0000:02:09.3: PME# disabled
pci 0000:00:1e.0: transparent bridge
pci 0000:00:1e.0: bridge 32bit mmio: [0xb8000000-0xb80fffff]
bus 00 -> node 0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.RP01._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCIB._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs *11)
ACPI: PCI Interrupt Link [LNKB] (IRQs *10)
ACPI: PCI Interrupt Link [LNKC] (IRQs *5)
ACPI: PCI Interrupt Link [LNKD] (IRQs *5)
ACPI: PCI Interrupt Link [LNKE] (IRQs *11)
ACPI: PCI Interrupt Link [LNKF] (IRQs 10) *0, disabled.
ACPI: PCI Interrupt Link [LNKG] (IRQs *5)
ACPI: PCI Interrupt Link [LNKH] (IRQs *5)
ACPI: Power Resource [CFAN] (on)
SCSI subsystem initialized
libata version 3.00 loaded.
PCI: Using ACPI for IRQ routing
hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0
hpet0: 3 comparators, 64-bit 14.318180 MHz counter
pnp: PnP ACPI init
ACPI: bus type pnp registered
pnp: PnP ACPI: found 10 devices
ACPI: ACPI bus type pnp unregistered
system 00:01: iomem range 0xe0000000-0xefffffff has been reserved
system 00:01: iomem range 0xf0000000-0xf0003fff has been reserved
system 00:01: iomem range 0xf0004000-0xf0004fff has been reserved
system 00:01: iomem range 0xf0005000-0xf0005fff has been reserved
system 00:01: iomem range 0xf0008000-0xf000bfff has been reserved
system 00:01: iomem range 0xfed20000-0xfed8ffff has been reserved
system 00:06: ioport range 0x680-0x6df has been reserved
system 00:06: ioport range 0x6f0-0x6ff has been reserved
system 00:06: ioport range 0x800-0x80f has been reserved
system 00:06: ioport range 0x900-0x90f has been reserved
system 00:06: ioport range 0x1000-0x107f has been reserved
system 00:06: ioport range 0x1180-0x11bf has been reserved
system 00:06: ioport range 0x1640-0x164f has been reserved
pci 0000:00:1c.0: PCI bridge, secondary bus 0000:01
pci 0000:00:1c.0:   IO window: 0x3000-0x3fff
pci 0000:00:1c.0:   MEM window: 0xb4000000-0xb7ffffff
pci 0000:00:1c.0:   PREFETCH window: 0x000000d0000000-0x000000d3ffffff
pci 0000:02:09.0: CardBus bridge, secondary bus 0000:03
pci 0000:02:09.0:   IO window: 0x004000-0x0040ff
pci 0000:02:09.0:   IO window: 0x004400-0x0044ff
pci 0000:02:09.0:   PREFETCH window: 0x88000000-0x8bffffff
pci 0000:02:09.0:   MEM window: 0x90000000-0x93ffffff
pci 0000:00:1e.0: PCI bridge, secondary bus 0000:02
pci 0000:00:1e.0:   IO window: 0x4000-0x4fff
pci 0000:00:1e.0:   MEM window: 0xb8000000-0xb80fffff
pci 0000:00:1e.0:   PREFETCH window: 0x00000088000000-0x0000008dffffff
pci 0000:00:1c.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17
pci 0000:00:1c.0: setting latency timer to 64
pci 0000:00:1e.0: setting latency timer to 64
pci 0000:02:09.0: power state changed by ACPI to D0
pci 0000:02:09.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
bus: 00 index 0 io port: [0x00-0xffff]
bus: 00 index 1 mmio: [0x000000-0xffffffffffffffff]
bus: 01 index 0 io port: [0x3000-0x3fff]
bus: 01 index 1 mmio: [0xb4000000-0xb7ffffff]
bus: 01 index 2 mmio: [0xd0000000-0xd3ffffff]
bus: 01 index 3 mmio: [0x0-0x0]
bus: 02 index 0 io port: [0x4000-0x4fff]
bus: 02 index 1 mmio: [0xb8000000-0xb80fffff]
bus: 02 index 2 mmio: [0x88000000-0x8dffffff]
bus: 02 index 3 io port: [0x00-0xffff]
bus: 02 index 4 mmio: [0x000000-0xffffffffffffffff]
bus: 03 index 0 io port: [0x4000-0x40ff]
bus: 03 index 1 io port: [0x4400-0x44ff]
bus: 03 index 2 mmio: [0x88000000-0x8bffffff]
bus: 03 index 3 mmio: [0x90000000-0x93ffffff]
NET: Registered protocol family 2
IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
TCP bind hash table entries: 65536 (order: 6, 262144 bytes)
TCP: Hash tables configured (established 131072 bind 65536)
TCP reno registered
NET: Registered protocol family 1
Simple Boot Flag at 0x36 set to 0x1
Machine check exception polling timer started.
