# File generated by xorgconfig. # # Copyright 2004 The X.Org Foundation # # Permission is hereby granted, free of charge, to any person obtaining a # copy of this software and associated documentation files (the "Software"), # to deal in the Software without restriction, including without limitation # the rights to use, copy, modify, merge, publish, distribute, sublicense, # and/or sell copies of the Software, and to permit persons to whom the # Software is furnished to do so, subject to the following conditions: # # The above copyright notice and this permission notice shall be included in # all copies or substantial portions of the Software. # # THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR # IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, # FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL # The X.Org Foundation BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, # WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, OUT OF # OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN THE # SOFTWARE. # # Except as contained in this notice, the name of The X.Org Foundation shall # not be used in advertising or otherwise to promote the sale, use or other # dealings in this Software without prior written authorization from # The X.Org Foundation. # # ********************************************************************** # Refer to the xorg.conf(5x) man page for details about the format of # this file. # ********************************************************************** # ********************************************************************** # Module section -- this section is used to specify # which dynamically loadable modules to load. # ********************************************************************** # Section "Module" # This loads the DBE extension module. Load "dbe" # Double buffer extension # This loads the miscellaneous extensions module, and disables # initialisation of the XFree86-DGA extension within that module. SubSection "extmod" Option "omit xfree86-dga" # don't initialise the DGA extension EndSubSection # This loads the font modules Load "type1" # Load "speedo" Load "freetype" # Load "xtt" # This loads the GLX module # Load "glx" # This loads the DRI module # Load "dri" EndSection # ********************************************************************** # Files section. This allows default font and rgb paths to be set # ********************************************************************** Section "Files" # The location of the RGB database. Note, this is the name of the # file minus the extension (like ".txt" or ".db"). There is normally # no need to change the default. RgbPath "/usr/X11R6/lib/X11/rgb" # Multiple FontPath entries are allowed (which are concatenated together), # as well as specifying multiple comma-separated entries in one FontPath # command (or a combination of both methods) # # FontPath "/usr/X11R6/lib/X11/fonts/misc/" # FontPath "/usr/X11R6/lib/X11/fonts/TTF/" FontPath "/usr/X11R6/lib/X11/fonts/Type1/" #FontPath "/usr/X11R6/lib/X11/fonts/CID/" FontPath "/usr/X11R6/lib/X11/fonts/75dpi/" FontPath "/usr/X11R6/lib/X11/fonts/100dpi/" #FontPath "/usr/X11R6/lib/X11/fonts/local/" FontPath "/usr/X11R6/lib/X11/fonts/Speedo/" # FontPath "/usr/X11R6/lib/X11/fonts/TrueType/" # FontPath "/usr/X11R6/lib/X11/fonts/freefont/" # The module search path. The default path is shown here. # ModulePath "/usr/X11R6/lib/modules" EndSection # ********************************************************************** # Server flags section. # ********************************************************************** Section "ServerFlags" # Uncomment this to cause a core dump at the spot where a signal is # received. This may leave the console in an unusable state, but may # provide a better stack trace in the core dump to aid in debugging # Option "NoTrapSignals" # Uncomment this to disable the VT switch sequence # (where n is 1 through 12). This allows clients to receive these key # events. # Option "DontVTSwitch" # Uncomment this to disable the server abort sequence # This allows clients to receive this key event. # Option "DontZap" # Uncomment this to disable the / mode switching # sequences. This allows clients to receive these key events. # Option "Dont Zoom" # Uncomment this to disable tuning with the xvidtune client. With # it the client can still run and fetch card and monitor attributes, # but it will not be allowed to change them. If it tries it will # receive a protocol error. # Option "DisableVidModeExtension" # Uncomment this to enable the use of a non-local xvidtune client. # Option "AllowNonLocalXvidtune" # Uncomment this to disable dynamically modifying the input device # (mouse and keyboard) settings. # Option "DisableModInDev" # Uncomment this to enable the use of a non-local client to # change the