[   87.565651] netpoll: netconsole: local port 12345
[   87.566075] netpoll: netconsole: local IPv4 address 0.0.0.0
[   87.566576] netpoll: netconsole: interface 'enp3s0'
[   87.566988] netpoll: netconsole: remote port 6666
[   87.567384] netpoll: netconsole: remote IPv4 address 192.168.15.100
[   87.567913] netpoll: netconsole: remote ethernet address ff:ff:ff:ff:ff:ff
[   87.568494] netpoll: netconsole: local IP 192.168.15.108
[   87.568967] console [netcon0] enabled
[   87.569282] netconsole: network logging started
[   99.847801] [drm:i915_dump_device_info], i915 device info: gen=7, pciid=0x0412 flags=need_gfx_hws,is_haswell,has_fbc,has_hotplug,has_llc,has_ddi,has_fpga_dbg,
[   99.849166] [drm:intel_detect_pch], Found LynxPoint PCH
[   99.849789] [drm] Memory usable by graphics device = 2048M
[   99.850254] [drm:i915_gem_gtt_init], GMADR size = 256M
[   99.850696] [drm:i915_gem_gtt_init], GTT stolen size = 32M
[   99.851162] checking generic (e0000000 500000) vs hw (e0000000 10000000)
[   99.851730] fb: conflicting fb hw usage inteldrmfb vs VESA VGA - removing generic driver
[   99.852447] Console: switching to colour dummy device 80x25
[   99.870683] [drm:intel_opregion_setup], graphic opregion physical addr: 0xdb9cd018
[   99.870694] [drm:intel_opregion_setup], Public ACPI methods supported
[   99.870696] [drm:intel_opregion_setup], SWSCI supported
[   99.894443] [drm:swsci_setup], SWSCI GBDA callbacks 00000cb3, SBCB callbacks 00300483
[   99.894453] [drm:intel_opregion_setup], ASLE supported
[   99.894516] i915 0000:00:02.0: irq 51 for MSI/MSI-X
[   99.894527] [drm] Supports vblank timestamp caching Rev 2 (21.10.2013).
[   99.894529] [drm] Driver supports precise vblank timestamp query.
[   99.894531] [drm:init_vbt_defaults], Set default to SSC at 120000 kHz
[   99.894534] [drm:intel_parse_bios], Using VBT from OpRegion: $VBT HASWELL        d
[   99.894536] [drm:parse_general_features], BDB_GENERAL_FEATURES int_tv_support 0 int_crt_support 0 lvds_use_ssc 0 lvds_ssc_freq 120000 display_clock_mode 0 fdi_rx_polarity_inverted 0
[   99.894539] [drm:parse_general_definitions], crt_ddc_bus_pin: 2
[   99.894543] [drm:parse_lfp_panel_data], Found panel mode in BIOS VBT tables:
[   99.894546] [drm:drm_mode_debug_printmodeline], Modeline 0:"1024x768" 0 65000 1024 1048 1184 1344 768 771 777 806 0x8 0xa
[   99.894548] [drm:parse_lfp_panel_data], VBT initial LVDS value 300
[   99.894551] [drm:parse_lfp_backlight], VBT backlight PWM modulation frequency 200 Hz, active high, min brightness 0, level 255
[   99.894553] [drm:parse_sdvo_panel_data], Found SDVO panel mode in BIOS VBT tables:
[   99.894557] [drm:drm_mode_debug_printmodeline], Modeline 0:"1600x1200" 0 162000 1600 1664 1856 2160 1200 1201 1204 1250 0x8 0xa
[   99.894559] [drm:parse_sdvo_device_mapping], No SDVO device info is found in VBT
[   99.894562] [drm:parse_mipi], No MIPI BDB found
[   99.894564] [drm:parse_ddi_port], Port B VBT info: DP:1 HDMI:1 DVI:1 EDP:0 CRT:0
[   99.894567] [drm:parse_ddi_port], VBT HDMI level shift for port B: 6
[   99.894569] [drm:parse_ddi_port], Port C VBT info: DP:0 HDMI:1 DVI:1 EDP:0 CRT:0
[   99.894571] [drm:parse_ddi_port], VBT HDMI level shift for port C: 6
[   99.894579] [drm:intel_dsm_pci_probe], no _DSM method for intel device
