Linux version 2.6.27-gentoo (root@mail.mattsteven.com) (gcc version 3.4.6 (Gentoo Hardened 3.4.6-r2 p1.5, ssp-3.4.6-1.0, pie-8.7.10)) #2 SMP Fri Oct 24 08:53:45 CDT 2008 BIOS-provided physical RAM map: BIOS-e820: 0000000000000000 - 000000000008f000 (usable) BIOS-e820: 000000000008f000 - 00000000000a0000 (reserved) BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved) BIOS-e820: 0000000000100000 - 000000003f533000 (usable) BIOS-e820: 000000003f533000 - 000000003f53b000 (reserved) BIOS-e820: 000000003f53b000 - 000000003f5cb000 (usable) BIOS-e820: 000000003f5cb000 - 000000003f5cf000 (reserved) BIOS-e820: 000000003f5cf000 - 000000003f660000 (usable) BIOS-e820: 000000003f660000 - 000000003f6f0000 (ACPI NVS) BIOS-e820: 000000003f6f0000 - 000000003f6f2000 (usable) BIOS-e820: 000000003f6f2000 - 000000003f6ff000 (ACPI data) BIOS-e820: 000000003f6ff000 - 000000003f700000 (usable) BIOS-e820: 000000003f700000 - 0000000040000000 (reserved) BIOS-e820: 00000000f0000000 - 0000000100000000 (reserved) last_pfn = 0x3f700 max_arch_pfn = 0x100000 kernel direct mapping tables up to 38000000 @ 7000-c000 RAMDISK: 37de3000 - 37fefc19 DMI 2.4 present. ACPI: RSDP 000FE020, 0014 (r0 INTEL ) ACPI: RSDT 3F6FD038, 003C (r1 INTEL D945GLF2 63 1000013) ACPI: FACP 3F6FC000, 0074 (r1 INTEL D945GLF2 63 MSFT 1000013) ACPI: DSDT 3F6F7000, 4787 (r1 INTEL D945GLF2 63 MSFT 1000013) ACPI: FACS 3F6A3000, 0040 ACPI: APIC 3F6F6000, 0078 (r1 INTEL D945GLF2 63 MSFT 1000013) ACPI: WDDT 3F6F5000, 0040 (r1 INTEL D945GLF2 63 MSFT 1000013) ACPI: MCFG 3F6F4000, 003C (r1 INTEL D945GLF2 63 MSFT 1000013) ACPI: ASF! 3F6F3000, 00A6 (r32 INTEL D945GLF2 63 MSFT 1000013) ACPI: HPET 3F6F2000, 0038 (r1 INTEL D945GLF2 63 MSFT 1000013) 119MB HIGHMEM available. 896MB LOWMEM available. mapped low ram: 0 - 38000000 low ram: 00000000 - 38000000 bootmap 00008000 - 0000f000 (9 early reservations) ==> bootmem [0000000000 - 0038000000] #0 [0000000000 - 0000001000] BIOS data page ==> [0000000000 - 0000001000] #1 [0000001000 - 0000002000] EX TRAMPOLINE ==> [0000001000 - 0000002000] #2 [0000006000 - 0000007000] TRAMPOLINE ==> [0000006000 - 0000007000] #3 [0000100000 - 0000557b54] TEXT DATA BSS ==> [0000100000 - 0000557b54] #4 [0037de3000 - 0037fefc19] RAMDISK ==> [0037de3000 - 0037fefc19] #5 [0000558000 - 000055b000] INIT_PG_TABLE ==> [0000558000 - 000055b000] #6 [000009fc00 - 0000100000] BIOS reserved ==> [000009fc00 - 0000100000] #7 [0000007000 - 0000008000] PGTABLE ==> [0000007000 - 0000008000] #8 [0000008000 - 000000f000] BOOTMAP ==> [0000008000 - 000000f000] Zone PFN ranges: DMA 0x00000000 -> 0x00001000 Normal 0x00001000 -> 0x00038000 HighMem 0x00038000 -> 0x0003f700 Movable zone start PFN for each node early_node_map[6] active PFN ranges 0: 0x00000000 -> 0x0000008f 0: 0x00000100 -> 0x0003f533 0: 0x0003f53b -> 0x0003f5cb 0: 0x0003f5cf -> 0x0003f660 0: 0x0003f6f0 -> 0x0003f6f2 0: 0x0003f6ff -> 0x0003f700 On node 0 totalpages: 259558 free_area_init_node: node 0, pgdat c04bd700, node_mem_map c1000000 DMA zone: 3951 pages, LIFO batch:0 Normal zone: 223520 pages, LIFO batch:31 HighMem zone: 30057 pages, LIFO batch:7 ACPI: PM-Timer IO Port: 0x408 ACPI: Local APIC address 0xfee00000 ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled) ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] enabled) ACPI: LAPIC (acpi_id[0x03] lapic_id[0x82] disabled) ACPI: LAPIC (acpi_id[0x04] lapic_id[0x83] disabled) ACPI: LAPIC_NMI (acpi_id[0x01] dfl dfl lint[0x1]) ACPI: LAPIC_NMI (acpi_id[0x02] dfl dfl lint[0x1]) ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0]) IOAPIC[0]: apic_id 2, version 32, address 0xfec00000, GSI 0-23 ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl) ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level) ACPI: IRQ0 used by override. ACPI: IRQ2 used by override. ACPI: IRQ9 used by override. Enabling