ache: 1024K (64 bytes/line) CPU: After all inits, caps: 078bfbff e1d3fbff 00000000 00000010 Intel machine check architecture supported. Intel machine check reporting enabled on CPU#0. CPU: AMD Athlon(tm) 64 Processor 3200+ stepping 08 Enabling fast FPU save and restore... done. Enabling unmasked SIMD FPU exception support... done. Checking 'hlt' instruction... OK. POSIX conformance testing by UNIFIX enabled ExtINT on CPU#0 ESR value before enabling vector: 00000000 ESR value after enabling vector: 00000000 ENABLING IO-APIC IRQs init IO_APIC IRQs IO-APIC (apicid-pin) 1-0, 1-16, 1-17, 1-18, 1-19, 1-20, 1-21, 1-22, 1-23 not connected. ..TIMER: vector=0x31 pin1=2 pin2=-1 Using local APIC timer interrupts. calibrating APIC timer ... ..... CPU clock speed is 2002.0259 MHz. ..... host bus clock speed is 200.0225 MHz. NET: Registered protocol family 16 PCI: PCI BIOS revision 2.10 entry at 0xf0031, last bus=1 PCI: Using configuration type 1 mtrr: v2.0 (20020519) ACPI: Subsystem revision 20040326 ACPI: Interpreter enabled ACPI: Using IOAPIC for interrupt routing ACPI: PCI Root Bridge [PCI0] (00:00) PCI: Probing PCI hardware (bus 00) ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 7 10 *11 14 15) ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 7 *10 11 14 15) ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 *5 7 10 11 14 15) ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 7 10 11 14 15) *0, disabled. ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 7 10 11 14 15) *0, disabled. ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 7 10 11 14 15) *0, disabled. ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 7 10 11 14 15) *0, disabled. ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 7 10 11 14 15) *0, disabled. Linux Plug and Play Support v0.97 (c) Adam Belay pnp: the driver 'system' has been registered usbcore: registered new driver usbfs usbcore: registered new driver hub 00:00:01[A] -> 1-16 -> IRQ 16 level low 00:00:01[B] -> 1-17 -> IRQ 17 level low 00:00:11[C] -> 1-22 -> IRQ 22 level low 00:00:0f[A] -> 1-20 -> IRQ 20 level low 00:00:10[A] -> 1-21 -> IRQ 21 level low 00:00:0b[C] -> 1-18 -> IRQ 18 level low 00:00:0b[D] -> 1-19 -> IRQ 19 level low number of MP IRQ sources: 15. number of IO-APIC #1 registers: 24. testing the IO APIC....................... IO APIC #1...... .... register #00: 01000000 ....... : physical APIC id: 01 ....... : Delivery Type: 0 ....... : LTS : 0 .... register #01: 00178003 ....... : max redirection entries: 0017 ....... : PRQ implemented: 1 ....... : IO APIC version: 0003 .... IRQ redirection table: NR Log Phy Mask Trig IRR Pol Stat Dest Deli Vect: 00 000 00 1 0 0 0 0 0 0 00 01 001 01 0 0 0 0 0 1 1 39 02 001 01 0 0 0 0 0 1 1 31 03 001 01 0 0 0 0 0 1 1 41 04 001 01 0 0 0 0 0 1 1 49 05 001 01 0 0 0 0 0 1 1 51 06 001 01 0 0 0 0 0 1 1 59 07 001 01 0 0 0 0 0 1 1 61 08 001 01 0 0 0 0 0 1 1 69 09 001 01 0 1 0 1 0 1 1 71 0a 001 01 0 0 0 0 0 1 1 79 0b 001 01 0 0 0 0 0 1 1 81 0c 001 01 0 0 0 0 0 1 1 89 0d 001 01 0 0 0 0 0 1 1 91 0e 001 01 0 0 0 0 0 1 1 99 0f 001 01 0 0 0 0 0 1 1 A1 10 001 01 1 1 0 1 0 1 1 A9 11 001 01 1 1 0 1 0 1 1 B1 12 001 01 1 1 0 1 0 1 1 D1 13 001 01 1 1 0 1 0 1 1 D9 14 001 01 1 1 0 1 0 1 1 C1 15 001 01 1 1 0 1 0 1 1 C9 16 001 01 1 1 0 1 0 1 1 B9 17 000 00 1 0 0 0 0 0 0 00 IRQ to pin mappings: IRQ0 -> 0:2 IRQ1 -> 0:1 IRQ3 -> 0:3 IRQ4 -> 0:4 IRQ5 -> 0:5 IRQ6 -> 0:6 IRQ7 -> 0:7 IRQ8 -> 0:8 IRQ9 -> 0:9 IRQ10 -> 0:10 IRQ11 -> 0:11 IRQ12 -> 0:12 IRQ13 -> 0:13 IRQ14 -> 0:14 IRQ15 -> 0:15 IRQ16 -> 0:16 IRQ17 -> 0:17 IRQ18 -> 0:18 IRQ19 -> 0:19 IRQ20 -> 