Linux version 2.6.23 (root@bob) (gcc version 4.1.2) #1 SMP Mon Mar 24 01:34:59 CET 2008 BIOS-provided physical RAM map: BIOS-e820: 0000000000000000 - 000000000009f000 (usable) BIOS-e820: 000000000009f000 - 00000000000a0000 (reserved) BIOS-e820: 0000000000100000 - 000000003f6d3400 (usable) BIOS-e820: 000000003f6d3400 - 0000000040000000 (reserved) BIOS-e820: 00000000f0000000 - 00000000f4007000 (reserved) BIOS-e820: 00000000f4008000 - 00000000f400c000 (reserved) BIOS-e820: 00000000fec00000 - 00000000fec10000 (reserved) BIOS-e820: 00000000fed20000 - 00000000feda0000 (reserved) BIOS-e820: 00000000fee00000 - 00000000fee10000 (reserved) BIOS-e820: 00000000ffb00000 - 0000000100000000 (reserved) 118MB HIGHMEM available. 896MB LOWMEM available. Entering add_active_range(0, 0, 259795) 0 entries of 256 used Zone PFN ranges: DMA 0 -> 4096 Normal 4096 -> 229376 HighMem 229376 -> 259795 Movable zone start PFN for each node early_node_map[1] active PFN ranges 0: 0 -> 259795 On node 0 totalpages: 259795 DMA zone: 32 pages used for memmap DMA zone: 0 pages reserved DMA zone: 4064 pages, LIFO batch:0 Normal zone: 1760 pages used for memmap Normal zone: 223520 pages, LIFO batch:31 HighMem zone: 237 pages used for memmap HighMem zone: 30182 pages, LIFO batch:7 Movable zone: 0 pages used for memmap DMI 2.4 present. ACPI: RSDP 000FC1D0, 0014 (r0 DELL ) ACPI: RSDT 3F6D3A0F, 0040 (r1 DELL M07 27D7070A ASL 61) ACPI: FACP 3F6D4800, 0074 (r1 DELL M07 27D7070A ASL 61) ACPI: DSDT 3F6D5400, 438C (r1 INT430 SYSFexxx 1001 INTL 20050624) ACPI: FACS 3F6E3C00, 0040 ACPI: HPET 3F6D4F00, 0038 (r1 DELL M07 1 ASL 61) ACPI: APIC 3F6D5000, 0068 (r1 DELL M07 27D7070A ASL 47) ACPI: MCFG 3F6D4FC0, 003E (r16 DELL M07 27D7070A ASL 61) ACPI: SLIC 3F6D509C, 0176 (r1 DELL M07 27D7070A ASL 61) ACPI: BOOT 3F6D4BC0, 0028 (r1 DELL M07 27D7070A ASL 61) ACPI: SSDT 3F6D3A4F, 04DC (r1 PmRef CpuPm 3000 INTL 20050624) ACPI: PM-Timer IO Port: 0x1008 ACPI: Local APIC address 0xfee00000 ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled) Processor #0 6:14 APIC version 20 ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] enabled) Processor #1 6:14 APIC version 20 ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1]) ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1]) ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0]) IOAPIC[0]: apic_id 2, version 32, address 0xfec00000, GSI 0-23 ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl) ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level) ACPI: IRQ0 used by override. ACPI: IRQ2 used by override. ACPI: IRQ9 used by override. Enabling APIC mode: Flat. Using 1 I/O APICs ACPI: HPET id: 0x8086a201 base: 0xfed00000 Using ACPI (MADT) for SMP configuration information Allocating PCI resources starting at 50000000 (gap: 40000000:b0000000) swsusp: Registered nosave memory region: 000000000009f000 - 00000000000a0000 swsusp: Registered nosave memory region: 00000000000a0000 - 0000000000100000 Built 1 zonelists in Zone order. Total pages: 257766 Kernel command line: root=/dev/sda1 vga=791 videomode=intelfb:1024x768-16@60 hda=noprobe ide_setup: hda=noprobe mapped APIC to ffffb000 (fee00000) mapped IOAPIC to ffffa000 (fec00000) Enabling fast FPU save and restore... done. Enabling unmasked SIMD FPU exception support... done. Initializing CPU#0 PID hash table entries: 4096 (order: 12, 16384 bytes) Detected 1662.601 