APIC mode: Flat. Using 1 I/O APICs ACPI: HPET id: 0x8086a201 base: 0xfed00000 SMP: Allowing 4 CPUs, 2 hotplug CPUs mapped APIC to ffffb000 (fee00000) mapped IOAPIC to ffffa000 (fec00000) Allocating PCI resources starting at 50000000 (gap: 40000000:b0000000) PERCPU: Allocating 37532 bytes of per cpu data NR_CPUS: 6, nr_cpu_ids: 4, nr_node_ids 1 Built 1 zonelists in Zone order, mobility grouping on. Total pages: 257528 Kernel command line: root=/dev/ram0 lvm2root=/dev/disks/root ro panic=10 ramdisk_size=6000 Enabling fast FPU save and restore... done. Enabling unmasked SIMD FPU exception support... done. Initializing CPU#0 PID hash table entries: 4096 (order: 12, 16384 bytes) TSC: PIT calibration confirmed by PMTIMER. TSC: using PMTIMER calibration value Detected 1596.077 MHz processor. Console: colour VGA+ 80x25 console [tty0] enabled Dentry cache hash table entries: 131072 (order: 7, 524288 bytes) Inode-cache hash table entries: 65536 (order: 6, 262144 bytes) Memory: 1022180k/1039360k available (2802k kernel code, 15688k reserved, 1092k data, 228k init, 121180k highmem) virtual kernel memory layout: fixmap : 0xfff6b000 - 0xfffff000 ( 592 kB) pkmap : 0xff800000 - 0xffc00000 (4096 kB) vmalloc : 0xf8800000 - 0xff7fe000 ( 111 MB) lowmem : 0xc0000000 - 0xf8000000 ( 896 MB) .init : 0xc04d4000 - 0xc050d000 ( 228 kB) .data : 0xc03bc9e5 - 0xc04cdc74 (1092 kB) .text : 0xc0100000 - 0xc03bc9e5 (2802 kB) Checking if this processor honours the WP bit even in supervisor mode...Ok. CPA: page pool initialized 1 of 1 pages preallocated hpet clockevent registered Calibrating delay loop (skipped), value calculated using timer frequency.. 3192.15 BogoMIPS (lpj=6384308) Mount-cache hash table entries: 512 CPU: L1 I cache: 32K, L1 D cache: 24K CPU: L2 cache: 512K CPU: Physical Processor ID: 0 CPU: Processor Core ID: 0 Intel machine check architecture supported. Intel machine check reporting enabled on CPU#0. using mwait in idle threads. Checking 'hlt' instruction... OK. ACPI: Core revision 20080609 ENABLING IO-APIC IRQs ..TIMER: vector=0x31 apic1=0 pin1=2 apic2=-1 pin2=-1 CPU0: Intel(R) Atom(TM) CPU 330 @ 1.60GHz stepping 02 Booting processor 1/1 ip 6000 Initializing CPU#1 Calibrating delay using timer specific routine.. 3192.18 BogoMIPS (lpj=6384373) CPU: L1 I cache: 32K, L1 D cache: 24K CPU: L2 cache: 512K CPU: Physical Processor ID: 0 CPU: Processor Core ID: 1 Intel machine check architecture supported. Intel machine check reporting enabled on CPU#1. CPU1: Intel(R) Atom(TM) CPU 330 @ 1.60GHz stepping 02 checking TSC synchronization [CPU#0 -> CPU#1]: passed. Brought up 2 CPUs Total of 2 processors activated (6384.34 BogoMIPS). CPU0 attaching sched-domain: domain 0: span 0-1 level CPU groups: 0 1 CPU1 attaching sched-domain: domain 0: span 0-1 level CPU groups: 1 0 net_namespace: 596 bytes NET: Registered protocol family 16 No dock devices found. ACPI: bus type pci registered PCI: Found Intel Corporation 945G/GZ/P/PL Express Memory Controller Hub without MMCONFIG support. PCI: Using configuration type 1 for base access ACPI: EC: Look up EC in DSDT ACPI: Interpreter enabled ACPI: (supports S0 S1 S3 S5) ACPI: Using IOAPIC for interrupt routing ACPI: PCI Root Bridge [PCI0] (0000:00) PCI: 0000:00:02.0 reg 10 32bit mmio: [48200000, 4827ffff] PCI: 0000:00:02.0 reg 14 io port: [20e0, 20e7] PCI: 0000:00:02.0 reg 18 32bit mmio: [40000000, 47ffffff] PCI: 0000:00:02.0 reg 1c 32bit mmio: [48280000, 4829ffff] PCI: 0000:00:1b.0 reg 10 64bit mmio: [482a0000, 482a3fff] pci 0000:00:1b.0: PME# supported from D0 D3hot D3cold pci 0000:00:1b.0: PME# disabled pci 0000:00:1c.0: PME# supported from D0 D3hot D3cold pci 0000:00:1c.0: PME# disabled pci 0000:00:1c.2: PME# supported from D0 D3hot D3cold pci 0000:00:1c.2: PME# disabled pci 0000:00:1c.3: PME# supported from D0 D3hot D3cold pci 