPU1: Intel(R) Pentium(R) D CPU 2.80GHz stepping 07 Total of 2 processors activated (11192.02 BogoMIPS). ENABLING IO-APIC IRQs ..TIMER: vector=0x31 apic1=0 pin1=2 apic2=-1 pin2=-1 checking TSC synchronization [CPU#0 -> CPU#1]: passed. Brought up 2 CPUs NET: Registered protocol family 16 No dock devices found. ACPI: bus type pci registered PCI: Using MMCONFIG Setting up standard PCI resources evgpeblk-0956 [00] ev_create_gpe_block : GPE 00 to 1F [_GPE] 4 regs on int 0x9 evgpeblk-1052 [00] ev_initialize_gpe_bloc: Found 13 Wake, Enabled 2 Runtime GPEs in this block ACPI: EC: Look up EC in DSDT Completing Region/Field/Buffer/Package initialization:.................................................................... Initialized 34/39 Regions 5/5 Fields 9/9 Buffers 20/33 Packages (516 nodes) Initializing Device/Processor/Thermal objects by executing _INI methods:.<4>ACPI: System BIOS is requesting _OSI(Linux) ACPI: If "acpi_osi=Linux" works better, Please send dmidecode to linux-acpi@vger.kernel.org ..... Executed 6 _INI methods requiring 5 _STA executions (examined 51 objects) ACPI: Interpreter enabled ACPI: (supports S0 S1 S3 S5) ACPI: Using IOAPIC for interrupt routing ACPI: PCI Root Bridge [PCI0] (0000:00) PCI quirk: region 0800-087f claimed by ICH6 ACPI/GPIO/TCO PCI quirk: region 0880-08bf claimed by ICH6 GPIO PCI: Transparent bridge - 0000:00:1e.0 ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCI4._PRT] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCI2._PRT] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCI5._PRT] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 9 10 *11 12 15) ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 9 *10 11 12 15) ACPI: PCI Interrupt Link [LNKC] (IRQs *3 4 5 6 7 9 10 11 12 15) ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 9 10 11 12 15) *0, disabled. ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 *9 10 11 12 15) ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 9 10 11 12 15) *0, disabled. ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 7 *9 10 11 12 15) ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 *5 6 7 9 10 11 12 15) ACPI Warning (tbutils-0217): Incorrect checksum in table [TCPA] - 00, should be 89 [20070126] Linux Plug and Play Support v0.97 (c) Adam Belay pnp: PnP ACPI init ACPI: bus type pnp registered pnp: PnP ACPI: found 11 devices ACPI: ACPI bus type pnp unregistered SCSI subsystem initialized libata version 2.21 loaded. usbcore: registered new interface driver usbfs usbcore: registered new interface driver hub usbcore: registered new device driver usb PCI: Using ACPI for IRQ routing PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report Time: tsc clocksource has been installed. pnp: 00:01: ioport range 0x800-0x85f has been reserved pnp: 00:01: ioport range 0xc00-0xc7f has been reserved pnp: 00:01: ioport range 0x860-0x8ff could not be reserved pnp: 00:08: iomem range 0x0-0x9ffff could not be reserved pnp: 00:08: iomem range 0x100000-0xffffff could not be reserved pnp: 00:08: iomem range 0x1000000-0x3f5ffbff could not be reserved pnp: 00:08: iomem range 0xf0000-0xfffff could not be reserved pnp: 00:09: ioport range 0x100-0x1fe has been reserved pnp: 00:09: ioport range 0x200-0x277 has been reserved pnp: 00:09: ioport range 0x280-0x2e7 has been reserved pnp: 00:09: ioport range 0x2f0-0x2f7 has been reserved pnp: 00:09: ioport range 0x300-0x377 has been reserved pnp: 00:09: ioport range 0x380-0x3bb has been reserved pnp: 00:09: ioport range 0x3c0-0x3e7 could not be reserved pnp: 00:09: ioport range 0x3f6-0x3f7 has been reserved pnp: 00:09: iomem range 0xe0000000-0xefffffff could not be reserved pnp: 00:09: iomem range 0xfeda0000-0xfedacfff has been reserved PCI: Bridge: 0000:00:1c.0 IO window: disabled. MEM window: dfc00000-dfcfffff PREFETCH window: disabled. PCI: Bridge: 0000:00:1c.4 IO window: disabled. MEM window: dfb00000-dfbfffff PREFETCH window: disabled. PCI: Bridge: 0000:00:1e.0 IO window: disabled. MEM window: disabled. PREFETCH window: disabled. ACPI: PCI Interrupt 0000:00:1c.0[A] -> GSI 16 (level, low) -> IRQ 16 PCI: Setting latency timer of device 0000:00:1c.0 to 64 ACPI: PCI Interrupt 0000:00:1c.4[A] -> GSI 16 (level, low) -> IRQ 16 PCI: Setting latency timer of device 0000:00:1c.4 to 64 PCI: Setting latency timer of device 0000:00:1e.0 to 64 NET: Registered protocol family 2 IP route cache hash table entries: 32768 (order: 5, 131072 bytes) TCP established hash table entries: 131072 (order: 8, 1572864 bytes) TCP bind hash table entries: 65536 (order: 7, 524288 bytes) TCP: Hash tables configured (established 131072 bind 65536) TCP reno registered checking if image is initramfs... it is Freeing initrd memory: 817k freed Simple Boot Flag at 0x7a set to 0x80 Total HugeTLB memory allocated, 0 VFS: Disk quotas dquot_6.5.1 Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) Installing knfsd (copyright (C) 1996 okir@monad.swb.de). io scheduler noop registered io scheduler deadline registered io scheduler cfq registered (default) Boot video device is 0000:00:02.0 PCI: Setting latency timer of device 0000:00:1c.0 to 64 assign_interrupt_mode Found MSI capability Allocate Port Service[0000:00:1c.0:pcie00] Allocate Port Service[0000:00:1c.0:pcie02] Allocate Port Service[0000:00:1c.0:pcie03] PCI: Setting latency timer of device 0000:00:1c.4 to 64 assign_interrupt_mode Found MSI capability Allocate Port Service[0000:00:1c.4:pcie00] Allocate Port Service[0000:00:1c.4:pcie02] Allocate Port Service[0000:00:1c.4:pcie03] pci_hotplug: PCI Hot Plug PCI Core version: 0.5 acpiphp: ACPI Hot Plug PCI Controller Driver version: 0.5 acpiphp_glue: can't get bus number, assuming 0 pciehp: HPC vendor_id 8086 device_id 283f ss_vid 0 ss_did 0 pciehp: Cannot get control of hotplug hardware for pci 0000:00:1c.0 pciehp: HPC vendor_id 8086 device_id 2847 ss_vid 0 ss_did 0 pciehp: Cannot get control of hotplug hardware for pci 0000:00:1c.4 pciehp: PCI Express Hot Plug Controller Driver version: 0.4 input: Power Button (FF) as /class/input/input0 ACPI: Power Button (FF) [PWRF] input: Power Button (CM) as /class/input/input1 ACPI: Power Button (CM) [VBTN] ACPI Exception (processor_core-0818): AE_NOT_FOUND, Processor Device is not present [20070126] ACPI Exception (processor_core-0818): AE_NOT_FOUND, Processor Device is not present [20070126] Real Time Clock Driver v1.12ac hpet_resources: 0xfed00000 is busy Linux agpgart interface v0.102 agpgart: Detected an Intel 965Q Chipset. agpgart: Detected 7676K stolen memory. agpgart: AGP aperture is 256M @ 0xc0000000 Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A 00:07: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A floppy0: no floppy controllers found RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize loop: module loaded tg3.c:v3.81 (September 5, 2007) ACPI: PCI Interrupt 0000:02:00.0[A] -> GSI 16 (level, low) -> IRQ 16 PCI: Setting latency timer of device 0000:02:00.0 to 64 eth0: Tigon3 [partno(BCM95754) rev b002 PHY(5787)] (PCI Express) 10/100/1000Base-T Ethernet 00:18:8b:16:1a:0d eth0: RXcsums[1] LinkChgREG[0] MIirq[0] ASF[0] WireSpeed[1] TSOcap[1] eth0: dma_rwctrl[76180000] dma_mask[64-bit] netconsole: not configured, aborting Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2 ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx Probing IDE interface ide0... Probing IDE interface ide1... megaraid cmm: 2.20.2.7 (Release Date: Sun Jul 16 00:01:03 EST 2006) megaraid: 2.20.5.1 (Release Date: Thu Nov 16 15:32:35 EST 2006) megasas: 