highmem bounce pool size: 64 pages
msgmni has been set to 1738
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered (default)
pci 0000:00:02.0: Boot video device
uvesafb: Intel Corporation, Intel(r)915GM/910ML/915MS Graphics Controller, Hardware Version 0.0, OEM: Intel(r)915GM/910ML/915MS Graphics Chip Accelerated VGA BIOS, VBE v3.0
uvesafb: VBIOS/hardware doesn't support DDC transfers
uvesafb: no monitor limits have been set, default refresh rate will be used
uvesafb: scrolling: redraw
Console: switching to colour frame buffer device 128x48
uvesafb: framebuffer at 0xc0000000, mapped to 0xf8280000, using 7872k, total 7872k
fb0: VESA VGA frame buffer device
ACPI: AC Adapter [ADP1] (on-line)
ACPI: Battery Slot [BAT1] (battery present)
input: Power Button (FF) as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input0
ACPI: Power Button (FF) [PWRF]
input: Lid Switch as /devices/LNXSYSTM:00/device:00/PNP0C0D:00/input/input1
ACPI: Lid Switch [LID0]
input: Power Button (CM) as /devices/LNXSYSTM:00/device:00/PNP0C0C:00/input/input2
ACPI: Power Button (CM) [PWRB]
input: Sleep Button (CM) as /devices/LNXSYSTM:00/device:00/PNP0C0E:00/input/input3
ACPI: Sleep Button (CM) [SLPB]
fan PNP0C0B:00: registered as cooling_device0
ACPI: Fan [FAN1] (on)
ACPI: CPU0 (power states: C1[C1] C2[C2] C3[C3])
processor ACPI_CPU:00: registered as cooling_device1
ACPI: Processor [CPU0] (supports 2 throttling states)
thermal LNXTHERM:01: registered as thermal_zone0
ACPI: Thermal Zone [THRM] (51 C)
Driver 'sd' needs updating - please use bus_type methods
ata_piix 0000:00:1f.1: version 2.12
ata_piix 0000:00:1f.1: PCI INT A -> GSI 18 (level, low) -> IRQ 18
ata_piix 0000:00:1f.1: setting latency timer to 64
scsi0 : ata_piix
scsi1 : ata_piix
ata1: PATA max UDMA/100 cmd 0x1f0 ctl 0x3f6 bmdma 0x1810 irq 14
ata2: PATA max UDMA/100 cmd 0x170 ctl 0x376 bmdma 0x1818 irq 15
Switched to high resolution mode on CPU 0
ata1.00: HPA detected: current 155490289, native 156301488
ata1.00: ATA-6: FUJITSU MHV2080AH, 00420097, max UDMA/100
ata1.00: 155490289 sectors, multi 16: LBA 
ata1.01: ATAPI: TSSTcorpCD/DVDW TS-L632B, TM32, max UDMA/33
ata1.00: configured for UDMA/100
ata1.01: configured for UDMA/33
ata2: port disabled. ignoring.
scsi 0:0:0:0: Direct-Access     ATA      FUJITSU MHV2080A 0042 PQ: 0 ANSI: 5
sd 0:0:0:0: [sda] 155490289 512-byte hardware sectors: (79.6 GB/74.1 GiB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 0:0:0:0: [sda] 155490289 512-byte hardware sectors: (79.6 GB/74.1 GiB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
 sda: sda1 sda2 sda3 < sda5 sda6 >
sd 0:0:0:0: [sda] Attached SCSI disk
scsi 0:0:1:0: CD-ROM            TSSTcorp CD/DVDW TS-L632B TM32 PQ: 0 ANSI: 5
PNP: PS/2 Controller [PNP0303:PS2K,PNP0f13:PS2M] at 0x60,0x64 irq 1,12
i8042.c: Detected active multiplexing controller, rev 1.1.
serio: i8042 KBD port at 0x60,0x64 irq 1
serio: i8042 AUX0 port at 0x60,0x64 irq 12
serio: i8042 AUX1 port at 0x60,0x64 irq 12
serio: i8042 AUX2 port at 0x60,0x64 irq 12
serio: i8042 AUX3 port at 0x60,0x64 irq 12
mice: PS/2 mouse device common for all mice
cpuidle: using governor ladder
cpuidle: using governor menu
TCP cubic registered
NET: Registered protocol family 17
Using IPI Shortcut mode
Marking TSC unstable due to TSC halts in idle
input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input4
Clocksource tsc unstable (delta = -231761099 ns)
EXT3-fs: sda2: couldn't mount because of unsupported optional features (40).
EXT4-fs: barriers enabled
EXT4-fs: delayed allocation enabled
EXT4-fs: file extents enabled
EXT4-fs: mballoc enabled
EXT4-fs: mounted filesystem with ordered data mode.