MHz processor. Console: colour dummy device 80x25 console [tty0] enabled Dentry cache hash table entries: 131072 (order: 7, 524288 bytes) Inode-cache hash table entries: 65536 (order: 6, 262144 bytes) Memory: 1019800k/1039180k available (6565k kernel code, 18764k reserved, 2151k data, 384k init, 121676k highmem) virtual kernel memory layout: fixmap : 0xffe14000 - 0xfffff000 (1964 kB) pkmap : 0xff800000 - 0xffc00000 (4096 kB) vmalloc : 0xf8800000 - 0xff7fe000 ( 111 MB) lowmem : 0xc0000000 - 0xf8000000 ( 896 MB) .init : 0xc098d000 - 0xc09ed000 ( 384 kB) .data : 0xc0769684 - 0xc098337c (2151 kB) .text : 0xc0100000 - 0xc0769684 (6565 kB) Checking if this processor honours the WP bit even in supervisor mode... Ok. Calibrating delay using timer specific routine.. 3328.03 BogoMIPS (lpj=1664016) Security Framework v1.0.0 initialized Mount-cache hash table entries: 512 CPU: After generic identify, caps: bfe9fbff 00100000 00000000 00000000 0000c189 00000000 00000000 00000000 monitor/mwait feature present. using mwait in idle threads. CPU: L1 I cache: 32K, L1 D cache: 32K CPU: L2 cache: 2048K CPU: Physical Processor ID: 0 CPU: Processor Core ID: 0 CPU: After all inits, caps: bfe9fbff 00100000 00000000 00002940 0000c189 00000000 00000000 00000000 Intel machine check architecture supported. Intel machine check reporting enabled on CPU#0. Compat vDSO mapped to ffffe000. Checking 'hlt' instruction... OK. SMP alternatives: switching to UP code ACPI: Core revision 20070126 CPU0: Intel Genuine Intel(R) CPU T2300 @ 1.66GHz stepping 08 SMP alternatives: switching to SMP code Booting processor 1/1 eip 3000 Initializing CPU#1 Calibrating delay using timer specific routine.. 3325.04 BogoMIPS (lpj=1662523) CPU: After generic identify, caps: bfe9fbff 00100000 00000000 00000000 0000c189 00000000 00000000 00000000 monitor/mwait feature present. CPU: L1 I cache: 32K, L1 D cache: 32K CPU: L2 cache: 2048K CPU: Physical Processor ID: 0 CPU: Processor Core ID: 1 CPU: After all inits, caps: bfe9fbff 00100000 00000000 00002940 0000c189 00000000 00000000 00000000 Intel machine check architecture supported. Intel machine check reporting enabled on CPU#1. CPU1: Intel Genuine Intel(R) CPU T2300 @ 1.66GHz stepping 08 Total of 2 processors activated (6653.07 BogoMIPS). ENABLING IO-APIC IRQs ..TIMER: vector=0x31 apic1=0 pin1=2 apic2=-1 pin2=-1 checking TSC synchronization [CPU#0 -> CPU#1]: Measured 3093193800 cycles TSC warp between CPUs, turning off TSC clock. Marking TSC unstable due to: check_tsc_sync_source failed. Brought up 2 CPUs xor: automatically using best checksumming function: pIII_sse pIII_sse : 4352.000 MB/sec xor: using function: pIII_sse (4352.000 MB/sec) NET: Registered protocol family 16 No dock devices found. ACPI: bus type pci registered PCI: Using MMCONFIG Setting up standard PCI resources ACPI: EC: Look up EC in DSDT ACPI: Interpreter enabled ACPI: (supports S0 S3 S4 S5) ACPI: Using IOAPIC for interrupt routing ACPI: PCI Root Bridge [PCI0] (0000:00) PCI quirk: region 1000-107f claimed by ICH6 ACPI/GPIO/TCO PCI quirk: region 1080-10bf claimed by ICH6 GPIO PCI: Transparent bridge - 0000:00:1e.0 ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCIE._PRT] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.RP01._PRT] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.RP02._PRT] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.RP04._PRT] ACPI: PCI Interrupt Link [LNKA] (IRQs 9 10 *11) ACPI: PCI Interrupt Link [LNKB] (IRQs 5 7) *4 ACPI: PCI Interrupt Link [LNKC] (IRQs 9 10 *11) ACPI: PCI Interrupt Link [LNKD] (IRQs 5 7 9 10 11) *3 ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 *9 10 11 12 14 15) ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 9 *10 11 12 14 15) ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 *7 9 10 11 12 14 15) ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 *5 6 7 9 10 11 12 14 15) Linux Plug and Play Support v0.97 (c) Adam Belay pnp: PnP ACPI init ACPI: bus type pnp registered pnp: PnP ACPI: found 12 devices ACPI: ACPI bus type pnp unregistered SCSI subsystem initialized libata version 2.21 loaded. usbcore: registered new interface driver usbfs usbcore: registered new interface driver hub usbcore: registered new device driver usb PCI: Using ACPI for IRQ routing PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report ACPI: RTC can wake from S4 Time: hpet clocksource has been installed. Switched to high resolution mode on CPU 0 Switched to high resolution mode on CPU 1 pnp: 00:00: iomem range 0x0-0x9fbff could not be reserved pnp: 00:00: iomem range 0x9fc00-0x9ffff could not be reserved pnp: 00:00: iomem range 0xc0000-0xcffff could not be reserved pnp: 00:00: iomem range 0xe0000-0xfffff could not be reserved pnp: 00:02: ioport range 0x4d0-0x4d1 has been reserved pnp: 00:02: ioport range 0x1000-0x1005 has been reserved pnp: 00:02: ioport range 0x1008-0x100f has been reserved pnp: 00:03: ioport range 0xf400-0xf4fe has been reserved pnp: 00:03: ioport range 0x1006-0x1007 has been reserved pnp: 00:03: ioport range 0x100a-0x1059 could not be reserved pnp: 00:03: ioport range 0x1060-0x107f has been reserved pnp: 00:03: ioport range 0x1080-0x10bf has been reserved pnp: 00:03: ioport range 0x10c0-0x10df has been reserved pnp: 00:08: ioport range 0xc80-0xcff could not be reserved pnp: 00:08: ioport range 0x910-0x91f has been reserved pnp: 00:08: ioport range 0x920-0x92f has been reserved pnp: 00:08: ioport range 0xcb0-0xcbf has been reserved pnp: 00:08: ioport range 0x930-0x97f has been reserved pnp: 00:0b: iomem range 0xfed00000-0xfed003ff has been reserved PCI: Bridge: 0000:00:1c.0 IO window: disabled. MEM window: disabled. PREFETCH window: disabled. PCI: Bridge: 0000:00:1c.1 IO window: disabled. MEM window: efd00000-efdfffff PREFETCH window: disabled. PCI: Bridge: 0000:00:1c.3 IO window: d000-dfff MEM window: efa00000-efcfffff PREFETCH window: e0000000-e01fffff PCI: Bridge: 0000:00:1e.0 IO window: disabled. MEM window: ef900000-ef9fffff PREFETCH window: disabled. ACPI: PCI Interrupt 0000:00:1c.0[A] -> GSI 16 (level, low) -> IRQ 16 PCI: Setting latency timer of device 0000:00:1c.0 to 64 ACPI: PCI Interrupt 0000:00:1c.1[B] -> GSI 17 (level, low) -> IRQ 17 PCI: Setting latency timer of device 0000:00:1c.1 to 64 ACPI: PCI Interrupt 0000:00:1c.3[D] -> GSI 19 (level, low) -> IRQ 18 PCI: Setting latency timer of device 0000:00:1c.3 to 64 PCI: Setting latency timer of device 0000:00:1e.0 to 64 NET: Registered protocol family 2 IP route cache hash table entries: 32768 (order: 5, 131072 bytes) TCP established hash table entries: 131072 (order: 8, 1572864 bytes) TCP bind hash table entries: 65536 (order: 7, 524288 bytes) TCP: Hash tables configured (established 131072 bind 65536) TCP reno registered Simple Boot