00.00.03.10-rc5 Thu May 17 10:09:32 PDT 2007 ata_piix 0000:00:1f.2: version 2.12 ata_piix 0000:00:1f.2: MAP [ P0 P2 P1 P3 ] ACPI: PCI Interrupt 0000:00:1f.2[C] -> GSI 20 (level, low) -> IRQ 17 PCI: Setting latency timer of device 0000:00:1f.2 to 64 scsi0 : ata_piix scsi1 : ata_piix ata1: SATA max UDMA/133 cmd 0x0001fe00 ctl 0x0001fe12 bmdma 0x0001fec0 irq 17 ata2: SATA max UDMA/133 cmd 0x0001fe20 ctl 0x0001fe32 bmdma 0x0001fec8 irq 17 ata1.00: ATA-7: ST3808110AS, 3.ADH, max UDMA/133 ata1.00: 156250000 sectors, multi 8: LBA48 NCQ (depth 0/32) ata1.00: configured for UDMA/133 ata2.00: ATAPI: HL-DT-ST CD-RW/DVD-ROM GCC-H10N, C101, max UDMA/100 ata2.00: configured for UDMA/100 ata2: EH pending after completion, repeating EH (cnt=4) scsi 0:0:0:0: Direct-Access ATA ST3808110AS 3.AD PQ: 0 ANSI: 5 sd 0:0:0:0: [sda] 156250000 512-byte hardware sectors (80000 MB) sd 0:0:0:0: [sda] Write Protect is off sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA sd 0:0:0:0: [sda] 156250000 512-byte hardware sectors (80000 MB) sd 0:0:0:0: [sda] Write Protect is off sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA sda: sda1 sda2 sda3 sda4 < sda5 sda6 > sd 0:0:0:0: [sda] Attached SCSI disk sd 0:0:0:0: Attached scsi generic sg0 type 0 scsi 1:0:0:0: CD-ROM HL-DT-ST CDRW/DVD GCCH10N C101 PQ: 0 ANSI: 5 sr0: scsi3-mmc drive: 48x/48x writer cd/rw xa/form2 cdda tray Uniform CD-ROM driver Revision: 3.20 sr 1:0:0:0: Attached scsi CD-ROM sr0 sr 1:0:0:0: Attached scsi generic sg1 type 5 ata_piix 0000:00:1f.5: MAP [ P0 P2 P1 P3 ] ACPI: PCI Interrupt 0000:00:1f.5[C] -> GSI 20 (level, low) -> IRQ 17 PCI: Setting latency timer of device 0000:00:1f.5 to 64 scsi2 : ata_piix scsi3 : ata_piix ata3: SATA max UDMA/133 cmd 0x0001fe40 ctl 0x0001fe52 bmdma 0x0001fed0 irq 17 ata4: SATA max UDMA/133 cmd 0x0001fe60 ctl 0x0001fe72 bmdma 0x0001fed8 irq 17 Fusion MPT base driver 3.04.05 Copyright (c) 1999-2007 LSI Logic Corporation Fusion MPT SPI Host driver 3.04.05 Fusion MPT SAS Host driver 3.04.05 ieee1394: raw1394: /dev/raw1394 device initialized ACPI: PCI Interrupt 0000:00:1a.7[C] -> GSI 22 (level, low) -> IRQ 18 PCI: Setting latency timer of device 0000:00:1a.7 to 64 ehci_hcd 0000:00:1a.7: EHCI Host Controller ehci_hcd 0000:00:1a.7: new USB bus registered, assigned bus number 1 ehci_hcd 0000:00:1a.7: debug port 1 PCI: cache line size of 128 is not supported by device 0000:00:1a.7 ehci_hcd 0000:00:1a.7: irq 18, io mem 0xdfdfbc00 ehci_hcd 0000:00:1a.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004 usb usb1: configuration #1 chosen from 1 choice hub 1-0:1.0: USB hub found hub 1-0:1.0: 4 ports detected ACPI: PCI Interrupt 0000:00:1d.7[A] -> GSI 23 (level, low) -> IRQ 19 PCI: Setting latency timer of device 0000:00:1d.7 to 64 ehci_hcd 0000:00:1d.7: EHCI Host Controller ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 2 ehci_hcd 0000:00:1d.7: debug port 1 PCI: cache line size of 128 is not supported by device 0000:00:1d.7 ehci_hcd 0000:00:1d.7: irq 19, io mem 0xff980800 ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004 usb usb2: configuration #1 chosen from 1 choice hub 2-0:1.0: USB hub found hub 2-0:1.0: 6 ports detected ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver usbcore: registered new interface driver usblp Initializing USB Mass Storage driver... usbcore: registered new interface driver usb-storage USB Mass Storage support registered. PNP: No PS/2 controller found. Probing ports directly. serio: i8042 KBD port at 0x60,0x64 irq 1 serio: i8042 AUX port at 0x60,0x64 irq 12 mice: PS/2 mouse device common for all mice device-mapper: ioctl: 4.11.0-ioctl (2006-10-12) initialised: dm-devel@redhat.com usbcore: registered new interface driver usbhid drivers/hid/usbhid/hid-core.c: v2.6:USB HID core driver oprofile: using NMI interrupt. TCP cubic registered NET: Registered protocol family 1 NET: Registered protocol family 10 IPv6 over IPv4 tunneling driver NET: Registered protocol family 17 Starting balanced_irq Using IPI No-Shortcut mode Freeing unused kernel memory: 244k freed kjournald starting. Commit interval 5 seconds EXT3-fs: mounted filesystem with ordered data mode. USB Universal Host Controller Interface driver v3.0 ACPI: PCI Interrupt 0000:00:1a.0[A] -> GSI 16 (level, low) -> IRQ 16 PCI: Setting latency timer of device 0000:00:1a.0 to 64 uhci_hcd 0000:00:1a.0: UHCI Host Controller uhci_hcd 0000:00:1a.0: new USB bus registered, assigned bus number 3 uhci_hcd 0000:00:1a.0: irq 16, io base 0x0000ff20 usb usb3: configuration #1 chosen from 1 choice hub 3-0:1.0: USB hub found hub 3-0:1.0: 2 ports detected ACPI: PCI Interrupt 0000:00:1a.1[B] -> GSI 17 (level, low) -> IRQ 20 PCI: Setting latency timer of device 0000:00:1a.1 to 64 uhci_hcd 0000:00:1a.1: UHCI Host Controller uhci_hcd 0000:00:1a.1: new USB bus registered, assigned bus number 4 uhci_hcd 0000:00:1a.1: irq 20, io base 0x0000ff00 usb usb4: configuration #1 chosen from 1 choice hub 4-0:1.0: USB hub found hub 4-0:1.0: 2 ports detected ACPI: PCI Interrupt 0000:00:1d.0[A] -> GSI 23 (level, low) -> IRQ 19 PCI: Setting latency timer of device 0000:00:1d.0 to 64 uhci_hcd 0000:00:1d.0: UHCI Host Controller uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 5 uhci_hcd 0000:00:1d.0: irq 19, io base 0x0000ff80 usb usb5: configuration #1 chosen from 1 choice hub 5-0:1.0: USB hub found hub 5-0:1.0: 2 ports detected ACPI: PCI Interrupt 0000:00:1d.1[B] -> GSI 17 (level, low) -> IRQ 20 PCI: Setting latency timer of device 0000:00:1d.1 to 64 uhci_hcd 0000:00:1d.1: UHCI Host Controller uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 6 uhci_hcd 0000:00:1d.1: irq 20, io base 0x0000ff60 usb usb6: configuration #1 chosen from 1 choice hub 6-0:1.0: USB hub found hub 6-0:1.0: 2 ports detected usb 3-2: new low speed USB device using uhci_hcd and address 2 ACPI: PCI Interrupt 0000:00:1d.2[C] -> GSI 18 (level, low) -> IRQ 21 PCI: Setting latency timer of device 0000:00:1d.2 to 64 uhci_hcd 0000:00:1d.2: UHCI Host Controller uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 7 uhci_hcd 0000:00:1d.2: irq 21, io base 0x0000ff40 usb usb7: configuration #1 chosen from 1 choice hub 7-0:1.0: USB hub found hub 7-0:1.0: 2 ports detected usb 3-2: configuration #1 chosen from 1 choice input: ATEN ATEN CS-1716/08/04 as /class/input/input2 input: USB HID v1.10 Keyboard [ATEN ATEN CS-1716/08/04] on usb-0000:00:1a.0-2 input: ATEN ATEN CS-1716/08/04 as /class/input/input3 input: USB HID v1.10 Mouse [ATEN ATEN CS-1716/08/04] on usb-0000:00:1a.0-2 EXT3 FS on sda2, internal journal kjournald starting. Commit interval 5 seconds EXT3 FS on sda1, internal journal EXT3-fs: mounted filesystem with ordered data mode. kjournald starting. Commit interval 5 seconds EXT3-fs warning: maximal mount count reached, running e2fsck is recommended EXT3 FS on sda6, internal journal EXT3-fs: mounted filesystem with ordered data mode. Adding 2096472k swap on /dev/sda3. Priority:-1 extents:1 across:2096472k ADDRCONF(NETDEV_UP): eth0: link is not ready tg3: eth0: Link is up at 100 Mbps, half duplex. tg3: eth0: Flow control is off for TX and off for RX. ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready eth0: no IPv6 routers present [drm] Initialized drm 1.1.0 20060810 ACPI: PCI Interrupt 0000:00:02.0[A] -> GSI 16 (level, low) -> IRQ 16 PCI: Setting latency timer of device 0000:00:02.0 to 64 [drm] Initialized i915 1.13.0 20080312 on minor 0 mtrr: type mismatch for c0000000,10000000 old: write-back new: write-combining glean[3258]: segfault at 00000000 eip 4698f68c esp bf89ac2c error 6