[   99.894585] [drm:i915_gem_init_stolen], found 33554432 bytes of stolen memory at dd200000
[   99.894614] vgaarb: device changed decodes: PCI:0000:00:02.0,olddecodes=io+mem,decodes=io+mem:owns=io+mem
[   99.894621] [drm:intel_print_wm_latency], Primary WM0 latency 20 (2.0 usec)
[   99.894623] [drm:intel_print_wm_latency], Primary WM1 latency 4 (2.0 usec)
[   99.894625] [drm:intel_print_wm_latency], Primary WM2 latency 36 (18.0 usec)
[   99.894627] [drm:intel_print_wm_latency], Primary WM3 latency 90 (45.0 usec)
[   99.894630] [drm:intel_print_wm_latency], Primary WM4 latency 160 (80.0 usec)
[   99.894632] [drm:intel_print_wm_latency], Sprite WM0 latency 20 (2.0 usec)
[   99.894634] [drm:intel_print_wm_latency], Sprite WM1 latency 4 (2.0 usec)
[  100.190535] [drm:i915_gem_setup_global_gtt], clearing unused GTT space: [0, 7ffff000]
[  100.191674] [drm:gen6_ppgtt_init], Allocated pde space (2M) at GTT entry: 0
[  100.191692] [drm:i915_gem_context_init], HW context support initialized
[  100.191699] [drm:init_status_page], render ring hws offset: 0x00211000
[  100.198614] [drm:init_pipe_control], render ring pipe control offset: 0x00232000
[  100.198621] [drm:init_status_page], bsd ring hws offset: 0x00233000
[  100.198667] [drm:init_status_page], blitter ring hws offset: 0x00254000
[  100.198709] [drm:init_status_page], video enhancement ring hws offset: 0x00275000
[  100.198814] [drm:intel_crt_reset], pch crt adpa set to 0xf40000
[  100.198819] [drm:intel_modeset_readout_hw_state], [CRTC:3] hw state readout: enabled
[  100.198821] [drm:intel_modeset_readout_hw_state], [CRTC:5] hw state readout: disabled
[  100.198824] [drm:intel_modeset_readout_hw_state], [CRTC:7] hw state readout: disabled
[  100.198826] [drm:intel_ddi_get_crtc_pll], Pipe A connected to port C using clock 0x80000000
[  100.198829] [drm:intel_modeset_readout_hw_state], [ENCODER:10:DAC-10] hw state readout: disabled, pipe A
[  100.198832] [drm:intel_modeset_readout_hw_state], [ENCODER:11:TMDS-11] hw state readout: disabled, pipe A
[  100.198834] [drm:intel_modeset_readout_hw_state], [ENCODER:16:TMDS-16] hw state readout: enabled, pipe A
[  100.198836] [drm:intel_modeset_readout_hw_state], [CONNECTOR:9:VGA-1] hw state readout: disabled
[  100.198839] [drm:intel_modeset_readout_hw_state], [CONNECTOR:12:DP-1] hw state readout: disabled
[  100.198841] [drm:intel_modeset_readout_hw_state], [CONNECTOR:15:HDMI-A-1] hw state readout: disabled
[  100.198843] [drm:intel_modeset_readout_hw_state], [CONNECTOR:17:HDMI-A-2] hw state readout: enabled
[  100.198846] [drm:intel_dump_pipe_config], [CRTC:3][setup_hw_state] config for pipe A
[  100.198848] [drm:intel_dump_pipe_config], cpu_transcoder: A
[  100.198850] [drm:intel_dump_pipe_config], pipe bpp: 24, dithering: 0
[  100.198852] [drm:intel_dump_pipe_config], fdi/pch: 0, lanes: 0, gmch_m: 0, gmch_n: 0, link_m: 0, link_n: 0, tu: 0
[  100.198854] [drm:intel_dump_pipe_config], dp: 0, gmch_m: 0, gmch_n: 0, link_m: 0, link_n: 0, tu: 0
[  100.198856] [drm:intel_dump_pipe_config], requested mode:
[  100.198859] [drm:drm_mode_debug_printmodeline], Modeline 0:"" 0 0 1280 0 0 0 1024 0 0 0 0x0 0x0
[  100.198860] [drm:intel_dump_pipe_config], adjusted mode:
[  100.198862] [drm:drm_mode_debug_printmodeline], Modeline 0:"" 0 0 0 0 0 0 0 0 0 0 0x0 0x5
[  100.198864] [drm:intel_dump_crtc_timings], crtc timings: 0 1280 1328 1440 1688 1024 1025 1028 1066, type: 0x0 flags: 0x5