0:20 IRQ21 -> 0:21 IRQ22 -> 0:22 .................................... done. PCI: Using ACPI for IRQ routing Machine check exception polling timer started. Total HugeTLB memory allocated, 0 VFS: Disk quotas dquot_6.5.1 Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) Installing knfsd (copyright (C) 1996 okir@monad.swb.de). Initializing Cryptographic API PCI: Via IRQ fixup for 0000:00:10.3, from 10 to 5 PCI: Via IRQ fixup for 0000:00:10.2, from 10 to 5 PCI: Via IRQ fixup for 0000:00:10.1, from 11 to 5 PCI: Via IRQ fixup for 0000:00:10.0, from 11 to 5 Serial: 8250/16550 driver $Revision: 1.90 $ 8 ports, IRQ sharing disabled ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A pnp: the driver 'serial' has been registered Using anticipatory io scheduler Floppy drive(s): fd0 is 1.44M FDC 0 is a post-1991 82077 loop: loaded (max 8 devices) Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2 ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx VIA8237SATA: IDE controller at PCI slot 0000:00:0f.0 VIA8237SATA: chipset revision 128 VIA8237SATA: 100% native mode on irq 20 ide2: BM-DMA at 0xd400-0xd407, BIOS settings: hde:pio, hdf:pio ide3: BM-DMA at 0xd408-0xd40f, BIOS settings: hdg:pio, hdh:pio VP_IDE: IDE controller at PCI slot 0000:00:0f.1 VP_IDE: chipset revision 6 VP_IDE: not 100% native mode: will probe irqs later VP_IDE: VIA vt8237 (rev 00) IDE UDMA133 controller on pci0000:00:0f.1 ide0: BM-DMA at 0xfc00-0xfc07, BIOS settings: hda:DMA, hdb:DMA ide1: BM-DMA at 0xfc08-0xfc0f, BIOS settings: hdc:DMA, hdd:pio hda: IBM-DJNA-371800, ATA DISK drive hdb: IC35L080AVVA07-0, ATA DISK drive ide0 at 0x1f0-0x1f7,0x3f6 on irq 14 hdc: _NEC DVD_RW ND-1300A, ATAPI CD/DVD-ROM drive ide1 at 0x170-0x177,0x376 on irq 15 pnp: the driver 'ide' has been registered hda: max request size: 128KiB hda: 35239680 sectors (18042 MB) w/1966KiB Cache, CHS=34960/16/63 hda: hda1 hda2 < hda5 hda6 hda7 > hdb: max request size: 128KiB hdb: 160836480 sectors (82348 MB) w/1863KiB Cache, CHS=65535/16/63, UDMA(100) hdb: hdb1 hdb2 < hdb5 hdb6 hdb7 hdb8 hdb9 > hdc: ATAPI 40X DVD-ROM DVD-R CD-R/RW drive, 2048kB Cache, UDMA(33) Uniform CD-ROM driver Revision: 3.20 ide-floppy driver 0.99.newide mice: PS/2 mouse device common for all mice serio: i8042 AUX port at 0x60,0x64 irq 12 serio: i8042 KBD port at 0x60,0x64 irq 1 input: AT Translated Set 2 keyboard on isa0060/serio0 NET: Registered protocol family 2 IP: routing cache hash table of 4096 buckets, 32Kbytes TCP: Hash tables configured (established 32768 bind 65536) NET: Registered protocol family 1 NET: Registered protocol family 17 PM: Reading pmdisk image. PM: Resume from disk failed. ACPI: (supports S0 S1 S3 S4 S5) ReiserFS: hdb1: found reiserfs format "3.6" with standard journal ReiserFS: hdb1: using ordered data mode ReiserFS: hdb1: journal params: device hdb1, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30 ReiserFS: hdb1: checking transaction log (hdb1) ReiserFS: hdb1: Using r5 hash to sort names VFS: Mounted root (reiserfs filesystem) readonly. Freeing unused kernel memory: 152k freed Adding 82112k swap on /dev/hdb5. Priority:-1 extents:1 Real Time Clock Driver v1.12 Linux agpgart interface v0.100 (c) Dave Jones agpgart: Detected AGP bridge 0 agpgart: Maximum main memory to use for agp memory: 439M agpgart: AGP aperture is 64M @ 0xf8000000 [drm] Initialized mga 3.1.0 20021029 on minor 0: Matrox Graphics, Inc. MGA G400 AGP SCSI subsystem initialized scsi0 : Adaptec AIC7XXX EISA/VLB/PCI SCSI HBA DRIVER, Rev 6.2.36 aic7880: Ultra Wide Channel A, SCSI Id=7, 16/253 SCBs (scsi0:A:2): 10.000MB/s