0000:00:1c.3: PME# disabled PCI: 0000:00:1d.0 reg 20 io port: [2080, 209f] PCI: 0000:00:1d.1 reg 20 io port: [2060, 207f] PCI: 0000:00:1d.2 reg 20 io port: [2040, 205f] PCI: 0000:00:1d.3 reg 20 io port: [2020, 203f] PCI: 0000:00:1d.7 reg 10 32bit mmio: [482a4000, 482a43ff] pci 0000:00:1d.7: PME# supported from D0 D3hot D3cold pci 0000:00:1d.7: PME# disabled pci 0000:00:1f.0: quirk: region 0400-047f claimed by ICH6 ACPI/GPIO/TCO pci 0000:00:1f.0: quirk: region 0500-053f claimed by ICH6 GPIO PCI: 0000:00:1f.1 reg 10 io port: [20d8, 20df] PCI: 0000:00:1f.1 reg 14 io port: [20f4, 20f7] PCI: 0000:00:1f.1 reg 18 io port: [20d0, 20d7] PCI: 0000:00:1f.1 reg 1c io port: [20f0, 20f3] PCI: 0000:00:1f.1 reg 20 io port: [20b0, 20bf] PCI: 0000:00:1f.2 reg 10 io port: [20c8, 20cf] PCI: 0000:00:1f.2 reg 14 io port: [20ec, 20ef] PCI: 0000:00:1f.2 reg 18 io port: [20c0, 20c7] PCI: 0000:00:1f.2 reg 1c io port: [20e8, 20eb] PCI: 0000:00:1f.2 reg 20 io port: [20a0, 20af] pci 0000:00:1f.2: PME# supported from D3hot pci 0000:00:1f.2: PME# disabled PCI: 0000:00:1f.3 reg 20 io port: [2000, 201f] PCI: 0000:01:00.0 reg 10 io port: [1000, 10ff] PCI: 0000:01:00.0 reg 18 64bit mmio: [48100000, 48100fff] PCI: 0000:01:00.0 reg 20 32bit mmio: [48000000, 4800ffff] PCI: 0000:01:00.0 reg 30 32bit mmio: [fffe0000, ffffffff] pci 0000:01:00.0: supports D1 pci 0000:01:00.0: supports D2 pci 0000:01:00.0: PME# supported from D0 D1 D2 D3hot D3cold pci 0000:01:00.0: PME# disabled PCI: bridge 0000:00:1c.0 io port: [1000, 1fff] PCI: bridge 0000:00:1c.0 32bit mmio: [48100000, 481fffff] PCI: bridge 0000:00:1c.0 64bit mmio pref: [48000000, 480fffff] pci 0000:00:1e.0: transparent bridge bus 00 -> node 0 ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P32_._PRT] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX0._PRT] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX2._PRT] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX3._PRT] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 7 9 10 *11 12) ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 7 9 10 11 12) *0, disabled. ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 7 *9 10 11 12) ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 7 9 10 *11 12) ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 7 9 10 11 12) *0, disabled. ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 7 9 10 11 12) *0, disabled. ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 7 *9 10 11 12) ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 7 9 *10 11 12) Linux Plug and Play Support v0.97 (c) Adam Belay pnp: PnP ACPI init ACPI: bus type pnp registered pnp: PnP ACPI: found 10 devices ACPI: ACPI bus type pnp unregistered SCSI subsystem initialized libata version 3.00 loaded. usbcore: registered new interface driver usbfs usbcore: registered new interface driver hub usbcore: registered new device driver usb PCI: Using ACPI for IRQ routing system 00:01: iomem range 0xf0000000-0xf3ffffff could not be reserved system 00:01: iomem range 0xfed13000-0xfed13fff could not be reserved system 00:01: iomem range 0xfed14000-0xfed17fff could not be reserved system 00:01: iomem range 0xfed18000-0xfed18fff could not be reserved system 00:01: iomem range 0xfed19000-0xfed19fff could not be reserved system 00:01: iomem range 0xfed1c000-0xfed1ffff could not be reserved system 00:01: iomem range 0xfed20000-0xfed3ffff could not be reserved system 00:01: iomem range 0xfed45000-0xfed99fff could not be reserved system 00:01: iomem range 0xc0000-0xdffff could not be reserved system 00:01: iomem range 0xe0000-0xfffff could not be reserved system 00:06: ioport range 0x500-0x53f has been reserved system 00:06: ioport range 0x400-0x47f has been reserved system 00:06: ioport range 0x680-0x6ff has been reserved pci 0000:00:1c.0: PCI bridge, secondary bus 0000:01 pci 