Flag at 0x79 set to 0x1 apm: BIOS not found. highmem bounce pool size: 64 pages VFS: Disk quotas dquot_6.5.1 Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) NTFS driver 2.1.28 [Flags: R/W]. JFS: nTxBlock = 7968, nTxLock = 63751 SGI XFS with ACLs, security attributes, large block numbers, no debug enabled SGI XFS Quota Management subsystem OCFS2 1.3.3 OCFS2 Node Manager 1.3.3 OCFS2 DLM 1.3.3 OCFS2 DLMFS 1.3.3 OCFS2 User DLM kernel interface loaded GFS2 (built Mar 24 2008 00:54:30) installed async_tx: api initialized (async) io scheduler noop registered io scheduler anticipatory registered io scheduler deadline registered io scheduler cfq registered (default) Boot video device is 0000:00:02.0 PCI: Setting latency timer of device 0000:00:1c.0 to 64 assign_interrupt_mode Found MSI capability Allocate Port Service[0000:00:1c.0:pcie00] Allocate Port Service[0000:00:1c.0:pcie02] Allocate Port Service[0000:00:1c.0:pcie03] PCI: Setting latency timer of device 0000:00:1c.1 to 64 assign_interrupt_mode Found MSI capability Allocate Port Service[0000:00:1c.1:pcie00] Allocate Port Service[0000:00:1c.1:pcie02] Allocate Port Service[0000:00:1c.1:pcie03] PCI: Setting latency timer of device 0000:00:1c.3 to 64 assign_interrupt_mode Found MSI capability Allocate Port Service[0000:00:1c.3:pcie00] Allocate Port Service[0000:00:1c.3:pcie02] Allocate Port Service[0000:00:1c.3:pcie03] pci_hotplug: PCI Hot Plug PCI Core version: 0.5 vesafb: framebuffer at 0xd0000000, mapped to 0xf8d00000, using 3072k, total 7872k vesafb: mode is 1024x768x16, linelength=2048, pages=4 vesafb: scrolling: redraw vesafb: Truecolor: size=0:5:6:5, shift=0:11:5:0 Console: switching to colour frame buffer device 128x48 fb0: VESA VGA frame buffer device ACPI: AC Adapter [AC] (on-line) ACPI: Battery Slot [BAT0] (battery present) input: Lid Switch as /devices/virtual/input/input0 ACPI: Lid Switch [LID] input: Power Button (CM) as /devices/virtual/input/input1 ACPI: Power Button (CM) [PBTN] input: Sleep Button (CM) as /devices/virtual/input/input2 ACPI: Sleep Button (CM) [SBTN] ACPI: SSDT 3F6D4176, 0202 (r1 PmRef Cpu0Ist 3000 INTL 20050624) ACPI: SSDT 3F6D3F2B, 01C6 (r1 PmRef Cpu0Cst 3001 INTL 20050624) ACPI: CPU0 (power states: C1[C1] C2[C2] C3[C3]) ACPI: Processor [CPU0] (supports 8 throttling states) ACPI: SSDT 3F6D4378, 00C4 (r1 PmRef Cpu1Ist 3000 INTL 20050624) ACPI: SSDT 3F6D40F1, 0085 (r1 PmRef Cpu1Cst 3000 INTL 20050624) ACPI: CPU1 (power states: C1[C1] C2[C2] C3[C3]) ACPI: Processor [CPU1] (supports 8 throttling states) ACPI: Thermal Zone [THM] (40 C) isapnp: Scanning for PnP cards... isapnp: No Plug & Play device found Real Time Clock Driver v1.12ac Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled Floppy drive(s): fd0 is 1.44M Clocksource tsc unstable (delta = -275976216 ns) floppy0: no floppy controllers found RAMDISK driver initialized: 16 RAM disks of 16384K size 1024 blocksize loop: module loaded Compaq SMART2 Driver (v 2.6.0) HP CISS Driver (v 3.6.14) input: Macintosh mouse button emulation as /devices/virtual/input/input3 Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2 ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx Probing IDE interface ide0... hdb: IRQ probe failed (0xfffffcfe) hdb: IRQ probe failed (0xfffffcfe) Probing IDE interface ide1... hdc: TSSTcorp DVD+/-RW TS-L532B, ATAPI CD/DVD-ROM drive Probing IDE interface