transfers (10.000MHz, offset 15) Vendor: PLEXTOR Model: CD-ROM PX-32TS Rev: 1.02 Type: CD-ROM ANSI SCSI revision: 02 Vendor: sr0: scsi-1 drive Attached scsi CD-ROM sr0 at scsi0, channel 0, id 2, lun 0 IOMEGA Model: ZIP 100 Rev: J.03 Type: Direct-Access ANSI SCSI revision: 02 Attached scsi removable disk sda at scsi0, channel 0, id 5, lun 0 sk98lin: Network Device Driver v6.23 (C)Copyright 1999-2004 Marvell(R). eth0: 3Com Gigabit LOM (3C940) PrefPort:A RlmtMode:Check Link State input: ImExPS/2 Logitech Explorer Mouse on isa0060/serio1 PCI: Setting latency timer of device 0000:00:11.5 to 64 codec_read: codec 0 is not valid [0xfe0000] codec_read: codec 0 is not valid [0xfe0000] codec_read: codec 0 is not valid [0xfe0000] codec_read: codec 0 is not valid [0xfe0000] ReiserFS: hda6: found reiserfs format "3.6" with standard journal ReiserFS: hda6: using ordered data mode ReiserFS: hda6: journal params: device hda6, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30 ReiserFS: hda6: checking transaction log (hda6) ReiserFS: hda6: Using r5 hash to sort names ReiserFS: hdb7: found reiserfs format "3.6" with standard journal ReiserFS: hdb7: using ordered data mode ReiserFS: hdb7: journal params: device hdb7, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30 ReiserFS: hdb7: checking transaction log (hdb7) ReiserFS: hdb7: Using r5 hash to sort names ReiserFS: hdb9: found reiserfs format "3.6" with standard journal ReiserFS: hdb9: using ordered data mode ReiserFS: hdb9: journal params: device hdb9, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30 ReiserFS: hdb9: checking transaction log (hdb9) ReiserFS: hdb9: Using r5 hash to sort names ReiserFS: hdb8: found reiserfs format "3.6" with standard journal ReiserFS: hdb8: using ordered data mode ReiserFS: hdb8: journal params: device hdb8, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30 ReiserFS: hdb8: checking transaction log (hdb8) ReiserFS: hdb8: Using r5 hash to sort names ReiserFS: hdb6: found reiserfs format "3.6" with standard journal ReiserFS: hdb6: using ordered data mode ReiserFS: hdb6: journal params: device hdb6, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30 ReiserFS: hdb6: checking transaction log (hdb6) ReiserFS: hdb6: Using r5 hash to sort names Linux video capture interface: v1.00 bttv: driver version 0.9.14 loaded bttv: using 8 buffers with 2080k (520 pages) each for capture bttv: Bt8xx card found (0). bttv0: Bt878 (rev 17) at 0000:00:0d.0, irq: 18, latency: 64, mmio: 0xf7e00000 bttv0: detected: Hauppauge WinTV [card=10], PCI subsystem ID is 0070:13eb bttv0: using: Hauppauge (bt878) [card=10,autodetected] bttv0: gpio: en=00000000, out=00000000 in=00ffffdb [init] bttv0: Hauppauge/Voodoo msp34xx: reset line init [5] bttv0: Hauppauge eeprom: model=61344, tuner=Philips FM1216 (5), radio=yes bttv0: using tuner=5 bttv0: i2c: checking for MSP34xx @ 0x80... found msp34xx: init: chip=MSP3415D-B3 +nicam +simple bttv0: i2c: checking for TDA9875 @ 0xb0... not found bttv0: i2c: checking for TDA7432 @ 0x8a... not found msp3410: daemon started tvaudio: TV audio decoder + audio/video mux driver tvaudio: known chips: tda9840,tda9873h,tda9874h/a,tda9850,tda9855,tea6300,tea6420,tda8425,pic16c54 (PV951),ta8874z tuner: chip found at addr 0xc2 i2c-bus bt878 #0 [sw] tuner: type set to 5 (Philips PAL_BG (FI1216 and compatibles)) by bt878 #0 [sw] bttv0: registered device video0 bttv0: registered device vbi0 bttv0: registered device radio0 bttv0: PLL: 28636363 => 35468950 .. ok libata version 1.02 loaded. USB Universal Host Controller Interface driver