0000:00:1c.0: IO window: 0x1000-0x1fff pci 0000:00:1c.0: MEM window: 0x48100000-0x481fffff pci 0000:00:1c.0: PREFETCH window: 0x00000048000000-0x000000480fffff pci 0000:00:1c.2: PCI bridge, secondary bus 0000:02 pci 0000:00:1c.2: IO window: disabled pci 0000:00:1c.2: MEM window: disabled pci 0000:00:1c.2: PREFETCH window: disabled pci 0000:00:1c.3: PCI bridge, secondary bus 0000:03 pci 0000:00:1c.3: IO window: disabled pci 0000:00:1c.3: MEM window: disabled pci 0000:00:1c.3: PREFETCH window: disabled pci 0000:00:1e.0: PCI bridge, secondary bus 0000:04 pci 0000:00:1e.0: IO window: disabled pci 0000:00:1e.0: MEM window: disabled pci 0000:00:1e.0: PREFETCH window: disabled pci 0000:00:1c.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17 pci 0000:00:1c.0: setting latency timer to 64 pci 0000:00:1c.2: PCI INT C -> GSI 18 (level, low) -> IRQ 18 pci 0000:00:1c.2: setting latency timer to 64 pci 0000:00:1c.3: PCI INT D -> GSI 19 (level, low) -> IRQ 19 pci 0000:00:1c.3: setting latency timer to 64 pci 0000:00:1e.0: setting latency timer to 64 bus: 00 index 0 io port: [0, ffff] bus: 00 index 1 mmio: [0, ffffffff] bus: 01 index 0 io port: [1000, 1fff] bus: 01 index 1 mmio: [48100000, 481fffff] bus: 01 index 2 mmio: [48000000, 480fffff] bus: 01 index 3 mmio: [0, 0] bus: 02 index 0 mmio: [0, 0] bus: 02 index 1 mmio: [0, 0] bus: 02 index 2 mmio: [0, 0] bus: 02 index 3 mmio: [0, 0] bus: 03 index 0 mmio: [0, 0] bus: 03 index 1 mmio: [0, 0] bus: 03 index 2 mmio: [0, 0] bus: 03 index 3 mmio: [0, 0] bus: 04 index 0 mmio: [0, 0] bus: 04 index 1 mmio: [0, 0] bus: 04 index 2 mmio: [0, 0] bus: 04 index 3 io port: [0, ffff] bus: 04 index 4 mmio: [0, ffffffff] NET: Registered protocol family 2 IP route cache hash table entries: 32768 (order: 5, 131072 bytes) TCP established hash table entries: 131072 (order: 8, 1048576 bytes) TCP bind hash table entries: 65536 (order: 7, 524288 bytes) TCP: Hash tables configured (established 131072 bind 65536) TCP reno registered NET: Registered protocol family 1 checking if image is initramfs...it isn't (no cpio magic); looks like an initrd Freeing initrd memory: 2099k freed Machine check exception polling timer started. audit: initializing netlink socket (disabled) type=2000 audit(1224904102.404:1): initialized highmem bounce pool size: 64 pages Installing knfsd (copyright (C) 1996 okir@monad.swb.de). SGI XFS with security attributes, realtime, no debug enabled SGI XFS Quota Management subsystem msgmni has been set to 1764 io scheduler noop registered io scheduler anticipatory registered (default) io scheduler deadline registered io scheduler cfq registered pci 0000:00:02.0: Boot video device intel_rng: Firmware space is locked read-only. If you can't or intel_rng: don't want to disable this in firmware setup, and if intel_rng: you are certain that your system has a functional intel_rng: RNG, try using the 'no_fwh_detect' option. Serial: 8250/16550 driver4 ports, IRQ sharing disabled brd: module loaded loop: module loaded usbcore: registered new interface driver asix usbcore: registered new interface driver cdc_ether usbcore: registered new interface driver net1080 usbcore: registered new interface driver zaurus Driver 'sd' needs updating - please use bus_type methods Driver 'sr' needs updating - please use bus_type methods ata_piix 0000:00:1f.1: version 2.12 ata_piix 0000:00:1f.1: PCI INT A -> GSI 18 (level, low) -> IRQ 18 ata_piix 0000:00:1f.1: setting latency timer to 64 scsi0 : ata_piix scsi1 : ata_piix ata1: PATA max UDMA/100 cmd 0x1f0 ctl 0x3f6 bmdma 0x20b0 irq 14 ata2: PATA max UDMA/100 cmd 0x170 ctl 0x376 bmdma 0x20b8 irq 15 Switched to high resolution mode on CPU 1 Switched to high resolution mode on CPU 0 ata1.00: ATAPI: _NEC DVD_RW ND-1300A, 1.0A, max UDMA/33 ata1.00: configured for UDMA/33 ata2: port disabled. ignoring. scsi 