ide2... Probing IDE interface ide3... Probing IDE interface ide4... Probing IDE interface ide5... ide1 at 0x170-0x177,0x376 on irq 15 hdc: ATAPI 24X DVD-ROM DVD-R CD-R/RW drive, 2048kB Cache Uniform CD-ROM driver Revision: 3.20 ide-floppy driver 0.99.newide Loading iSCSI transport class v2.0-724. iscsi: registered transport (tcp) Loading Adaptec I2O RAID: Version 2.4 Build 5go Detecting Adaptec I2O RAID controllers... Adaptec aacraid driver 1.1-5[2449]-ms aic94xx: Adaptec aic94xx SAS/SATA driver version 1.0.3 loaded scsi: Detection failed (no card) sym53c416.c: Version 1.0.0-ac qlogicfas: no cards were found, please specify I/O address and IRQ using iobase= and irq= options<6>QLogic Fibre Channel HBA Driver iscsi: registered transport (qla4xxx) QLogic iSCSI HBA Driver Emulex LightPulse Fibre Channel SCSI driver 8.2.2 Copyright(c) 2004-2007 Emulex. All rights reserved. seagate: ST0x/TMC-8xx not detected. Failed initialization of WD-7000 SCSI card! DC390: clustering now enabled by default. If you get problems load with "disable_clustering=1" and report to maintainers megaraid cmm: 2.20.2.7 (Release Date: Sun Jul 16 00:01:03 EST 2006) megaraid: 2.20.5.1 (Release Date: Thu Nov 16 15:32:35 EST 2006) megasas: 00.00.03.10-rc5 Thu May 17 10:09:32 PDT 2007 GDT-HA: Storage RAID Controller Driver. Version: 3.05 GDT-HA: Found 0 PCI Storage RAID Controllers 3ware Storage Controller device driver for Linux v1.26.02.002. 3ware 9000 Storage Controller device driver for Linux v2.26.02.010. nsp32: loading... ipr: IBM Power RAID SCSI Device Driver version: 2.4.1 (April 24, 2007) RocketRAID 3xxx SATA Controller driver v1.0 (060426) st: Version 20070203, fixed bufsize 32768, s/g segs 256 ata_piix 0000:00:1f.2: version 2.12 ata_piix 0000:00:1f.2: MAP [ P0 P2 IDE IDE ] ACPI: PCI Interrupt 0000:00:1f.2[B] -> GSI 17 (level, low) -> IRQ 17 PCI: Unable to reserve I/O region #3:8@170 for device 0000:00:1f.2 ata_piix 0000:00:1f.2: failed to request/iomap BARs for port 1 (errno=-16) PCI: Setting latency timer of device 0000:00:1f.2 to 64 scsi2 : ata_piix scsi3 : ata_piix ata1: SATA max UDMA/133 cmd 0x000101f0 ctl 0x000103f6 bmdma 0x0001bfa0 irq 14 ata2: DUMMY ata1.00: Host Protected Area detected: current size: 192426570 sectors native size: 195371568 sectors ata1.00: ATA-6: TOSHIBA MK1032GSX, AS022D, max UDMA/100 ata1.00: 192426570 sectors, multi 8: LBA48 NCQ (depth 0/32) ata1.00: Host Protected Area detected: current size: 192426570 sectors native size: 195371568 sectors ata1.00: configured for UDMA/100 scsi 2:0:0:0: Direct-Access ATA TOSHIBA MK1032GS AS02 PQ: 0 ANSI: 5 sd 2:0:0:0: [sda] 192426570 512-byte hardware sectors (98522 MB) sd 2:0:0:0: [sda] Write Protect is off sd 2:0:0:0: [sda] Mode Sense: 00 3a 00 00 sd 2:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA sd 2:0:0:0: [sda] 192426570 512-byte hardware sectors (98522 MB) sd 2:0:0:0: [sda] Write Protect is off sd 2:0:0:0: [sda] Mode Sense: 00 3a 00 00 sd 2:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA sda: sda1 sda2 sda3 sda4 < sda5 sda6 > sda2: sda3: sd 2:0:0:0: [sda] Attached SCSI disk I2O subsystem v1.325 i2o: max drivers = 8 I2O Configuration OSM v1.323 I2O Bus Adapter OSM v1.317 I2O Block Device OSM v1.325 I2O SCSI Peripheral OSM v1.316 I2O ProcFS OSM v1.316 Fusion MPT base driver 3.04.05 Copyright (c) 1999-2007 LSI Logic Corporation Fusion MPT SPI Host driver 3.04.05 