[ 0.000000] Using PowerMac machine description [ 0.000000] Total memory = 1024MB; using 2048kB for hash table (at cfe00000) [ 0.000000] Linux version 2.6.33.2-vanilla1 (root@aerith) (gcc version 4.4.3 (Ubuntu 4.4.3-4ubuntu5) ) #3 Wed Apr 7 14:52:57 PDT 2010 [ 0.000000] Found initrd at 0xc1b00000:0xc1f90000 [ 0.000000] Found UniNorth memory controller & host bridge @ 0xf8000000 revision: 0xd2 [ 0.000000] Mapped at 0xff7c0000 [ 0.000000] Found a Intrepid mac-io controller, rev: 0, mapped at 0xff740000 [ 0.000000] Processor NAP mode on idle enabled. [ 0.000000] PowerMac motherboard: PowerBook G4 15" [ 0.000000] bootconsole [udbg0] enabled [ 0.000000] Found UniNorth PCI host bridge at 0x00000000f0000000. Firmware bus number: 0->1 [ 0.000000] PCI host bridge /pci@f0000000 ranges: [ 0.000000] MEM 0x00000000f1000000..0x00000000f1ffffff -> 0x00000000f1000000 [ 0.000000] IO 0x00000000f0000000..0x00000000f07fffff -> 0x0000000000000000 [ 0.000000] MEM 0x00000000b0000000..0x00000000bfffffff -> 0x00000000b0000000 [ 0.000000] Found UniNorth PCI host bridge at 0x00000000f2000000. Firmware bus number: 0->1 [ 0.000000] PCI host bridge /pci@f2000000 (primary) ranges: [ 0.000000] MEM 0x00000000f3000000..0x00000000f3ffffff -> 0x00000000f3000000 [ 0.000000] IO 0x00000000f2000000..0x00000000f27fffff -> 0x0000000000000000 [ 0.000000] MEM 0x0000000080000000..0x00000000afffffff -> 0x0000000080000000 [ 0.000000] Found UniNorth PCI host bridge at 0x00000000f4000000. Firmware bus number: 0->1 [ 0.000000] PCI host bridge /pci@f4000000 ranges: [ 0.000000] MEM 0x00000000f5000000..0x00000000f5ffffff -> 0x00000000f5000000 [ 0.000000] IO 0x00000000f4000000..0x00000000f47fffff -> 0x0000000000000000 [ 0.000000] via-pmu: Server Mode is disabled [ 0.000000] PMU driver v2 initialized for Core99, firmware: 0c [ 0.000000] nvram: Checking bank 0... [ 0.000000] nvram: gen0=512, gen1=511 [ 0.000000] nvram: Active bank is: 0 [ 0.000000] nvram: OF partition at 0x410 [ 0.000000] nvram: XP partition at 0x1020 [ 0.000000] nvram: NR partition at 0x1120 [ 0.000000] Top of RAM: 0x40000000, Total RAM: 0x40000000 [ 0.000000] Memory hole size: 0MB [ 0.000000] Zone PFN ranges: [ 0.000000] DMA 0x00000000 -> 0x00030000 [ 0.000000] Normal 0x00030000 -> 0x00030000 [ 0.000000] HighMem 0x00030000 -> 0x00040000 [ 0.000000] Movable zone start PFN for each node [ 0.000000] early_node_map[1] active PFN ranges [ 0.000000] 0: 0x00000000 -> 0x00040000 [ 0.000000] On node 0 totalpages: 262144 [ 0.000000] free_area_init_node: node 0, pgdat c055e14c, node_mem_map c05e1000 [ 0.000000] DMA zone: 1536 pages used for memmap [ 0.000000] DMA zone: 0 pages reserved [ 0.000000] DMA zone: 195072 pages, LIFO batch:31 [ 0.000000] HighMem zone: 512 pages used for memmap [ 0.000000] HighMem zone: 65024 pages, LIFO batch:15 [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 260096 [ 0.000000] Kernel command line: root=/dev/hda3 ro [ 0.000000] PID hash table entries: 4096 (order: 2, 16384 bytes) [ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes) [ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes) [ 0.000000] High memory: 262144k [ 0.000000] Memory: 1025744k/1048576k available (5324k kernel code, 22084k reserved, 216k data, 426k bss, 196k init) [ 0.000000] Kernel virtual memory layout: [ 0.000000] * 0xfffd0000..0xfffff000 : fixmap [ 0.000000] * 0xff800000..0xffc00000 : highmem PTEs [ 0.000000] * 0xfde27000..0xff800000 : early ioremap [ 0.000000] * 0xf1000000..0xfde27000 : vmalloc & ioremap [ 0.000000] SLUB: Genslabs=13, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 [ 0.000000] Hierarchical RCU implementation. [ 0.000000] NR_IRQS:512 nr_irqs:512 [ 0.000000] mpic: Setting up MPIC " MPIC 1 " version 1.2 at 80040000, max 4 CPUs [ 0.000000] mpic: ISU size: 64, shift: 6, mask: 3f [ 0.000000] mpic: Initializing for 64 sources [ 0.000000] GMT Delta read from XPRAM: 0 minutes, DST: off [ 0.000000] time_init: decrementer frequency = 18.432000 MHz [ 0.000000] time_init: processor frequency = 1499.999994 MHz [ 0.000000] clocksource: timebase mult[d9038e4] shift[22] registered [ 0.000000] clockevent: decrementer mult[4b7f5a5] shift[32] cpu[0] [ 0.000000] Console: colour dummy device 80x25 [ 0.000000] console [tty0] enabled, bootconsole disabled [ 0.001137] Security Framework initialized [ 0.001165] SELinux: Disabled at boot. [ 0.001186] Mount-cache hash table entries: 512 [ 0.001591] device-tree: Duplicate name in /cpus/PowerPC,G4@0, renamed to "l2-cache#1" [ 0.005051] devtmpfs: initialized [ 0.005400] NET: Registered protocol family 16 [ 0.006026] MPC7450 family performance monitor hardware support registered [ 0.006085] alloc irq_desc for 42 on node 0 [ 0.006091] alloc kstat_irqs on node 0 [ 0.006101] irq: irq 42 on host /pci@f2000000/mac-io@17/interrupt-controller@40000 mapped to virtual irq 42 [ 0.006137] KeyWest i2c @0xf8001003 irq 42 /uni-n@f8000000/i2c@f8001000 [ 0.006155] channel 1 bus /uni-n@f8000000/i2c@f8001000/i2c-bus@1 [ 0.006169] channel 0 bus /uni-n@f8000000/i2c@f8001000/i2c-bus@0 [ 0.006206] alloc irq_desc for 26 on node 0 [ 0.006211] alloc kstat_irqs on node 0 [ 0.006217] irq: irq 26 on host /pci@f2000000/mac-io@17/interrupt-controller@40000 mapped to virtual irq 26 [ 0.006238] KeyWest i2c @0x80018000 irq 26 /pci@f2000000/mac-io@17/i2c@18000 [ 0.006254] channel 0 bus /pci@f2000000/mac-io@17/i2c@18000/i2c-bus@0 [ 0.006278] PMU i2c /pci@f2000000/mac-io@17/via-pmu@16000/pmu-i2c [ 0.006293] channel 1 bus [ 0.006303] channel 2 bus [ 0.006394] alloc irq_desc for 25 on node 0 [ 0.006399] alloc kstat_irqs on node 0 [ 0.006405] irq: irq 25 on host /pci@f2000000/mac-io@17/interrupt-controller@40000 mapped to virtual irq 25 [ 0.006436] alloc irq_desc for 47 on node 0 [ 0.006441] alloc kstat_irqs on node 0 [ 0.006447] irq: irq 47 on host /pci@f2000000/mac-io@17/interrupt-controller@40000 mapped to virtual irq 47 [ 0.006582] PCI: Probing PCI hardware [ 0.006756] pci 0000:00:10.0: reg 10: [mem 0xb8000000-0xbfffffff pref] [ 0.006767] pci 0000:00:10.0: reg 14: [io 0x0400-0x04ff] [ 0.006777] pci 0000:00:10.0: reg 18: [mem 0xb0000000-0xb000ffff] [ 0.006796] pci 0000:00:10.0: reg 30: [mem 0xb0020000-0xb003ffff pref] [ 0.006823] pci 0000:00:10.0: supports D1 D2 [ 0.006882] alloc irq_desc for 48 on node 0 [ 0.006887] alloc kstat_irqs on node 0 [ 0.006893] irq: irq 48 on host /pci@f2000000/mac-io@17/interrupt-controller@40000 mapped to virtual irq 48 [ 0.007184] pci 0001:10:12.0: reg 10: [mem 0xa0006000-0xa0007fff] [ 0.007228] pci 0001:10:12.0: supports D1 D2 [ 0.007234] pci 0001:10:12.0: PME# supported from D0 D1 D2 D3hot D3cold [ 0.007243] pci 0001:10:12.0: PME# disabled [ 0.007279] pci 0001:10:13.0: reg 10: [mem 0xa0004000-0xa0004fff] [ 0.007303] pci 0001:10:13.0: supports D1 D2 [ 0.007308] pci 0001:10:13.0: PME# supported from D0 D1 D2 D3hot D3cold [ 0.007316] pci 0001:10:13.0: PME# disabled [ 0.007354] pci 0001:10:17.0: reg 10: [mem 0x80000000-0x8007ffff] [ 0.007410] pci 0001:10:19.0: reg 10: [mem 0x00000000-0x00000fff] [ 0.007467] pci 0001:10:1a.0: reg 10: [mem 0xa0003000-0xa0003fff] [ 0.007529] pci 0001:10:1b.0: reg 10: [mem 0xa0002000-0xa0002fff] [ 0.007573] pci 0001:10:1b.0: supports D1 D2 [ 0.007579] pci 0001:10:1b.0: PME# supported from D0 D1 D2 D3hot D3cold [ 0.007586] pci 0001:10:1b.0: PME# disabled [ 0.007621] pci 0001:10:1b.1: reg 10: [mem 0xa0001000-0xa0001fff] [ 0.007664] pci 0001:10:1b.1: supports D1 D2 [ 0.007670] pci 0001:10:1b.1: PME# supported from D0 D1 D2 D3hot D3cold [ 0.007678] pci 0001:10:1b.1: PME# disabled [ 0.007712] pci 0001:10:1b.2: reg 10: [mem 0xa0000000-0xa00000ff] [ 0.007756] pci 0001:10:1b.2: supports D1 D2 [ 0.007761] pci 0001:10:1b.2: PME# supported from D0 D1 D2 D3hot D3cold [ 0.007769] pci 0001:10:1b.2: PME# disabled [ 0.007824] alloc irq_desc for 52 on node 0 [ 0.007829] alloc kstat_irqs on node 0 [ 0.007835] irq: irq 52 on host /pci@f2000000/mac-io@17/interrupt-controller@40000 mapped to virtual irq 52 [ 0.007863] alloc irq_desc for 53 on node 0 [ 0.007867] alloc kstat_irqs on node 0 [ 0.007873] irq: irq 53 on host /pci@f2000000/mac-io@17/interrupt-controller@40000 mapped to virtual irq 53 [ 0.007911] alloc irq_desc for 28 on node 0 [ 0.007916] alloc kstat_irqs on node 0 [ 0.007921] irq: irq 28 on host /pci@f2000000/mac-io@17/interrupt-controller@40000 mapped to virtual irq 28 [ 0.007953] alloc irq_desc for 29 on node 0 [ 0.007957] alloc kstat_irqs on node 0 [ 0.007963] irq: irq 29 on host /pci@f2000000/mac-io@17/interrupt-controller@40000 