0:0:0:0: CD-ROM _NEC DVD_RW ND-1300A 1.0A PQ: 0 ANSI: 5 sr0: scsi3-mmc drive: 40x/40x writer cd/rw xa/form2 cdda tray Uniform CD-ROM driver Revision: 3.20 sr 0:0:0:0: Attached scsi CD-ROM sr0 sr 0:0:0:0: Attached scsi generic sg0 type 5 ata_piix 0000:00:1f.2: PCI INT B -> GSI 19 (level, low) -> IRQ 19 ata_piix 0000:00:1f.2: MAP [ P0 P2 P1 P3 ] ata_piix 0000:00:1f.2: setting latency timer to 64 scsi2 : ata_piix scsi3 : ata_piix ata3: SATA max UDMA/133 cmd 0x20c8 ctl 0x20ec bmdma 0x20a0 irq 19 ata4: SATA max UDMA/133 cmd 0x20c0 ctl 0x20e8 bmdma 0x20a8 irq 19 ata3.00: ATA-7: WDC WD5000AAKS-00TMA0, 12.01C01, max UDMA/133 ata3.00: 976773168 sectors, multi 16: LBA48 NCQ (depth 0/32) ata3.00: configured for UDMA/133 ata4.00: ATA-7: WDC WD5000AAKS-00TMA0, 12.01C01, max UDMA/133 ata4.00: 976773168 sectors, multi 16: LBA48 NCQ (depth 0/32) ata4.00: configured for UDMA/133 scsi 2:0:0:0: Direct-Access ATA WDC WD5000AAKS-0 12.0 PQ: 0 ANSI: 5 sd 2:0:0:0: [sda] 976773168 512-byte hardware sectors (500108 MB) sd 2:0:0:0: [sda] Write Protect is off sd 2:0:0:0: [sda] Mode Sense: 00 3a 00 00 sd 2:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA sd 2:0:0:0: [sda] 976773168 512-byte hardware sectors (500108 MB) sd 2:0:0:0: [sda] Write Protect is off sd 2:0:0:0: [sda] Mode Sense: 00 3a 00 00 sd 2:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA sda: sda1 sda2 sd 2:0:0:0: [sda] Attached SCSI disk sd 2:0:0:0: Attached scsi generic sg1 type 0 scsi 3:0:0:0: Direct-Access ATA WDC WD5000AAKS-0 12.0 PQ: 0 ANSI: 5 sd 3:0:0:0: [sdb] 976773168 512-byte hardware sectors (500108 MB) sd 3:0:0:0: [sdb] Write Protect is off sd 3:0:0:0: [sdb] Mode Sense: 00 3a 00 00 sd 3:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA sd 3:0:0:0: [sdb] 976773168 512-byte hardware sectors (500108 MB) sd 3:0:0:0: [sdb] Write Protect is off sd 3:0:0:0: [sdb] Mode Sense: 00 3a 00 00 sd 3:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA sdb: sdb1 sdb2 sd 3:0:0:0: [sdb] Attached SCSI disk sd 3:0:0:0: Attached scsi generic sg2 type 0 USB Universal Host Controller Interface driver v3.0 uhci_hcd 0000:00:1d.0: PCI INT A -> GSI 23 (level, low) -> IRQ 23 uhci_hcd 0000:00:1d.0: setting latency timer to 64 uhci_hcd 0000:00:1d.0: UHCI Host Controller uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 1 uhci_hcd 0000:00:1d.0: irq 23, io base 0x00002080 usb usb1: configuration #1 chosen from 1 choice hub 1-0:1.0: USB hub found hub 1-0:1.0: 2 ports detected uhci_hcd 0000:00:1d.1: PCI INT B -> GSI 19 (level, low) -> IRQ 19 uhci_hcd 0000:00:1d.1: setting latency timer to 64 uhci_hcd 0000:00:1d.1: UHCI Host Controller uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 2 uhci_hcd 0000:00:1d.1: irq 19, io base 0x00002060 usb usb2: configuration #1 chosen from 1 choice hub 2-0:1.0: USB hub found hub 2-0:1.0: 2 ports detected usb 1-1: new low speed USB device using uhci_hcd and address 2 uhci_hcd 0000:00:1d.2: PCI INT C -> GSI 18 (level, low) -> IRQ 18 uhci_hcd 0000:00:1d.2: setting latency timer to 64 uhci_hcd 0000:00:1d.2: UHCI Host Controller uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 3 uhci_hcd 0000:00:1d.2: irq 18, io base 0x00002040 usb usb3: configuration #1 chosen from 1 choice hub 3-0:1.0: USB hub found hub 3-0:1.0: 2 ports detected usb 1-1: configuration #1 chosen from 1 choice usb 2-1: new full speed USB device using uhci_hcd and address 2 uhci_hcd 0000:00:1d.3: PCI INT D -> GSI 16 (level, low) -> IRQ 16 uhci_hcd 0000:00:1d.3: setting latency timer to 64 uhci_hcd 0000:00:1d.3: UHCI Host Controller uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 4 uhci_hcd 0000:00:1d.3: irq 16, io base 0x00002020 usb usb4: configuration #1 chosen from 1 choice hub 4-0:1.0: USB hub found hub 4-0:1.0: 2 ports detected usb 2-1: configuration #1 chosen from 1 choice usb 2-2: new full