Attachment 17253 Details for Bug 12061 – my xorg.conf

my xorg.conf

xorg.conf (text/plain), 8.53 KB, created by Tobias Jakobi on 2008-06-20 06:46:46 UTC

(hide)

Description:

Filename:

MIME Type:

Creator: Tobias Jakobi

Created: 2008-06-20 06:46:46 UTC

Size: 8.53 KB

patch

obsolete

># **********************************************************************
># Refer to the xorg.conf(5x) man page for details about the format of 
># this file.
># **********************************************************************
>
># **********************************************************************
># Module section -- this  section  is used to specify
># which dynamically loadable modules to load.
># **********************************************************************
>
>Section "Module"
>
>	# This loads the miscellaneous extensions module, and disables
>	# initialisation of the XFree86-DGA extension within that module.
>	SubSection	"extmod"
>		Option		"omit xfree86-dga"   # don't initialise the DGA extension
>	EndSubSection
>
>	# Synaptics touchpad driver:
>	# Enables advanced functions of the pad
>	Load		"synaptics"
>
>EndSection
>
># **********************************************************************
># Files section.  This allows default font and rgb paths to be set
># **********************************************************************
>
>Section "Files"
>
># The location of the RGB database.  Note, this is the name of the
># file minus the extension (like ".txt" or ".db").  There is normally
># no need to change the default.
>
># Multiple FontPath entries are allowed (which are concatenated together),
># as well as specifying multiple comma-separated entries in one FontPath
># command (or a combination of both methods)
>
>	FontPath		"/usr/share/fonts/local/"
>	FontPath		"/usr/share/fonts/freefonts/"
>	FontPath		"/usr/share/fonts/corefonts/"
>
>	# cronyx fonts
>	FontPath		"/usr/share/fonts/cronyx/100dpi/:unscaled"
>	FontPath		"/usr/share/fonts/cronyx/misc/:unscaled"
>	FontPath		"/usr/share/fonts/cronyx/75dpi/:unscaled"
>
>	# terminus (Unicode-enabled) fonts
>	FontPath		"/usr/share/fonts/terminus/"
>
>	# intlfonts (Unicode-enabled)
>	FontPath		"/usr/share/fonts/intlfonts/"
>
># The module search path.  The default path is shown here.
>
>EndSection
>
># **********************************************************************
># Server flags section.
># **********************************************************************
>
>Section "ServerFlags"
>
># Uncomment this to cause a core dump at the spot where a signal is 
># received.  This may leave the console in an unusable state, but may
># provide a better stack trace in the core dump to aid in debugging
>
>#    Option "NoTrapSignals"
>
># Uncomment this to disable the <Crtl><Alt><Fn> VT switch sequence
># (where n is 1 through 12).  This allows clients to receive these key
># events.
>
>#    Option "DontVTSwitch"
>
># Uncomment this to disable the <Crtl><Alt><BS> server abort sequence
># This allows clients to receive this key event.
>
>#    Option "DontZap"
>
># Uncomment this to disable the <Crtl><Alt><KP_+>/<KP_-> mode switching
># sequences.  This allows clients to receive these key events.
>
>#    Option "Dont Zoom"
>
># Uncomment this to disable tuning with the xvidtune client. With
># it the client can still run and fetch card and monitor attributes,
># but it will not be allowed to change them. If it tries it will
># receive a protocol error.
>
>#    Option "DisableVidModeExtension"
>
># Uncomment this to enable the use of a non-local xvidtune client. 
>
>#    Option "AllowNonLocalXvidtune"
>
># Uncomment this to disable dynamically modifying the input device
># (mouse and keyboard) settings. 
>
>#    Option "DisableModInDev"
>
># Uncomment this to enable the use of a non-local client to
># change the keyboard or mouse settings (currently only xset).
>
>#    Option "AllowNonLocalModInDev"
>
>EndSection
>
>
># **********************************************************************
># Monitor section
># **********************************************************************
>
># Any number of monitor sections may be present
>
># The Modes section used for correct resolutions on the LCD
>Section "Modes"
>
>	Identifier	"60Hz LCD Modes"
>
>	# Implement only 60Hz modes (GTF):
>
>	# hsync: 49.68 kHz; pclk: 62.80 MHz
>	Modeline "960x800_60"  62.80  960 1008 1112 1264  800 801 804 828  -HSync +VSync
>
> 	# hsync: 29.82 kHz; pclk: 28.63 MHz
> 	Modeline "768x480_60"  28.63  768 784 864 960  480 481 484 497  -HSync +VSync
>
>EndSection
>
>Section "Monitor"
>
>	Identifier  "IntegratedLCD"
>
># HorizSync is in kHz unless units are specified.
># HorizSync may be a comma separated list of discrete values, or a
># comma separated list of ranges of values.