mapped to virtual irq 29 [ 0.007993] alloc irq_desc for 63 on node 0 [ 0.007997] alloc kstat_irqs on node 0 [ 0.008003] irq: irq 63 on host /pci@f2000000/mac-io@17/interrupt-controller@40000 mapped to virtual irq 63 [ 0.008651] pci 0002:24:0d.0: reg 10: [mem 0xf5004000-0xf5007fff] [ 0.008706] pci 0002:24:0e.0: reg 10: [mem 0xf5000000-0xf5000fff] [ 0.008743] pci 0002:24:0e.0: supports D1 D2 [ 0.008749] pci 0002:24:0e.0: PME# supported from D0 D1 D2 D3hot [ 0.008756] pci 0002:24:0e.0: PME# disabled [ 0.008781] pci 0002:24:0f.0: reg 10: [mem 0xf5200000-0xf53fffff] [ 0.008805] pci 0002:24:0f.0: reg 30: [mem 0xf5100000-0xf51fffff pref] [ 0.008864] alloc irq_desc for 39 on node 0 [ 0.008868] alloc kstat_irqs on node 0 [ 0.008875] irq: irq 39 on host /pci@f2000000/mac-io@17/interrupt-controller@40000 mapped to virtual irq 39 [ 0.008903] alloc irq_desc for 40 on node 0 [ 0.008907] alloc kstat_irqs on node 0 [ 0.008913] irq: irq 40 on host /pci@f2000000/mac-io@17/interrupt-controller@40000 mapped to virtual irq 40 [ 0.008943] alloc irq_desc for 41 on node 0 [ 0.008947] alloc kstat_irqs on node 0 [ 0.008953] irq: irq 41 on host /pci@f2000000/mac-io@17/interrupt-controller@40000 mapped to virtual irq 41 [ 0.009284] PCI 0000:00 Cannot reserve Legacy IO [io 0x802000-0x802fff] [ 0.009311] pci 0001:10:13.0: BAR 9: assigned [mem 0x84000000-0x87ffffff pref] [ 0.009330] pci 0001:10:13.0: BAR 10: assigned [mem 0x88000000-0x8bffffff] [ 0.009346] pci 0001:10:13.0: BAR 7: assigned [io 0x1000-0x10ff] [ 0.009360] pci 0001:10:13.0: BAR 8: assigned [io 0x1100-0x11ff] [ 0.009375] pci 0001:10:13.0: CardBus bridge to [bus 11-14] [ 0.009388] pci 0001:10:13.0: bridge window [io 0x1000-0x10ff] [ 0.009411] pci 0001:10:13.0: bridge window [io 0x1100-0x11ff] [ 0.009430] pci 0001:10:13.0: bridge window [mem 0x84000000-0x87ffffff pref] [ 0.009456] pci 0001:10:13.0: bridge window [mem 0x88000000-0x8bffffff] [ 0.009493] pci_bus 0000:00: resource 0 [io 0x802000-0x1001fff] [ 0.009501] pci_bus 0000:00: resource 1 [mem 0xf1000000-0xf1ffffff] [ 0.009508] pci_bus 0000:00: resource 2 [mem 0xb0000000-0xbfffffff] [ 0.009515] pci_bus 0001:10: resource 0 [io 0x0000-0x7fffff] [ 0.009523] pci_bus 0001:10: resource 1 [mem 0xf3000000-0xf3ffffff] [ 0.009530] pci_bus 0001:10: resource 2 [mem 0x80000000-0xafffffff] [ 0.009537] pci_bus 0001:11: resource 0 [io 0x1000-0x10ff] [ 0.009544] pci_bus 0001:11: resource 1 [io 0x1100-0x11ff] [ 0.009551] pci_bus 0001:11: resource 2 [mem 0x84000000-0x87ffffff pref] [ 0.009559] pci_bus 0001:11: resource 3 [mem 0x88000000-0x8bffffff] [ 0.009567] pci_bus 0002:24: resource 0 [io 0xff7fe000-0xffffdfff] [ 0.009574] pci_bus 0002:24: resource 1 [mem 0xf5000000-0xf5ffffff] [ 0.011004] bio: create slab at 0 [ 0.011258] vgaarb: device added: PCI:0000:00:10.0,decodes=io+mem,owns=mem,locks=none [ 0.011304] vgaarb: loaded [ 0.011514] usbcore: registered new interface driver usbfs [ 0.011564] usbcore: registered new interface driver hub [ 0.011632] usbcore: registered new device driver usb [ 0.011976] NET: Registered protocol family 8 [ 0.011993] NET: Registered protocol family 20 [ 0.012035] Switching to clocksource timebase [ 0.012453] NET: Registered protocol family 2 [ 0.012530] IP route cache hash table entries: 32768 (order: 5, 131072 bytes) [ 0.012963] TCP established hash table entries: 131072 (order: 8, 1048576 bytes) [ 0.015172] TCP bind hash table entries: 65536 (order: 6, 262144 bytes) [ 0.015770] TCP: Hash tables configured (established 131072 bind 65536) [ 0.015794] TCP reno registered [ 0.015812] UDP hash table entries: 512 (order: 1, 8192 bytes) [ 0.015848] UDP-Lite hash table entries: 512 (order: 1, 8192 bytes) [ 0.016069] NET: Registered protocol family 1 [ 0.016184] PCI: CLS mismatch (32 != 1020), using 32 bytes [ 0.016331] Trying to unpack rootfs image as initramfs... [ 0.263389] Freeing initrd memory: 4672k freed [ 0.264203] Registering PowerMac CPU frequency driver [ 0.264224] Low: 749 Mhz, High: 1499 Mhz, Boot: 749 Mhz [ 0.269003] audit: initializing netlink socket (disabled) [ 0.269034] type=2000 audit(1270678223.266:1): initialized [ 0.269248] highmem bounce pool size: 64 pages [ 0.271070] VFS: Disk quotas dquot_6.5.2 [ 