v2.2 uhci_hcd 0000:00:10.0: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller uhci_hcd 0000:00:10.0: irq 21, io base 0000b400 uhci_hcd 0000:00:10.0: new USB bus registered, assigned bus number 1 hub 1-0:1.0: USB hub found hub 1-0:1.0: 2 ports detected uhci_hcd 0000:00:10.1: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (#2) uhci_hcd 0000:00:10.1: irq 21, io base 0000b800 uhci_hcd 0000:00:10.1: new USB bus registered, assigned bus number 2 hub 2-0:1.0: USB hub found hub 2-0:1.0: 2 ports detected uhci_hcd 0000:00:10.2: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (#3) uhci_hcd 0000:00:10.2: irq 21, io base 0000c000 uhci_hcd 0000:00:10.2: new USB bus registered, assigned bus number 3 hub 3-0:1.0: USB hub found hub 3-0:1.0: 2 ports detected uhci_hcd 0000:00:10.3: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (#4) uhci_hcd 0000:00:10.3: irq 21, io base 0000c400 uhci_hcd 0000:00:10.3: new USB bus registered, assigned bus number 4 hub 4-0:1.0: USB hub found hub 4-0:1.0: 2 ports detected ehci_hcd 0000:00:10.4: VIA Technologies, Inc. USB 2.0 ehci_hcd 0000:00:10.4: irq 21, pci mem e0e4c000 ehci_hcd 0000:00:10.4: new USB bus registered, assigned bus number 5 ehci_hcd 0000:00:10.4: USB 2.0 enabled, EHCI 1.00, driver 2004-May-10 hub 5-0:1.0: USB hub found hub 5-0:1.0: 8 ports detected eth0: network connection up using port A speed: 100 autonegotiation: yes duplex mode: half flowctrl: none irq moderation: disabled scatter-gather: enabled ACPI: Processor [CPU1] (supports C1) ACPI: Power Button (FF) [PWRF] ACPI: Sleep Button (CM) [SLPB] pg: pg version 1.02, major 97 pga: Autoprobe failed pg: No ATAPI device detected pnp: the driver 'parport_pc' has been registered parport0: PC-style at 0x378 [PCSPP] parport0: irq 7 detected ppdev: user-space parallel port driver ppdev0: registered pardevice ppdev0: unregistered pardevice agpgart: Found an AGP 3.5 compliant device at 0000:00:00.0. agpgart: Device is in legacy mode, falling back to 2.x agpgart: Putting AGP V2 device at 0000:00:00.0 into 0x mode agpgart: Putting AGP V2 device at 0000:01:00.0 into 0x mode atkbd.c: Unknown key released (translated set 2, code 0x7a on isa0060/serio0). atkbd.c: This is an XFree86 bug. It shouldn't access hardware directly. atkbd.c: Unknown key released (translated set 2, code 0x7a on isa0060/serio0). atkbd.c: This is an XFree86 bug. It shouldn't access hardware directly. [drm] Module unloaded [drm] Initialized mga 3.1.0 20021029 on minor 0: Matrox Graphics, Inc. MGA G400 AGP agpgart: Found an AGP 3.5 compliant device at 0000:00:00.0. agpgart: Device is in legacy mode, falling back to 2.x agpgart: Putting AGP V2 device at 0000:00:00.0 into 0x mode agpgart: Putting AGP V2 device at 0000:01:00.0 into 0x mode atkbd.c: Unknown key released (translated set 2, code 0x7a on isa0060/serio0). atkbd.c: This is an XFree86 bug. It shouldn't access hardware directly. atkbd.c: Unknown key released (translated set 2, code 0x7a on isa0060/serio0). atkbd.c: This is an XFree86 bug. It shouldn't access hardware directly. agpgart: Found an AGP 3.5 compliant device at 0000:00:00.0. agpgart: Device is in legacy mode, falling back to 2.x agpgart: Putting AGP V2 device at 0000:00:00.0 into 0x mode agpgart: Putting AGP V2 device at 0000:01:00.0 into 0x mode atkbd.c: Unknown key released (translated set 2, code 0x7a on isa0060/serio0). atkbd.c: This is an XFree86 bug. It shouldn't access hardware directly. atkbd.c: Unknown key released (translated set 2, code 0x7a on isa0060/serio0). atkbd.c: This is an XFree86 bug. It shouldn't access hardware directly.