># NOTE: THE VALUES HERE ARE EXAMPLES ONLY.  REFER TO YOUR MONITOR'S
># USER MANUAL FOR THE CORRECT NUMBERS.
>
>	# the horizontal freq is not fixed to 60Hz because then
>	# only a few resolutions from the VESA BIOS are
>	# available in Xorg
>	HorizSync		20-80
>
>#    HorizSync	30-64         # multisync
>#    HorizSync	31.5, 35.2    # multiple fixed sync frequencies
>#    HorizSync	15-25, 30-50  # multiple ranges of sync frequencies
>
># VertRefresh is in Hz unless units are specified.
># VertRefresh may be a comma separated list of discrete values, or a
># comma separated list of ranges of values.
># NOTE: THE VALUES HERE ARE EXAMPLES ONLY.  REFER TO YOUR MONITOR'S
># USER MANUAL FOR THE CORRECT NUMBERS.
>
>	VertRefresh		55-65
>
>	Option			"DPMS"
>
>	UseModes		"60Hz LCD Modes"
>
>EndSection
>
>
># **********************************************************************
># Graphics device section
># **********************************************************************
>
># Any number of graphics device sections may be present
>
># Standard VGA Device:
>
>Section "Device"
>
>	Identifier	"Standard VESA"
>
># The chipset line is optional in most cases.  It can be used to override
># the driver's chipset detection, and should not normally be specified.
>
>	#Chipset	"generic"
>
># The Driver line must be present.  When using run-time loadable driver
># modules, this line instructs the server to load the specified driver
># module.  Even when not using loadable driver modules, this line
># indicates which driver should interpret the information in this section.
>
>	Driver		"vesa"
>
># The BusID line is used to specify which of possibly multiple devices
># this section is intended for.  When this line isn't present, a device
># section can only match up with the primary video device.  For PCI
># devices a line like the following could be used.  This line should not
># normally be included unless there is more than one video device
># intalled.
>
>	#BusID		"PCI:0:10:0"
>
>	#VideoRam	256
>
>	#Clocks		25.2 28.3
>
>EndSection
>
>Section "Device"
>
>	Identifier	"Intel 915GM/GMS/910GML"
>	
>	# intel driver supports the i915 chipset
>	Driver		"intel"
>
>	Option		"AccelMethod"		"EXA"
>	Option		"TripleBuffer"		"false"
>	Option		"BackingStore"		"true"
>	Option		"XvMC"			"false"
>
>EndSection
>
>
># **********************************************************************
># Screen sections
># **********************************************************************
>
># Any number of screen sections may be present.  Each describes
># the configuration of a single screen.  A single specific screen section
># may be specified from the X server command line with the "-screen"
># option.
>Section "Screen"
>
>	Identifier	"LCD Screen"
>
>	Device		"Intel 915GM/GMS/910GML"
>	#Device		"Standard VESA"
>	Monitor		"IntegratedLCD"
>
>	# at present XRandR can't change the colordepth on-the-fly
>	DefaultDepth 24
>
>	Subsection "Display"
>		Depth		8
>		Modes		"1280x800" "1024x768" "960x800_60" "800x600" "768x480_60" "640x480"
>		ViewPort	0 0
>	EndSubsection
>    
>	Subsection "Display"
>		Depth		16
>		Modes		"1280x800" "1024x768" "960x800_60" "800x600" "768x480_60" "640x480"
>		ViewPort	0 0
>	EndSubsection
>
>	Subsection "Display"
>		Depth		24
>		Modes		"1280x800" "1024x768" "960x800_60" "800x600" "768x480_60" "640x480"
>		ViewPort	0 0
>    EndSubsection
>
>EndSection
>
># **********************************************************************
># ServerLayout sections.
># **********************************************************************
>
># Any number of ServerLayout sections may be present.  Each describes
># the way multiple screens are organised.  A specific ServerLayout
># section may be specified from the X server command line with the
># "-layout" option.  In the absence of this, the first section is used.
># When now ServerLayout section is present, the first Screen section
># is used alone.
>
>Section "ServerLayout"
>
>	Identifier	"Standard Layout"
>
># Each Screen line specifies a Screen section name, and optionally
># the relative position of other screens.  The four names after
># primary screen name are the screens to the top, bottom, left and right
># of the primary screen.  In this example, screen 2 is located to the
># right of screen 1.
>
>	Screen		"LCD Screen"
>
>	Option		"BlankTime"			"10"
>	Option		"StandbyTime"			"15"
>	Option		"SuspendTime"			"20"
>	Option		"OffTime"			"25"
>
>EndSection
>
># Direct Rendering Interface
>Section "DRI"
>	Mode		0666
>EndSection

Actions: View

Attachments on bug 12061: 17253 | 17254 | 17255 | 17409

Use of freedesktop.org services, including Bugzilla, is subject to our Code of Conduct. How we collect and use information is described in our Privacy Policy.