0.271148] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) [ 0.271220] fuse init (API version 7.13) [ 0.271369] msgmni has been set to 1501 [ 0.271652] alg: No test for stdrng (krng) [ 0.271676] io scheduler noop registered [ 0.271787] io scheduler cfq registered (default) [ 0.271935] Using unsupported 1280x854 ATY,Jasper_A at b8008000, depth=8, pitch=1280 [ 0.293413] Console: switching to colour frame buffer device 160x53 [ 0.314568] fb0: Open Firmware frame buffer device on /pci@f0000000/ATY,JasperParent@10/ATY,Jasper_A@0 [ 0.314892] Using unsupported 640x480 ATY,Jasper_B at ba008000, depth=8, pitch=768 [ 0.315194] fb1: Open Firmware frame buffer device on /pci@f0000000/ATY,JasperParent@10/ATY,Jasper_B@1 [ 0.317413] Generic non-volatile memory driver v1.1 [ 0.317613] Linux agpgart interface v0.103 [ 0.317757] agpgart-uninorth 0000:00:0b.0: Apple UniNorth 2 chipset [ 0.319415] agpgart-uninorth 0000:00:0b.0: configuring for size idx: 64 [ 0.319665] agpgart-uninorth 0000:00:0b.0: AGP aperture is 256M @ 0x0 [ 0.319950] [drm] Initialized drm 1.1.0 20060810 [ 0.320105] [drm] radeon defaulting to kernel modesetting. [ 0.320264] [drm] radeon kernel modesetting enabled. [ 0.320475] radeon 0000:00:10.0: enabling device (0006 -> 0007) [ 0.324646] [drm] radeon: Initializing kernel modesetting. [ 0.324947] [drm] register mmio base: 0xB0000000 [ 0.325086] [drm] register mmio size: 65536 [ 0.325226] radeon 0000:00:10.0: Invalid ROM contents [ 0.325438] radeon 0000:00:10.0: Invalid ROM contents [ 0.325591] [drm:radeon_get_bios] *ERROR* Unable to locate a BIOS ROM [ 0.325984] [drm] GPU reset succeed (RBBM_STATUS=0x00000140) [ 0.326154] [drm] Using generic clock info [ 0.326298] [drm] Generation 2 PCI interface, using max accessible memory [ 0.326523] agpgart-uninorth 0000:00:0b.0: putting AGP V2 device into 4x mode [ 0.326736] radeon 0000:00:10.0: putting AGP V2 device into 4x mode [ 0.326969] [drm] radeon: VRAM 64M [ 0.327067] [drm] radeon: VRAM from 0x10000000 to 0x13FFFFFF [ 0.327231] [drm] radeon: GTT 256M [ 0.327329] [drm] radeon: GTT from 0x00000000 to 0x0FFFFFFF [ 0.327545] [drm] radeon: irq initialized. [ 0.334255] [drm] Detected VRAM RAM=64M, BAR=128M [ 0.340851] [drm] RAM width 128bits DDR [ 0.347421] [TTM] Zone kernel: Available graphics memory: 384510 kiB. [ 0.354015] [TTM] Zone highmem: Available graphics memory: 515582 kiB. [ 0.360543] [drm] radeon: 64M of VRAM memory ready [ 0.367014] [drm] radeon: 256M of GTT memory ready. [ 0.373642] [drm] radeon: 1 quad pipes, 1 Z pipes initialized. [ 0.380033] [drm] radeon: cp idle (0x10000C03) [ 0.386411] [drm] Loading R300 Microcode [ 0.392688] platform radeon_cp.0: firmware: using built-in firmware radeon/R300_cp.bin [ 0.400794] [drm] radeon: ring at 0x0000000000000000 [ 0.407305] [drm] ring test succeeded in 4 usecs [ 0.415173] [drm] radeon: ib pool ready. [ 2.938727] [drm:radeon_fence_wait] *ERROR* fence(efa84be0:0x00000001) 510ms timeout going to reset GPU [ 2.946727] [drm] CP reset succeed (RBBM_STATUS=0x00000140) [ 2.953339] [drm] radeon: cp idle (0x10000000) [ 2.959933] [drm] radeon: ring at 0x0000000000000000 [ 3.097824] [drm:r100_ring_test] *ERROR* radeon: ring test failed (sracth(0x15E8)=0xCAFEDEAD) [ 3.104540] [drm:r100_cp_init] *ERROR* radeon: cp isn't working (-22). [ 3.111303] [drm:r300_gpu_reset] *ERROR* Failed to reset GPU (RBBM_STATUS=0x80010140) [ 3.118195] [drm:radeon_fence_wait] *ERROR* fence(efa84be0:0x00000001) 696ms timeout [ 3.125183] [drm:radeon_fence_wait] *ERROR* last signaled fence(0x00000001) [ 3.263750] [drm:r100_ib_test] *ERROR* radeon: ib test failed (sracth(0x15E4)=0xCAFEDEAD) [ 3.270710] radeon 0000:00:10.0: failled testing IB (-22). [ 3.277734] radeon 0000:00:10.0: failled initializing IB (-22). [ 3.284505] radeon 0000:00:10.0: Disabling GPU acceleration [ 3.422014] [drm:r100_cp_fini] *ERROR* Wait for CP idle timeout, shutting down CP. [ 3.428740] [drm] radeon: cp finalized [ 3.435421] [drm] GPU reset succeed (RBBM_STATUS=0x00000140) [ 3.441968] [drm] radeon: cp finalized [ 3.448503] [TTM] Zone kernel: Used memory at exit: 0 kiB. [ 3.455076] [TTM] Zone highmem: Used memory at exit: 0 kiB. [ 3.461602] [drm] radeon: ttm finalized [ 3.468049] [drm] Forcing AGP to PCI mode [ 3.474464] radeon 