VFS: Mounted root (ext4 filesystem) readonly.
Freeing unused kernel memory: 316k freed
kjournald2 starting.  Commit interval 5 seconds
Real Time Clock Driver v1.12ac
sd 0:0:0:0: Attached scsi generic sg0 type 0
scsi 0:0:1:0: Attached scsi generic sg1 type 5
ieee80211_crypt: registered algorithm 'NULL'
Driver 'sr' needs updating - please use bus_type methods
ieee80211: 802.11 data/management/control stack, git-1.1.13
ieee80211: Copyright (C) 2004-2005 Intel Corporation <jketreno@linux.intel.com>
Linux agpgart interface v0.103
sr0: scsi3-mmc drive: 24x/24x writer dvd-ram cd/rw xa/form2 cdda tray
Uniform CD-ROM driver Revision: 3.20
sr 0:0:1:0: Attached scsi CD-ROM sr0
i801_smbus 0000:00:1f.3: PCI INT B -> GSI 19 (level, low) -> IRQ 19
ACPI: I/O resource 0000:00:1f.3 [0x18a0-0x18bf] conflicts with ACPI region SMBI [0x18a0-0x18af]
ACPI: Device needs an ACPI driver
ohci1394 0000:02:09.1: power state changed by ACPI to D0
ohci1394 0000:02:09.1: PCI INT B -> GSI 17 (level, low) -> IRQ 17
agpgart-intel 0000:00:00.0: Intel 915GM Chipset
agpgart-intel 0000:00:00.0: detected 7932K stolen memory
agpgart-intel 0000:00:00.0: AGP aperture is 256M @ 0xc0000000
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
uhci_hcd: USB Universal Host Controller Interface driver
uhci_hcd 0000:00:1d.0: PCI INT A -> GSI 23 (level, low) -> IRQ 23
uhci_hcd 0000:00:1d.0: setting latency timer to 64
uhci_hcd 0000:00:1d.0: UHCI Host Controller
uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 1
uhci_hcd 0000:00:1d.0: irq 23, io base 0x00001820
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
uhci_hcd 0000:00:1d.1: PCI INT B -> GSI 19 (level, low) -> IRQ 19
uhci_hcd 0000:00:1d.1: setting latency timer to 64
uhci_hcd 0000:00:1d.1: UHCI Host Controller
uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 2
uhci_hcd 0000:00:1d.1: irq 19, io base 0x00001840
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
uhci_hcd 0000:00:1d.2: PCI INT C -> GSI 18 (level, low) -> IRQ 18
uhci_hcd 0000:00:1d.2: setting latency timer to 64
uhci_hcd 0000:00:1d.2: UHCI Host Controller
uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 3
uhci_hcd 0000:00:1d.2: irq 18, io base 0x00001860
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
uhci_hcd 0000:00:1d.3: PCI INT D -> GSI 16 (level, low) -> IRQ 16
uhci_hcd 0000:00:1d.3: setting latency timer to 64
uhci_hcd 0000:00:1d.3: UHCI Host Controller
uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 4
uhci_hcd 0000:00:1d.3: irq 16, io base 0x00001880
usb usb4: configuration #1 chosen from 1 choice
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
ipw2200: Intel(R) PRO/Wireless 2200/2915 Network Driver, 1.2.2kmprq
ipw2200: Copyright(c) 2003-2006 Intel Corporation
ohci1394: fw-host0: OHCI-1394 1.0 (PCI): IRQ=[17]  MMIO=[b8003000-b80037ff]  Max Packet=[2048]  IR/IT contexts=[4/4]
yenta_cardbus 0000:02:09.0: CardBus bridge found [144d:c01a]
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
Warning! ehci_hcd should always be loaded before uhci_hcd and ohci_hcd, not after
ehci_hcd 0000:00:1d.7: PCI INT A -> GSI 23 (level, low) -> IRQ 23
ehci_hcd 0000:00:1d.7: setting latency timer to 64
ehci_hcd 0000:00:1d.7: EHCI Host Controller
ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 5
ehci_hcd 0000:00:1d.7: debug port 1
ehci_hcd 0000:00:1d.7: cache line size of 32 is not supported
ehci_hcd 0000:00:1d.7: irq 23, io mem 0xb0040000
sdhci: Secure Digital Host Controller Interface driver
sdhci: Copyright(c) Pierre Ossman
ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00
usb usb5: configuration #1 chosen from 1 choice
hub 5-0:1.0: USB hub found
hub 5-0:1.0: 8 ports detected
yenta_cardbus 0000:02:09.0: ISA IRQ mask 0x0cb8, PCI irq 16