speed USB device using uhci_hcd and address 3 usb 2-2: configuration #1 chosen from 1 choice usb 3-2: new full speed USB device using uhci_hcd and address 2 usb 3-2: configuration #1 chosen from 1 choice usblp0: USB Bidirectional printer dev 2 if 0 alt 0 proto 2 vid 0x04F9 pid 0x0162 usbcore: registered new interface driver usblp Initializing USB Mass Storage driver... scsi4 : SCSI emulation for USB Mass Storage devices usb-storage: device found at 2 usb-storage: waiting for device to settle before scanning usbcore: registered new interface driver usb-storage USB Mass Storage support registered. PNP: PS/2 Controller [PNP0303:PS2K] at 0x60,0x64 irq 1 PNP: PS/2 appears to have AUX port disabled, if this is incorrect please boot with i8042.nopnp serio: i8042 KBD port at 0x60,0x64 irq 1 mice: PS/2 mouse device common for all mice I2O subsystem v1.325 i2o: max drivers = 8 I2O Configuration OSM v1.323 I2O Block Device OSM v1.325 I2O SCSI Peripheral OSM v1.316 I2O ProcFS OSM v1.316 i2c /dev entries driver device-mapper: ioctl: 4.14.0-ioctl (2008-04-23) initialised: dm-devel@redhat.com device-mapper: multipath: version 1.0.5 loaded device-mapper: multipath round-robin: version 1.0.0 loaded cpuidle: using governor ladder usbcore: registered new interface driver hiddev usbcore: registered new interface driver usbhid usbhid: v2.6:USB HID core driver TCP cubic registered NET: Registered protocol family 17 RPC: Registered udp transport module. RPC: Registered tcp transport module. Starting balanced_irq Using IPI No-Shortcut mode input: AT Translated Set 2 keyboard as /class/input/input0 RAMDISK: Compressed image found at block 0 VFS: Mounted root (ext2 filesystem) readonly. Freeing unused kernel memory: 228k freed Write protecting the kernel text: 2804k Write protecting the kernel read-only data: 884k UDF-fs: No VRS found Filesystem "dm-0": Disabling barriers, trial barrier write failed XFS mounting filesystem dm-0 Ending clean XFS mount for filesystem: dm-0 Linux agpgart interface v0.103 agpgart-intel 0000:00:00.0: Intel 945G Chipset agpgart-intel 0000:00:00.0: detected 8060K stolen memory processor ACPI0007:00: registered as cooling_device0 processor ACPI0007:01: registered as cooling_device1 agpgart-intel 0000:00:00.0: AGP aperture is 128M @ 0x40000000 input: Power Button (FF) as /class/input/input1 ACPI: Power Button (FF) [PWRF] input: Sleep Button (CM) as /class/input/input2 ACPI: Sleep Button (CM) [SLPB] r8169 Gigabit Ethernet driver 2.3LK-NAPI loaded r8169 0000:01:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 r8169 0000:01:00.0: setting latency timer to 64 r8169 0000:01:00.0: no MSI. Back to INTx. eth0: RTL8168c/8111c at 0xf8876000, 00:1c:c0:70:6d:4a, XID 3c4000c0 IRQ 16 input: X10 Wireless Technology Inc USB Receiver as /class/input/input3 ehci_hcd 0000:00:1d.7: PCI INT A -> GSI 23 (level, low) -> IRQ 23 ehci_hcd 0000:00:1d.7: setting latency timer to 64 ehci_hcd 0000:00:1d.7: EHCI Host Controller ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 5 ehci_hcd 0000:00:1d.7: debug port 1 ehci_hcd 0000:00:1d.7: cache line size of 32 is not supported ehci_hcd 0000:00:1d.7: irq 23, io mem 0x482a4000 NET: Registered protocol family 8 NET: Registered protocol family 20 ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004 usb usb5: configuration #1 chosen from 1 choice hub 5-0:1.0: USB hub found hub 5-0:1.0: 8 ports detected usb 1-1: USB disconnect, address 2 ati_remote 1-1:1.0: ati_remote_open: usb_submit_urb failed! input: failed to attach handler kbd to device input3, error: -5 HDA Intel 0000:00:1b.0: PCI INT A -> GSI 22 (level, low) -> IRQ 22 HDA Intel 0000:00:1b.0: setting latency timer to 64 hda_codec: Unknown model for ALC662, trying auto-probe from BIOS... [ueagle-atm] driver ueagle 1.4 loaded i801_smbus 0000:00:1f.3: PCI INT B -> GSI 19 (level, low) -> IRQ 19 ACPI: I/O resource 0000:00:1f.3 [0x2000-0x201f] conflicts with ACPI region SMB1 [0x2000-0x2016] ACPI: Device needs an ACPI driver usb 2-1: USB disconnect, address 2 usblp0: removed Linux video capture interface: v2.00 em28xx v4l2 driver version 0.1.0 loaded usb 2-2: USB disconnect, address 3 usb 3-2: USB disconnect, address 2 usb 5-2: new high speed USB device using ehci_hcd and address 3 usb 5-2: configuration #1 chosen from 1 choice scsi5 : SCSI emulation for USB Mass Storage devices usb-storage: device found at 3 usb-storage: waiting for device to settle before scanning usb 5-6: new high speed USB device using ehci_hcd and address 6 usb 5-6: configuration #1 chosen from 1 choice usbcore: registered new interface driver ati_remote ati_remote: Registered USB driver ATI/X10 RF USB Remote Control v. 2.2.1 em28xx new video device (2040:6513): interface 0, class 255 em28xx Doesn't have usb audio class em28xx #0: Alternate settings: 8 em28xx #0: Alternate setting 0, max size= 0 em28xx #0: Alternate setting 1, max size= 0 em28xx #0: Alternate setting 2, max size= 1448 em28xx #0: Alternate setting 3, max size= 2048 em28xx #0: Alternate setting 4, max size= 2304 em28xx #0: Alternate setting 5, max size= 2580 em28xx #0: Alternate setting 6, max size= 2892 em28xx #0: Alternate setting 7, max size= 3072 usbcore: registered new interface driver ueagle-atm em28xx #0: chip ID is em2882/em2883 em28xx #0: i2c eeprom 00: 1a eb 67 95 40 20 13 65 d0 12 5c 03 82 1e 6a 18 em28xx #0: i2c eeprom 10: 00 00 24 57 66 07 01 00 00 00 00 00 00 00 00 00 em28xx #0: i2c eeprom 20: 46 00 01 00 f0 10 02 00 b8 00 00 00 5b 1c 00 00 em28xx #0: i2c eeprom 30: 00 00 20 40 20 80 02 20 01 01 01 01 00 00 00 00 em28xx #0: i2c eeprom 40: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 em28xx #0: i2c eeprom 50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 em28xx #0: i2c eeprom 60: 00 00 00 00 00 00 00 00 00 00 18 03 34 00 30 00 em28xx #0: i2c eeprom 70: 32 00 38 00 35 00 32 00 36 00 31 00 38 00 30 00 em28xx #0: i2c eeprom 80: 00 00 1e 03 57 00 69 00 6e 00 54 00 56 00 20 00 em28xx #0: i2c eeprom 90: 48 00 56 00 52 00 2d 00 39 00 38 00 30 00 00 00 em28xx #0: i2c eeprom a0: 84 12 00 00 05 50 1a 7f d4 78 23 b1 fe d0 18 85 em28xx #0: i2c eeprom b0: ff 00 00 00 04 84 0a 00 01 01 20 77 00 40 64 6e em28xx #0: i2c eeprom c0: 1e f0 74 02 01 00 01 79 b6 00 00 00 00 00 00 00 em28xx #0: i2c eeprom d0: 84 12 00 00 05 50 1a 7f d4 78 23 b1 fe d0 18 85 em28xx #0: i2c eeprom e0: ff 00 00 00 04 84 0a 00 01 01 20 77 00 40 64 6e em28xx #0: i2c eeprom f0: 1e f0 74 02 01 00 01 79 b6 00 00 00 00 00 00 00 EEPROM ID= 0x9567eb1a, hash = 0x031f24dd Vendor/Product ID= 2040:6513 AC97 audio (5 sample rates) 500mA max power Table at 0x24, strings=0x1e82, 0x186a, 0x0000 tveeprom 1-0050: Hauppauge model 65201, rev A1C0, serial# 1994340 tveeprom 1-0050: tuner model is Xceive XC3028 (idx 120, type 71) tveeprom 1-0050: TV standards PAL(B/G) PAL(I) PAL(D/D1/K) ATSC/DVB Digital (eeprom 0xd4) tveeprom 1-0050: audio processor is None (idx 0) tveeprom 1-0050: has radio tuner' 1-0061: chip found @ 0xc2 (em28xx #0) usb 1-1: new low speed USB device using uhci_hcd and address 3 xc2028 1-0061: creating new instance xc2028 1-0061: type set to XCeive xc2028/xc3028 tuner firmware: requesting xc3028-v27.fw xc2028 1-0061: Loading 80 firmware images from xc3028-v27.fw, type: xc2028 firmware, ver 2.7 xc2028 1-0061: Loading firmware for type=BASE MTS (5), id 0000000000000000. usb 1-1: configuration #1 chosen from 1 choice input: X10 Wireless Technology Inc USB Receiver as /class/input/input4 ati_remote: Weird data, len=1 ff 00 00 00 14 20 ... usb 2-1: new full speed USB device using uhci_hcd and address 4 usb 2-1: configuration #1 chosen from 1 choice usblp0: USB Bidirectional printer dev 4 if 0 alt 0 proto 2 vid 