[  100.198866] [drm:intel_dump_pipe_config], port clock: 0
[  100.198868] [drm:intel_dump_pipe_config], pipe src size: 1280x1024
[  100.198870] [drm:intel_dump_pipe_config], gmch pfit: control: 0x00000000, ratios: 0x00000000, lvds border: 0x00000000
[  100.198872] [drm:intel_dump_pipe_config], pch pfit: pos: 0x00000000, size: 0x05000400, enabled
[  100.198874] [drm:intel_dump_pipe_config], ips: 0
[  100.214579] [drm:intel_ironlake_crt_detect_hotplug], ironlake hotplug adpa=0x3f40000, result 1
[  100.312556] [drm:drm_edid_to_eld], ELD: no CEA Extension found
[  100.312569] [drm:drm_helper_probe_single_connector_modes], [CONNECTOR:17:HDMI-A-2] probed modes :
[  100.312573] [drm:drm_mode_debug_printmodeline], Modeline 24:"1280x1024" 60 108000 1280 1328 1440 1688 1024 1025 1028 1066 0x48 0x5
[  100.312576] [drm:drm_mode_debug_printmodeline], Modeline 30:"1280x1024" 75 135000 1280 1296 1440 1688 1024 1025 1028 1066 0x40 0x5
[  100.312579] [drm:drm_mode_debug_printmodeline], Modeline 25:"1152x864" 75 108000 1152 1216 1344 1600 864 865 868 900 0x40 0x5
[  100.312582] [drm:drm_mode_debug_printmodeline], Modeline 31:"1024x768" 75 78800 1024 1040 1136 1312 768 769 772 800 0x40 0x5
[  100.312584] [drm:drm_mode_debug_printmodeline], Modeline 32:"1024x768" 60 65000 1024 1048 1184 1344 768 771 777 806 0x40 0xa
[  100.312588] [drm:drm_mode_debug_printmodeline], Modeline 33:"800x600" 75 49500 800 816 896 1056 600 601 604 625 0x40 0x5
[  100.312590] [drm:drm_mode_debug_printmodeline], Modeline 26:"800x600" 60 40000 800 840 968 1056 600 601 605 628 0x40 0x5
[  100.312593] [drm:drm_mode_debug_printmodeline], Modeline 27:"640x480" 75 31500 640 656 720 840 480 481 484 500 0x40 0xa
[  100.312596] [drm:drm_mode_debug_printmodeline], Modeline 28:"640x480" 60 25200 640 656 752 800 480 490 492 525 0x40 0xa
[  100.312599] [drm:drm_mode_debug_printmodeline], Modeline 29:"720x400" 70 28320 720 738 846 900 400 412 414 449 0x40 0x6
[  100.312602] [drm:drm_setup_crtcs], 
[  100.312604] [drm:drm_enable_connectors], connector 9 enabled? yes
[  100.312606] [drm:drm_enable_connectors], connector 12 enabled? no
[  100.312608] [drm:drm_enable_connectors], connector 15 enabled? no
[  100.312610] [drm:drm_enable_connectors], connector 17 enabled? yes
[  100.312612] [drm:drm_target_preferred], looking for cmdline mode on connector 9
[  100.312614] [drm:drm_target_preferred], looking for preferred mode on connector 9
[  100.312617] [drm:drm_target_preferred], found mode 1024x768
[  100.312619] [drm:drm_target_preferred], looking for cmdline mode on connector 17
[  100.312621] [drm:drm_target_preferred], looking for preferred mode on connector 17
[  100.312623] [drm:drm_target_preferred], found mode 1280x1024
[  100.312625] [drm:drm_setup_crtcs], picking CRTCs for 8192x8192 config
[  100.312629] [drm:drm_setup_crtcs], desired mode 1024x768 set on crtc 3
[  100.312631] [drm:drm_setup_crtcs], desired mode 1280x1024 set on crtc 5
[  100.312634] [drm:intelfb_create], no BIOS fb, allocating a new one
[  100.312636] [drm:i915_gem_object_create_stolen], creating stolen object: size=500000
[  100.312642] [drm:i915_pages_create_for_stolen], offset=0x0, size=5242880
[  100.313331] [drm:intelfb_create], allocated 1280x1024 fb: 0x00296000, bo ffff880408d67e40