keyboard or mouse settings (currently only xset). # Option "AllowNonLocalModInDev" EndSection # ********************************************************************** # Input devices # ********************************************************************** # ********************************************************************** # Core keyboard's InputDevice section # ********************************************************************** Section "InputDevice" Identifier "Keyboard1" Driver "kbd" # For most OSs the protocol can be omitted (it defaults to "Standard"). # When using XQUEUE (only for SVR3 and SVR4, but not Solaris), # uncomment the following line. # Option "Protocol" "Xqueue" Option "AutoRepeat" "500 30" # Specify which keyboard LEDs can be user-controlled (eg, with xset(1)) # Option "Xleds" "1 2 3" # Option "LeftAlt" "Meta" # Option "RightAlt" "ModeShift" # To customise the XKB settings to suit your keyboard, modify the # lines below (which are the defaults). For example, for a non-U.S. # keyboard, you will probably want to use: # Option "XkbModel" "pc105" # If you have a US Microsoft Natural keyboard, you can use: # Option "XkbModel" "microsoft" # # Then to change the language, change the Layout setting. # For example, a german layout can be obtained with: # Option "XkbLayout" "de" # or: # Option "XkbLayout" "de" # Option "XkbVariant" "nodeadkeys" # # If you'd like to switch the positions of your capslock and # control keys, use: # Option "XkbOptions" "ctrl:swapcaps" # These are the default XKB settings for Xorg # Option "XkbRules" "xorg" # Option "XkbModel" "pc105" # Option "XkbLayout" "us" # Option "XkbVariant" "" # Option "XkbOptions" "" # Option "XkbDisable" Option "XkbRules" "xorg" Option "XkbModel" "pc105" Option "XkbLayout" "us" EndSection # ********************************************************************** # Core Pointer's InputDevice section # ********************************************************************** Section "InputDevice" # Identifier and driver Identifier "Mouse1" Driver "mouse" Option "Protocol" "PS/2" # PS/2 Mouse Option "Device" "/dev/input/mice" # When using XQUEUE, comment out the above two lines, and uncomment # the following line. # Option "Protocol" "Xqueue" # Mouse-speed setting for PS/2 mouse. # Option "Resolution" "256" # Baudrate and SampleRate are only for some Logitech mice. In # almost every case these lines should be omitted. # Option "BaudRate" "9600" # Option "SampleRate" "150" # Mouse wheel mapping. Default is to map vertical wheel to buttons 4 & 5, # horizontal wheel to buttons 6 & 7. Change if your mouse has more than # 3 buttons and you need to map the wheel to different button ids to avoid # conflicts. Option "ZAxisMapping" "4 5 6 7" # Emulate3Buttons is an option for 2-button mice # Emulate3Timeout is the timeout in milliseconds (default is 50ms) # Option "Emulate3Buttons" # Option "Emulate3Timeout" "50" # ChordMiddle is an option for some 3-button Logitech mice # Option "ChordMiddle" EndSection Section "InputDevice" Identifier "touchscreen1" Driver "dynapro" Option "Device" "/dev/ttyS1" Option "BaudRate" "9600" Option "SwapXY" "1" Option "DeviceName" "SC4" #Option "MinX" "0" # making this value larger makes # the pointer float further right # (when one's finger is at the # top-left) #Option "MaxX" "1024" #Option "MinY" "0" # making this smaller shrinks # the stage size # i.e. small = the pointer is lower when at the top # the pointer is higher when at the bottom #Option "MaxY" "760" # making this value larger makes the mouse float higher # when at the bottom half of the screen. # but does not appear to do anything when the pointer is at the top half! # Set to 880 for accuracy across the board. Option "AlwaysCore" Option "ScreenNumber" "0" Option "ReportingMode" "Raw" Option "ButtonNumber" "1" EndSection # ********************************************************************** # Other input device sections # this is optional and is required only if you # are using extended input devices. This is for example only. Refer # to the xorg.conf man page for a description of the options. # ********************************************************************** # # Section "InputDevice" # Identifier "Mouse2" # Driver "mouse" # Option "Protocol" "MouseMan" # Option "Device" "/dev/mouse2" # EndSection # # Section "InputDevice" # Identifier "spaceball" # Driver "magellan" # Option "Device" "/dev/cua0" # EndSection # # Section "InputDevice" # Identifier "spaceball2" # Driver "spaceorb" # Option "Device" "/dev/cua0" # EndSection # # Section "InputDevice" # Identifier "touchscreen0" # Driver "microtouch" # Option "Device" "/dev/ttyS0" # Option "MinX" "1412" # Option "MaxX" "15184" # Option "MinY" "15372" # Option "MaxY" "1230" # Option "ScreenNumber" "0" # Option "ReportingMode" "Scaled" # Option "ButtonNumber" "1" # Option "SendCoreEvents" # EndSection # # Section "InputDevice" # Identifier "touchscreen1" # Driver "elo2300" # Option "Device" "/dev/ttyS0" # Option "MinX" "231" # Option "MaxX" "3868" # Option "MinY" "3858" # Option "MaxY" "272" # Option "ScreenNumber" "0" # Option "ReportingMode" "Scaled" # Option "ButtonThreshold" "17" # Option "ButtonNumber" "1" # Option "SendCoreEvents" # EndSection # ********************************************************************** # Monitor section # ********************************************************************** # Any number of monitor sections may be present Section "Monitor" Identifier "Embedded LCD" # HorizSync is in kHz unless units are specified. # HorizSync may be a comma separated list of discrete values, or a # comma separated list of ranges of values. # NOTE: THE VALUES HERE ARE EXAMPLES ONLY. REFER TO YOUR MONITOR'S # USER MANUAL FOR THE CORRECT NUMBERS. HorizSync 31.5 - 57.0 # HorizSync 30-64 # multisync # HorizSync 31.5, 35.2 # multiple fixed sync frequencies # HorizSync 15-25, 30-50 # multiple ranges of sync frequencies # VertRefresh is in Hz unless units are specified. # VertRefresh may be a comma separated list of discrete values, or a # comma separated list of ranges of values. # NOTE: THE VALUES HERE ARE EXAMPLES ONLY. REFER TO YOUR MONITOR'S # USER MANUAL FOR THE CORRECT NUMBERS. VertRefresh 50-70 EndSection # ********************************************************************** # Graphics device section # ********************************************************************** # Any number of graphics device sections may be present # Standard VGA Device: Section "Device" Identifier "Standard VGA" VendorName "Unknown" BoardName "Unknown" # The chipset line is optional in most cases. It can be used to override # the driver's chipset detection, and should not normally be specified. # Chipset "generic" # The Driver line must be present. When using run-time loadable driver # modules, this line instructs the server to load the specified driver # module. Even when not using loadable driver modules, this line # indicates which driver should interpret the information in this section. Driver "vga" # The BusID line is used to specify which of possibly multiple devices # this section is intended for. When this line isn't present, a device # section can only match up with the primary video device. For PCI # devices a line like the following could be used. This line should not # normally be included unless there is more than one video device # intalled. # BusID "PCI:0:10:0" # VideoRam 256 # Clocks 25.2 28.3 EndSection # Device configured by xorgconfig: Section "Device" Identifier "Built-in card" Driver "i810" #VideoRam 1024 # Insert Clocks lines here if appropriate EndSection # ********************************************************************** # Screen sections # ********************************************************************** # Any number of screen sections may be present. Each describes # the configuration of a single screen. A single specific screen section # may be specified from the X server command line with the "-screen" # option. Section "Screen" Identifier "Screen 1" Device "Built-in card" Monitor "Embedded LCD" DefaultDepth 16 Subsection "Display" Depth 8 Modes "1024x768" "800x600" "640x480" ViewPort 0 0 EndSubsection Subsection "Display" Depth 16 Modes "1024x768" "800x600" "640x480" ViewPort 0 0 EndSubsection Subsection "Display" Depth 24 Modes "640x480" ViewPort 0 0 EndSubsection EndSection # ********************************************************************** # ServerLayout sections. # ********************************************************************** # Any number of ServerLayout sections may be present. Each describes # the way multiple screens are organised. A specific ServerLayout # section may be specified from the X server command line with the # "-layout" option. In the absence of this, the first section is used. # When now ServerLayout section is present, the first Screen section # is used alone. Section "ServerLayout" # The Identifier line must be present Identifier "Simple Layout" # Each Screen line specifies a Screen section name, and optionally # the relative position of other screens. The four names after # primary screen name are the screens to the top, bottom, left and right # of the primary screen. In this example, screen 2 is located to the # right of screen 1. Screen "Screen 1" # Each InputDevice line specifies an InputDevice section name and # optionally some options to specify the way the device is to be # used. Those options include "CorePointer", "CoreKeyboard" and # "SendCoreEvents". InputDevice "Mouse1" "CorePointer" # InputDevice "touchscreen1" "CorePointer" InputDevice "Keyboard1" "CoreKeyboard" EndSection # Section "DRI" # Mode 0666 # EndSection