0000:00:10.0: Invalid ROM contents [ 3.480947] radeon 0000:00:10.0: Invalid ROM contents [ 3.487295] [drm:radeon_get_bios] *ERROR* Unable to locate a BIOS ROM [ 3.493888] [drm] GPU reset succeed (RBBM_STATUS=0x00000140) [ 3.500286] [drm] Using generic clock info [ 3.506716] [drm] Generation 2 PCI interface, using max accessible memory [ 3.513240] [drm] radeon: VRAM 64M [ 3.519783] [drm] radeon: VRAM from 0x00000000 to 0x03FFFFFF [ 3.526326] [drm] radeon: GTT 512M [ 3.532766] [drm] radeon: GTT from 0x20000000 to 0x3FFFFFFF [ 3.539257] [drm] radeon: irq initialized. [ 3.545648] [drm] Detected VRAM RAM=64M, BAR=128M [ 3.551975] [drm] RAM width 128bits DDR [ 3.558266] [TTM] Zone kernel: Available graphics memory: 384510 kiB. [ 3.564593] [TTM] Zone highmem: Available graphics memory: 515582 kiB. [ 3.570903] [drm] radeon: 64M of VRAM memory ready [ 3.577198] [drm] radeon: 512M of GTT memory ready. [ 3.583460] [drm] GART: num cpu pages 131072, num gpu pages 131072 [ 3.592969] [drm] radeon: 1 quad pipes, 1 Z pipes initialized. [ 3.599463] [drm] radeon: cp idle (0x10000000) [ 3.606080] [drm] radeon: ring at 0x0000000020000000 [ 3.612428] [drm] ring test succeeded in 3 usecs [ 3.618951] [drm] radeon: ib pool ready. [ 3.625267] [drm] ib test succeeded in 0 usecs [ 3.631636] [drm] Connector Table: 3 (powerbook external tmds) [ 3.637999] [drm] Panel info derived from registers [ 3.644316] [drm] Panel Size 1280x854 [ 3.650844] [drm] Radeon Display Connectors [ 3.657048] [drm] Connector 0: [ 3.663078] [drm] LVDS [ 3.669038] [drm] DDC: 0x64 0x64 0x64 0x64 0x64 0x64 0x64 0x64 [ 3.675113] [drm] Encoders: [ 3.680998] [drm] LCD1: INTERNAL_LVDS [ 3.686774] [drm] Connector 1: [ 3.692473] [drm] DVI-I [ 3.698145] [drm] HPD2 [ 3.703641] [drm] DDC: 0x60 0x60 0x60 0x60 0x60 0x60 0x60 0x60 [ 3.709157] [drm] Encoders: [ 3.714520] [drm] DFP2: INTERNAL_DVO1 [ 3.719810] [drm] CRT1: INTERNAL_DAC1 [ 3.725025] [drm] Connector 2: [ 3.730096] [drm] S-video [ 3.735013] [drm] Encoders: [ 3.739904] [drm] TV1: INTERNAL_DAC2 [ 4.043224] [drm] Determined LVDS native mode details from EDID [ 4.144525] [drm] fb mappable at 0xB8040000 [ 4.149378] [drm] vram apper at 0xB8000000 [ 4.154122] [drm] size 4372480 [ 4.158786] [drm] fb depth is 24 [ 4.163392] [drm] pitch is 5120 [ 4.168049] fb: conflicting fb hw usage radeondrmfb vs OFfb ATY,Jasper - removing generic driver [ 4.172960] Console: switching to colour dummy device 80x25 [ 4.173091] Trying to free nonexistent resource <00000000b8008000-00000000b8112dff> [ 4.173209] fb0: radeondrmfb frame buffer device [ 4.173218] registered panic notifier [ 4.173231] [drm] Initialized radeon 2.0.0 20080528 for 0000:00:10.0 on minor 0 [ 4.174674] brd: module loaded [ 4.174737] MacIO PCI driver attached to Intrepid chipset [ 4.174977] alloc irq_desc for 32 on node 0 [ 4.174982] alloc kstat_irqs on node 0 [ 4.174989] irq: irq 32 on host /pci@f2000000/mac-io@17/interrupt-controller@40000 mapped to virtual irq 32 [ 4.175118] alloc irq_desc for 24 on node 0 [ 4.175121] alloc kstat_irqs on node 0 [ 4.175124] irq: irq 24 on host /pci@f2000000/mac-io@17/interrupt-controller@40000 mapped to virtual irq 24 [ 4.175133] alloc irq_desc for 16 on node 0 [ 4.175136] alloc kstat_irqs on node 0 [ 4.175139] irq: irq 12 on host /pci@f2000000/mac-io@17/interrupt-controller@40000 mapped to virtual irq 16 [ 4.175196] alloc irq_desc for 22 on node 0 [ 4.175198] alloc kstat_irqs on node 0 [ 4.175202] irq: irq 22 on host /pci@f2000000/mac-io@17/interrupt-controller@40000 mapped to virtual irq 22 [ 4.175211] alloc irq_desc for 17 on node 0 [ 4.175214] alloc kstat_irqs on node 0 [ 4.175217] irq: irq 5 on host /pci@f2000000/mac-io@17/interrupt-controller@40000 mapped to virtual irq 17 [ 4.175226] alloc irq_desc for 18 on node 0 [ 4.175228] alloc kstat_irqs on node 0 [ 4.175231] irq: irq 6 on host /pci@f2000000/mac-io@17/interrupt-controller@40000 mapped to virtual irq 18 [ 4.175291] alloc irq_desc for 23 on node 0 [ 4.175294] alloc kstat_irqs on node 0 [ 4.175297] irq: irq 23 on host /pci@f2000000/mac-io@17/interrupt-controller@40000 mapped to virtual irq 23 [ 4.175307] alloc irq_desc for 19 on node 0 [ 4.175309] alloc kstat_irqs on node 0 [ 4.175312] irq: irq 7 on host /pci@f2000000/mac-io@17/interrupt-controller@40000 mapped to virtual irq 19 [ 4.175321] alloc irq_desc for 20 on node 0 [ 4.175324] alloc kstat_irqs on node 0 [ 4.175326] irq: irq 8 on host /pci@f2000000/mac-io@17/interrupt-controller@40000 mapped to virtual irq 20 [ 4.175566] input: Macintosh mouse button emulation as /devices/virtual/input/input0 [ 4.175825] Uniform Multi-Platform E-IDE driver [ 4.175972] ide-pmac 0002:24:0d.0: enabling device (0000 -> 0002) [ 4.176077] adb: starting probe task... [ 4.176090] adb: finished probe task... [ 5.192065] ide-pmac: Found Apple UniNorth ATA-6 controller (PCI), bus ID 3, irq 39 [ 5.192096] Probing IDE interface ide0... [ 5.465574] hda: TOSHIBA MK8026GAX, ATA DISK drive [ 6.105448] hda: host max PIO4 wanted PIO255(auto-tune) selected PIO4 [ 6.105495] hda: UDMA/100 mode selected [ 6.105575] ide0 at 0xf1192000-0xf1192070,0xf1192160 on irq 39 [ 7.122135] ide-pmac: Found Apple KeyLargo ATA-3 controller (macio), bus ID 0, irq 24 [ 7.122160] Probing IDE interface ide1... [ 7.502241] hdc: MATSHITACD-RW CW-8123, ATAPI CD/DVD-ROM drive [ 7.822090] hdc: host max PIO4 wanted PIO255(auto-tune) selected PIO4 [ 7.822277] hdc: MWDMA2 mode selected [ 7.822494] ide1 at 0xf107c000-0xf107c070,0xf107c160 on irq 24 [ 7.822616] Fixed MDIO Bus: probed [ 7.822734] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 7.822778] ehci_hcd 0001:10:1b.2: enabling device (0004 -> 0006) [ 7.822797] ehci_hcd 0001:10:1b.2: EHCI Host Controller [ 7.822883] ehci_hcd 0001:10:1b.2: new USB bus registered, assigned bus number 1 [ 7.845419] ehci_hcd 0001:10:1b.2: irq 63, io mem 0xa0000000 [ 7.855395] ehci_hcd 0001:10:1b.2: USB 2.0 started, EHCI 1.00 [ 7.855625] hub 1-0:1.0: USB hub found [ 7.855641] hub 1-0:1.0: 5 ports detected [ 7.855748] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 7.855786] Apple USB OHCI 0001:10:19.0 disabled by firmware [ 7.855808] ohci_hcd 0001:10:1a.0: enabling device (0000 -> 0002) [ 7.855830] ohci_hcd 0001:10:1a.0: OHCI Host Controller [ 7.855889] ohci_hcd 0001:10:1a.0: new USB bus registered, assigned bus number 2 [ 7.855923] ohci_hcd 0001:10:1a.0: irq 29, io mem 0xa0003000 [ 7.928407] hub 2-0:1.0: USB hub found [ 7.928421] hub 2-0:1.0: 2 ports detected [ 7.928489] ohci_hcd 0001:10:1b.0: enabling device (0000 -> 0002) [ 7.928507] ohci_hcd 0001:10:1b.0: OHCI Host Controller [ 7.928571] ohci_hcd 0001:10:1b.0: new USB bus registered, assigned bus number 3 [ 7.928597] ohci_hcd 0001:10:1b.0: irq 63, io mem 0xa0002000 [ 7.998398] hub 3-0:1.0: USB hub found [ 7.998411] hub 3-0:1.0: 3 ports detected [ 7.998475] ohci_hcd 0001:10:1b.1: enabling device (0000 -> 0002) [ 7.998493] ohci_hcd 0001:10:1b.1: OHCI Host Controller [ 7.998573] ohci_hcd 0001:10:1b.1: new USB bus registered, assigned bus number 4 [ 7.998599] ohci_hcd 0001:10:1b.1: irq 63, io mem 0xa0001000 [ 8.068383] hub 4-0:1.0: USB hub found [ 8.068396] hub 4-0:1.0: 2 ports detected [ 8.068522] usbcore: registered new interface driver libusual [ 8.068627] mice: PS/2 mouse device common for all mice [ 8.068699] PowerMac i2c bus pmu 2 registered [ 8.068742] PowerMac i2c bus pmu 1 registered [ 8.068773] PowerMac i2c bus mac-io 0 registered [ 8.068814] PowerMac i2c bus uni-n 0 registered [ 8.068857] PowerMac i2c bus uni-n 1 registered [ 8.069086] TCP cubic registered [ 8.069249] registered taskstats version 1 [ 8.069521] input: PMU as /devices/virtual/input/input1 [ 8.069575] Registered led device: pmu-led::front [ 8.069585] drivers/rtc/hctosys.c: unable to open rtc device (y) [ 8.069615] Freeing unused kernel memory: 196k init [ 8.112690] udev: starting version 151 [ 8.352137] usb 2-1: new full speed USB device using ohci_hcd and address 2 [ 8.395475] ide-gd driver 1.18 [ 8.417062] hda: max request size: 512KiB [ 8.438495] sungem.c:v0.98 8/24/03 David S. Miller (davem@redhat.com) [ 8.462503] ide-cd driver 5.00 [ 8.472248] hda: 156301488 sectors (80026 MB), CHS=16383/255/63 [ 8.472335] hda: cache flushes supported [ 8.472468] hda: [mac] hda1 hda2 hda3 hda4 [ 8.481296] ide-cd: hdc: ATAPI 24X DVD-ROM CD-R/RW drive, 2048kB Cache [ 8.481327] Uniform CD-ROM driver Revision: 3.20 [ 8.502496] PHY ID: 1410cc2, addr: 0 [ 8.503141] eth0: Sun GEM (PCI) 10/100/1000BaseT Ethernet 