Fusion MPT FC Host driver 3.04.05 Fusion MPT SAS Host driver 3.04.05 ACPI: PCI Interrupt 0000:02:01.0[A] -> GSI 19 (level, low) -> IRQ 18 ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[18] MMIO=[ef9fd800-ef9fdfff] Max Packet=[2048] IR/IT contexts=[4/4] usbmon: debugfs is not available ACPI: PCI Interrupt 0000:00:1d.7[A] -> GSI 20 (level, low) -> IRQ 19 PCI: Setting latency timer of device 0000:00:1d.7 to 64 ehci_hcd 0000:00:1d.7: EHCI Host Controller ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 1 ehci_hcd 0000:00:1d.7: debug port 1 PCI: cache line size of 32 is not supported by device 0000:00:1d.7 ehci_hcd 0000:00:1d.7: irq 19, io mem 0xffa80000 ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004 usb usb1: configuration #1 chosen from 1 choice hub 1-0:1.0: USB hub found hub 1-0:1.0: 8 ports detected 116x: driver isp116x-hcd, 03 Nov 2005 ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver USB Universal Host Controller Interface driver v3.0 ACPI: PCI Interrupt 0000:00:1d.0[A] -> GSI 20 (level, low) -> IRQ 19 PCI: Setting latency timer of device 0000:00:1d.0 to 64 uhci_hcd 0000:00:1d.0: UHCI Host Controller uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 2 uhci_hcd 0000:00:1d.0: irq 19, io base 0x0000bf80 usb usb2: configuration #1 chosen from 1 choice hub 2-0:1.0: USB hub found hub 2-0:1.0: 2 ports detected ACPI: PCI Interrupt 0000:00:1d.1[B] -> GSI 21 (level, low) -> IRQ 20 PCI: Setting latency timer of device 0000:00:1d.1 to 64 uhci_hcd 0000:00:1d.1: UHCI Host Controller uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 3 uhci_hcd 0000:00:1d.1: irq 20, io base 0x0000bf60 usb usb3: configuration #1 chosen from 1 choice hub 3-0:1.0: USB hub found hub 3-0:1.0: 2 ports detected ACPI: PCI Interrupt 0000:00:1d.2[C] -> GSI 22 (level, low) -> IRQ 21 PCI: Setting latency timer of device 0000:00:1d.2 to 64 uhci_hcd 0000:00:1d.2: UHCI Host Controller uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 4 uhci_hcd 0000:00:1d.2: irq 21, io base 0x0000bf40 usb usb4: configuration #1 chosen from 1 choice hub 4-0:1.0: USB hub found hub 4-0:1.0: 2 ports detected ACPI: PCI Interrupt 0000:00:1d.3[D] -> GSI 23 (level, low) -> IRQ 22 PCI: Setting latency timer of device 0000:00:1d.3 to 64 uhci_hcd 0000:00:1d.3: UHCI Host Controller uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 5 uhci_hcd 0000:00:1d.3: irq 22, io base 0x0000bf20 usb usb5: configuration #1 chosen from 1 choice hub 5-0:1.0: USB hub found hub 5-0:1.0: 2 ports detected sl811: driver sl811-hcd, 19 May 2005 Initializing USB Mass Storage driver... usb 4-2: new full speed USB device using uhci_hcd and address 2 usb 4-2: configuration #1 chosen from 1 choice usbcore: registered new interface driver usb-storage USB Mass Storage support registered. PNP: PS/2 Controller [PNP0303:KBC,PNP0f13:PS2M] at 0x60,0x64 irq 1,12 serio: i8042 KBD port at 0x60,0x64 irq 1 serio: i8042 AUX port at 0x60,0x64 irq 12 mice: PS/2 mouse device common for all mice input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input4 md: linear personality registered for level -1 md: raid0 personality registered for level 0 md: raid1 personality registered for level 1 md: raid10 personality registered for level 10 raid6: int32x1 531 MB/s raid6: int32x2 605 MB/s raid6: int32x4 488 MB/s raid6: int32x8 449 MB/s raid6: mmxx1 1507 MB/s raid6: mmxx2 1695 MB/s raid6: sse1x1 1136 MB/s raid6: sse1x2 1566 MB/s raid6: sse2x1 1777 MB/s raid6: sse2x2 2011 MB/s raid6: using algorithm sse2x2 (2011 MB/s) md: raid6 personality registered for level 6 ieee1394: Host added: ID:BUS[0-00:1023] GUID[4a4fc000087ba850] md: raid5 personality registered for level 5 md: raid4 personality registered for level 4 md: multipath personality registered for level -4 device-mapper: ioctl: 4.11.0-ioctl (2006-10-12) initialised: dm-devel@redhat.com usbcore: registered new interface driver hiddev input: Logitech USB Gaming Mouse as /devices/pci0000:00/0000:00:1d.2/usb4/4-2/4-2:1.0/input/input5 input: USB HID v1.11 Mouse [Logitech USB Gaming Mouse] on usb-0000:00:1d.2-2 hiddev96: USB HID v1.11 Device [Logitech USB Gaming Mouse] on usb-0000:00:1d.2-2 usbcore: registered new interface driver usbhid drivers/hid/usbhid/hid-core.c: v2.6:USB HID core driver TCP cubic registered Initializing XFRM netlink socket NET: Registered protocol family 1 NET: Registered protocol family 17 Using IPI No-Shortcut mode Synaptics Touchpad, model: 1, fw: 6.2, id: 0x180b1, caps: 0xa04713/0x200000 input: SynPS/2 Synaptics TouchPad as /devices/platform/i8042/serio1/input/input6 md: Autodetecting RAID arrays. md: autorun ... md: ... autorun DONE. kjournald starting. Commit interval 5 seconds EXT3-fs: mounted filesystem with ordered data mode. VFS: Mounted root (ext3 filesystem) readonly. Freeing unused kernel memory: 384k freed sd 2:0:0:0: Attached scsi generic sg0 type 0 shpchp: Standard Hot Plug PCI Controller Driver version: 0.4 iTCO_vendor_support: vendor-support=0 iTCO_wdt: Intel TCO WatchDog Timer Driver v1.02 (26-Jul-2007) iTCO_wdt: Found a ICH7-M TCO device (Version=2, TCOBASE=0x1060) iTCO_wdt: initialized. heartbeat=30 sec (nowayout=0) Linux agpgart interface v0.102 agpgart: Detected an Intel 945GM Chipset. agpgart: Detected 7932K stolen memory. intel_rng: FWH not detected ieee80211_crypt: registered algorithm 'NULL' ieee80211: 802.11 data/management/control stack, git-1.1.13 ieee80211: Copyright (C) 2004-2005 Intel Corporation sdhci: Secure Digital Host Controller Interface driver sdhci: Copyright(c) Pierre Ossman agpgart: AGP aperture is 256M @ 0xd0000000 b44.c:v1.01 (Jun 16, 2006) ACPI: PCI Interrupt 0000:02:00.0[A] -> GSI 17 (level, low) -> IRQ 17 eth0: Broadcom 4400 10/100BaseT Ethernet 00:15:c5:7d:bf:ae sdhci: SDHCI controller found at 0000:02:01.1 [1180:0822] (rev 19) ACPI: PCI Interrupt 0000:02:01.1[B] -> GSI 18 (level, low) -> IRQ 23 mmc0: SDHCI at 0xef9fd400 irq 23 DMA ACPI: PCI Interrupt 0000:00:1f.3[B] -> GSI 17 (level, low) -> IRQ 17 input: Video Bus as /devices/virtual/input/input7 ACPI: Video Device [VID] (multi-head: yes rom: no post: no) input: Video Bus as /devices/virtual/input/input8 ACPI: Video Device [VID2] (multi-head: yes rom: no post: no) EXT3 FS on sda1, internal journal Intel ISA PCIC probe: not found. Databook TCIC-2 PCMCIA probe: not found. b44: eth0: Link is up at 100 Mbps, full duplex. b44: eth0: Flow control is off for TX and off for RX. ACPI: PCI Interrupt 0000:00:1b.0[A] -> GSI 21 (level, low) -> IRQ 20 usbcore: registered new interface driver ossusb [drm] Initialized drm 1.1.0 20060810 ACPI: PCI Interrupt 0000:00:02.0[A] -> GSI 16 (level, low) -> IRQ 16 [drm] Initialized i915 1.6.0 20060119 on minor 0 NET: Registered protocol family 10 lo: Disabled Privacy Extensions eth0: no IPv6 routers present