0x04F9 pid 0x0162 scsi6 : SCSI emulation for USB Mass Storage devices usb-storage: device found at 4 usb-storage: waiting for device to settle before scanning usb 2-2: new full speed USB device using uhci_hcd and address 5 usb 2-2: configuration #1 chosen from 1 choice xc2028 1-0061: Loading firmware for type=MTS (4), id ffffffffffffffff. usb 2-2: [ueagle-atm] ADSL device founded vid (0X1110) pid (0X900F) Rev (0X410B): Eagle I usb 2-2: reset full speed USB device using uhci_hcd and address 5 tvp5150 1-005c: tvp5150am1 detected. usb 2-2: [ueagle-atm] using iso mode usb 2-2: [ueagle-atm] (re)booting started em28xx #0: V4L2 device registered as /dev/video0 and /dev/vbi0 em28xx #0: Found Hauppauge WinTV HVR 950 usbcore: registered new interface driver em28xx em28xx-audio.c: probing for em28x1 non standard usbaudio em28xx-audio.c: Copyright (C) 2006 Markus Rechberger Em28xx: Initialized (Em28xx Audio Extension) extension xc2028 1-0061: attaching existing instance xc2028 1-0061: type set to XCeive xc2028/xc3028 tuner em28xx #0/2: xc3028 attached DVB: registering new adapter (em28xx #0) DVB: registering frontend 0 (LG Electronics LGDT3303 VSB/QAM Frontend)... Successfully loaded em28xx-dvb Em28xx: Initialized (Em28xx dvb Extension) extension firmware: requesting ueagle-atm/DSPep.bin usb 2-2: [ueagle-atm] ATU-R firmware version : 44e2ea17 firmware: requesting ueagle-atm/CMVep.bin.v2 usb 2-2: [Ueagle-atm] requesting firmware ueagle-atm/CMVep.bin.v2 failed, try to get older cmvs firmware: requesting ueagle-atm/CMVep.bin usb 2-2: [Ueagle-atm] use deprecated cmvs version, please update your firmware usb 2-2: [ueagle-atm] modem started, waiting synchronization... scsi 5:0:0:0: Direct-Access Maxtor OneTouch 0125 PQ: 0 ANSI: 4 sd 5:0:0:0: [sdc] 976773168 512-byte hardware sectors (500108 MB) sd 5:0:0:0: [sdc] Write Protect is off sd 5:0:0:0: [sdc] Mode Sense: 2d 08 00 00 sd 5:0:0:0: [sdc] Assuming drive cache: write through sd 5:0:0:0: [sdc] 976773168 512-byte hardware sectors (500108 MB) sd 5:0:0:0: [sdc] Write Protect is off sd 5:0:0:0: [sdc] Mode Sense: 2d 08 00 00 sd 5:0:0:0: [sdc] Assuming drive cache: write through sdc: sd 5:0:0:0: [sdc] Attached SCSI disk sd 5:0:0:0: Attached scsi generic sg3 type 0 usb-storage: device scan complete PPP generic driver version 2.4.2 p4-clockmod: Unknown p4-clockmod-capable CPU. Please send an e-mail to p4-clockmod: Unknown p4-clockmod-capable CPU. Please send an e-mail to nf_conntrack version 0.5.0 (16384 buckets, 65536 max) Filesystem "dm-3": Disabling barriers, trial barrier write failed XFS mounting filesystem dm-3 scsi 6:0:0:0: Direct-Access Brother MFC-420CN 1.00 PQ: 0 ANSI: 2 sd 6:0:0:0: [sdd] Attached SCSI removable disk sd 6:0:0:0: Attached scsi generic sg4 type 0 usb-storage: device scan complete Ending clean XFS mount for filesystem: dm-3 EXT2-fs warning: mounting unchecked fs, running e2fsck is recommended Filesystem "dm-5": Disabling barriers, trial barrier write failed XFS mounting filesystem dm-5 Ending clean XFS mount for filesystem: dm-5 Filesystem "dm-1": Disabling barriers, trial barrier write failed XFS mounting filesystem dm-1 Ending clean XFS mount for filesystem: dm-1 Filesystem "dm-2": Disabling barriers, trial barrier write failed XFS mounting filesystem dm-2 Ending clean XFS mount for filesystem: dm-2 Adding 524280k swap on /dev/mapper/disks-swap. Priority:-1 extents:1 across:524280k usb 2-2: [ueagle-atm] modem operational ip_tables: (C) 2000-2006 Netfilter Core Team r8169: eth0: link up r8169: eth0: link up warning: `named' uses 32-bit capabilities (legacy support in use) NFSD: Using /var/lib/nfs/v4recovery as the NFSv4 state recovery directory NFSD: starting 90-second grace period mtrr: no MTRR for 40000000,8000000 found mtrr: no MTRR for 40000000,8000000 found mtrr: no MTRR for 40000000,8000000 found