00:14:51:08:ac:8c [ 8.503168] eth0: Found Marvell 88E1111 PHY [ 8.503452] ohci1394 0002:24:0e.0: enabling device (0000 -> 0002) [ 8.557398] ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[40] MMIO=[f5000000-f50007ff] Max Packet=[4096] IR/IT contexts=[8/8] [ 8.718744] usb 2-2: new full speed USB device using ohci_hcd and address 3 [ 8.840620] EXT3-fs (hda3): recovery required on readonly filesystem [ 8.840650] EXT3-fs (hda3): write access will be enabled during recovery [ 8.939175] usbcore: registered new interface driver hiddev [ 8.958714] input: HID 05ac:1000 as /devices/pci0001:10/0001:10:1a.0/usb2/2-1/2-1:1.0/input/input2 [ 8.959033] generic-usb 0003:05AC:1000.0001: input,hidraw0: USB HID v1.11 Keyboard [HID 05ac:1000] on usb-0001:10:1a.0-1/input0 [ 8.996621] input: HID 05ac:1000 as /devices/pci0001:10/0001:10:1a.0/usb2/2-1/2-1:1.1/input/input3 [ 8.996963] generic-usb 0003:05AC:1000.0002: input,hidraw1: USB HID v1.11 Mouse [HID 05ac:1000] on usb-0001:10:1a.0-1/input1 [ 8.997930] usbcore: registered new interface driver usbhid [ 8.997949] usbhid: USB HID core driver [ 9.057031] input: Apple Computer Apple Internal Keyboard/Trackpad as /devices/pci0001:10/0001:10:1a.0/usb2/2-2/2-2:1.0/input/input4 [ 9.057782] apple 0003:05AC:020E.0003: input,hidraw2: USB HID v1.10 Keyboard [Apple Computer Apple Internal Keyboard/Trackpad] on usb-0001:10:1a.0-2/input0 [ 9.063904] input: Apple Computer Apple Internal Keyboard/Trackpad as /devices/pci0001:10/0001:10:1a.0/usb2/2-2/2-2:1.2/input/input5 [ 9.064059] apple 0003:05AC:020E.0004: input,hidraw3: USB HID v1.10 Device [Apple Computer Apple Internal Keyboard/Trackpad] on usb-0001:10:1a.0-2/input2 [ 9.347353] kjournald starting. Commit interval 5 seconds [ 9.347408] EXT3-fs (hda3): recovery complete [ 9.367818] EXT3-fs (hda3): mounted filesystem with writeback data mode [ 9.832228] ieee1394: Host added: ID:BUS[0-00:1023] GUID[001451fffe08ac8c] [ 33.702225] eth0: Link is up at 100 Mbps, full-duplex. [ 38.746141] Adding 3023748k swap on /dev/hda4. Priority:-1 extents:1 across:3023748k [ 38.805160] udev: starting version 151 [ 39.238884] usb 2-1: USB disconnect, address 2 [ 39.241343] usb 2-1: usbfs: USBDEVFS_CONTROL failed cmd hid2hci rqt 64 rq 0 len 0 ret -108 [ 39.362444] b43-pci-bridge 0001:10:12.0: enabling device (0004 -> 0006) [ 39.362492] ssb: Core 0 found: ChipCommon (cc 0x800, rev 0x04, vendor 0x4243) [ 39.362499] ssb: Core 1 found: IEEE 802.11 (cc 0x812, rev 0x05, vendor 0x4243) [ 39.362505] ssb: Core 2 found: PCMCIA (cc 0x80D, rev 0x02, vendor 0x4243) [ 39.362512] ssb: Core 3 found: V90 (cc 0x807, rev 0x02, vendor 0x4243) [ 39.362518] ssb: Core 4 found: PCI (cc 0x804, rev 0x09, vendor 0x4243) [ 39.399259] rtc-generic rtc-generic: rtc core: registered rtc-generic as rtc0 [ 39.424177] input: appletouch as /devices/pci0001:10/0001:10:1a.0/usb2/2-2/2-2:1.1/input/input6 [ 39.424312] usbcore: registered new interface driver appletouch [ 39.468844] ssb: Sonics Silicon Backplane found on PCI device 0001:10:12.0 [ 39.488859] EXT3-fs (hda3): using internal journal [ 39.621977] pmac_zilog: 0.6 (Benjamin Herrenschmidt ) [ 39.630005] ttyS0 at MMIO 0x80013020 (irq = 22) is a Z85c30 ESCC - Serial port [ 39.632477] ttyS1 at MMIO 0x80013000 (irq = 23) is a Z85c30 ESCC - Serial port [ 39.662315] usb 2-1: new full speed USB device using ohci_hcd and address 4 [ 39.750422] yenta_cardbus 0001:10:13.0: CardBus bridge found [0000:0000] [ 39.750444] yenta_cardbus 0001:10:13.0: Enabling burst memory read transactions [ 39.750450] yenta_cardbus 0001:10:13.0: Using CSCINT to route CSC interrupts to PCI [ 39.750454] yenta_cardbus 0001:10:13.0: Routing CardBus interrupts to PCI [ 39.750460] yenta_cardbus 0001:10:13.0: TI: mfunc 0x00001002, devctl 0x60 [ 39.769201] alloc irq_desc for 57 on node 0 [ 39.769209] alloc kstat_irqs on node 0 [ 39.769216] irq: irq 57 on host /pci@f2000000/mac-io@17/interrupt-controller@40000 mapped to virtual irq 57 [ 39.769252] alloc irq_desc for 58 on node 0 [ 39.769254] alloc kstat_irqs on node 0 [ 39.769258] irq: irq 58 on host /pci@f2000000/mac-io@17/interrupt-controller@40000 mapped to virtual irq 58 [ 39.775077] ams: Found I2C based motion sensor [ 39.852225] yenta_cardbus 0001:10:13.0: ISA IRQ mask 0x0000, PCI irq 53 [ 39.852265] yenta_cardbus 0001:10:13.0: Socket status: 30000007 [ 39.852343] yenta_cardbus 0001:10:13.0: pcmcia: parent PCI bridge I/O window: 0x0 - 0x7fffff [ 39.852349] yenta_cardbus 0001:10:13.0: pcmcia: parent PCI bridge Memory window: 0xf3000000 - 0xf3ffffff [ 39.852355] yenta_cardbus 0001:10:13.0: pcmcia: parent PCI bridge Memory window: 0x80000000 - 0xafffffff [ 40.084721] cfg80211: Calling CRDA to update world regulatory domain [ 40.144380] cfg80211: World regulatory domain updated: [ 40.144390] (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp) [ 40.144395] (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 40.144399] (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm) [ 40.144403] (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm) [ 40.144407] (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 40.144411] (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 40.327465] Bluetooth: Core ver 2.15 [ 40.342342] NET: Registered protocol family 31 [ 40.342349] Bluetooth: HCI device and connection manager initialized [ 40.342355] Bluetooth: HCI socket layer initialized [ 40.410000] Bluetooth: Generic Bluetooth USB driver ver 0.6 [ 40.415891] usbcore: registered new interface driver btusb [ 40.988829] NET: Registered protocol family 10 [ 40.989058] lo: Disabled Privacy Extensions [ 41.036792] eth0: Link is up at 100 Mbps, full-duplex. [ 41.036801] eth0: Pause is enabled (rxfifo: 10240 off: 7168 on: 5632) [ 41.062301] b43-phy0: Broadcom 4306 WLAN found (core revision 5) [ 41.070847] alloc irq_desc for 30 on node 0 [ 41.070855] alloc kstat_irqs on node 0 [ 41.070862] irq: irq 30 on host /pci@f2000000/mac-io@17/interrupt-controller@40000 mapped to virtual irq 30 [ 41.070892] alloc irq_desc for 21 on node 0 [ 41.070895] alloc kstat_irqs on node 0 [ 41.070898] irq: irq 1 on host /pci@f2000000/mac-io@17/interrupt-controller@40000 mapped to virtual irq 21 [ 41.070913] alloc irq_desc for 27 on node 0 [ 41.070915] alloc kstat_irqs on node 0 [ 41.070918] irq: irq 2 on host /pci@f2000000/mac-io@17/interrupt-controller@40000 mapped to virtual irq 27 [ 41.201624] snd-aoa-fabric-layout: Using PMF GPIOs [ 41.280346] snd-aoa-codec-tas: found tas3004 [ 41.281178] snd-aoa-fabric-layout: can use this codec [ 41.331749] phy0: Selected rate control algorithm 'minstrel' [ 41.332551] Registered led device: b43-phy0::tx [ 41.332576] Registered led device: b43-phy0::rx [ 41.332603] Registered led device: b43-phy0::radio [ 41.332751] Broadcom 43xx driver loaded [ Features: PL, Firmware-ID: FW13 ] [ 41.346227] alloc irq_desc for 61 on node 0 [ 41.346234] alloc kstat_irqs on node 0 [ 41.346241] irq: irq 61 on host /pci@f2000000/mac-io@17/interrupt-controller@40000 mapped to virtual irq 61 [ 41.346280] snd-aoa-codec-tas: tas found, addr 0x35 on /pci@f2000000/mac-io@17/i2c@18000/i2c-bus@0/codec@6a [ 41.393633] apm_emu: PMU APM Emulation initialized. [ 41.482134] b43 ssb0:0: firmware: requesting b43/ucode5.fw [ 41.516498] b43 ssb0:0: firmware: requesting b43/pcm5.fw [ 41.521590] NET: Registered protocol family 17 [ 41.571755] b43 ssb0:0: firmware: requesting b43/b0g0initvals5.fw [ 41.584570] b43 ssb0:0: firmware: requesting b43/b0g0bsinitvals5.fw [ 41.816630] SCSI subsystem initialized [ 41.826330] b43-phy0: Loading firmware version 410.2160 (2007-05-26 15:32:10) [ 41.886224] ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 41.983661] adt746x: version 1 (supported) [ 41.983670] adt746x: Thermostat bus: 1, address: 0x2e, limit_adjust: 0, fan_speed: -1 [ 41.983675] sensor 0: CPU/INTREPID BOTTOMSIDE [ 41.983678] sensor 1: CPU BOTTOMSIDE [ 41.983681] sensor 2: PWR SUPPLY BOTTOMSIDE [ 41.991079] adt746x: ADT7467 initializing [ 41.997303] adt746x: Lowering max temperatures from 81, 80, 87 to 70, 50, 70 [ 42.590086] hda: host max PIO4 wanted PIO0 selected PIO0 [ 42.650609] [drm:drm_mode_getfb] *ERROR* invalid framebuffer id [ 44.994194] Bluetooth: L2CAP ver 2.14 [ 44.994203] Bluetooth: L2CAP socket layer initialized [ 45.030593] Bluetooth: BNEP (Ethernet Emulation) ver 1.3 [ 45.030603] Bluetooth: BNEP filters: protocol multicast [ 45.091631] Bluetooth: SCO (Voice Link) ver 0.6 [ 45.091640] Bluetooth: SCO socket layer initialized