yenta_cardbus 0000:02:09.0: Socket status: 30000006
yenta_cardbus 0000:02:09.0: pcmcia: parent PCI bridge I/O window: 0x4000 - 0x4fff
yenta_cardbus 0000:02:09.0: pcmcia: parent PCI bridge Memory window: 0xb8000000 - 0xb80fffff
yenta_cardbus 0000:02:09.0: pcmcia: parent PCI bridge Memory window: 0x88000000 - 0x8dffffff
b44 0000:02:05.0: PCI INT A -> GSI 22 (level, low) -> IRQ 22
ssb: Sonics Silicon Backplane found on PCI device 0000:02:05.0
b44.c:v2.0
ipw2200 0000:02:07.0: PCI INT A -> GSI 20 (level, low) -> IRQ 20
ipw2200: Detected Intel PRO/Wireless 2200BG Network Connection
ipw2200 0000:02:07.0: firmware: requesting ipw2200-bss.fw
Intel ICH Modem 0000:00:1e.3: PCI INT B -> GSI 20 (level, low) -> IRQ 20
Intel ICH Modem 0000:00:1e.3: setting latency timer to 64
Intel ICH 0000:00:1e.2: PCI INT A -> GSI 17 (level, low) -> IRQ 17
Intel ICH 0000:00:1e.2: setting latency timer to 64
Serial: 8250/16550 driver4 ports, IRQ sharing disabled
usb 1-1: new low speed USB device using uhci_hcd and address 2
eth1: Broadcom 44xx/47xx 10/100BaseT Ethernet 00:00:f0:7a:14:04
ipw2200: Detected geography ZZD (13 802.11bg channels, 0 802.11a channels)
sdhci-pci 0000:02:09.2: SDHCI controller found [1180:0822] (rev 17)
sdhci-pci 0000:02:09.2: power state changed by ACPI to D0
sdhci-pci 0000:02:09.2: PCI INT C -> GSI 18 (level, low) -> IRQ 18
mmc0: SDHCI controller on PCI [0000:02:09.2] using PIO
udev: renamed network interface eth1 to eth0
Synaptics Touchpad, model: 1, fw: 6.1, id: 0x2580b1, caps: 0xa04713/0x200000
input: SynPS/2 Synaptics TouchPad as /devices/platform/i8042/serio4/input/input5
udev: renamed network interface eth0_rename to eth1
usb 1-1: configuration #1 chosen from 1 choice
AC'97 0 analog subsections not ready
input: Logitech USB Optical Mouse as /devices/pci0000:00/0000:00:1d.0/usb1/1-1/1-1:1.0/input/input6
generic-usb 0003:046D:C052.0001: input: USB HID v1.10 Mouse [Logitech USB Optical Mouse] on usb-0000:00:1d.0-1/input0
usbcore: registered new interface driver usbhid
usbhid: v2.6:USB HID core driver
ieee1394: Host added: ID:BUS[0-00:1023]  GUID[0000f041200b40d5]
intel8x0_measure_ac97_clock: measured 50466 usecs
intel8x0: clocking to 48000
tun: Universal TUN/TAP device driver, 1.6
tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
loop: module loaded
ricoh-mmc: Ricoh MMC Controller disabling driver
ricoh-mmc: Copyright(c) Philip Langdale
vboxdrv: Trying to deactivate the NMI watchdog permanently...
vboxdrv: Successfully done.
vboxdrv: Found 1 processor cores.
vboxdrv: TSC mode is 'synchronous', kernel timer mode is 'normal'.
vboxdrv: Successfully loaded version 2.1.2 (interface 0x000a0009).
EXT4 FS on sda2, internal journal on sda2:8
EXT4-fs: barriers enabled
kjournald2 starting.  Commit interval 5 seconds
EXT4 FS on sda5, internal journal on sda5:8
EXT4-fs: delayed allocation enabled
EXT4-fs: file extents enabled
EXT4-fs: mballoc enabled
EXT4-fs: mounted filesystem with ordered data mode.
fuse init (API version 7.10)
platform microcode: firmware: requesting intel-ucode/06-0d-08
Microcode Update Driver: v2.00 <tigran@aivazian.fsnet.co.uk>, Peter Oruba
Microcode Update Driver: v2.00 removed.
Adding 3148700k swap on /dev/sda6.  Priority:-1 extents:1 across:3148700k
ieee80211_crypt: registered algorithm 'CCMP'
[drm] Initialized drm 1.1.0 20060810
pci 0000:00:02.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
pci 0000:00:02.0: setting latency timer to 64
[drm] Initialized i915 1.6.0 20080730 on minor 0
NET: Registered protocol family 10
ADDRCONF(NETDEV_UP): eth0: link is not ready
eth1: no IPv6 routers present
process `skype' is using obsolete setsockopt SO_BSDCOMPAT
udev: starting version 135