Attachment 36526 Details for Bug 28671 – dmesg: first connector table patch

[patch] dmesg: first connector table patch

radeon-dmesg-conn-patch-2 (text/plain), 23.87 KB, created by Brett Witherspoon on 2010-06-26 13:03:58 UTC

(hide)

Description:

Filename:

MIME Type:

Creator: Brett Witherspoon

Created: 2010-06-26 13:03:58 UTC

Size: 23.87 KB

patch

obsolete

>Allocated 4096 bytes for 2 pacas at c00000000ffff000
>DART table allocated at: c00000007f000000
>Using PowerMac machine description
>Page orders: linear mapping = 24, virtual = 12, io = 12
>Found U3 memory controller & host bridge @ 0xf8000000 revision: 0xb3
>Mapped at 0xd000080080000000
>Found a K2 mac-io controller, rev: 32, mapped at 0xd000080080041000
>PowerMac motherboard: PowerMac G5
>DART IOMMU initialized for U3 type chipset
>bootconsole [udbg0] enabled
>CPU maps initialized for 1 thread per core
> (thread shift is 0)
>Starting Linux PPC64 #1 SMP Sat Jun 26 00:27:37 CDT 2010
>-----------------------------------------------------
>ppc64_pft_size                = 0x0
>physicalMemorySize            = 0xa0000000
>htab_address                  = 0xc00000011c000000
>htab_hash_mask                = 0x7ffff
>-----------------------------------------------------
>Linux version 2.6.34-gentoo-r1 (root@thepower) (gcc version 4.2.4 (Gentoo 4.2.4 p1.0)) #1 SMP Sat Jun 26 00:27:37 CDT 2010
>[boot]0012 Setup Arch
>Found U3-AGP PCI host bridge.  Firmware bus number: 240->255
>PCI host bridge /pci@0,f0000000  ranges:
> MEM 0x00000000f1000000..0x00000000f1ffffff -> 0x00000000f1000000 
>  IO 0x00000000f0000000..0x00000000f07fffff -> 0x0000000000000000
> MEM 0x0000000090000000..0x00000000afffffff -> 0x0000000090000000 
>Can't get bus-range for /ht@0,f2000000, assume bus 0
>Found U3-HT PCI host bridge.  Firmware bus number: 0->239
>PCI host bridge /ht@0,f2000000 (primary) ranges:
>via-pmu: Server Mode is disabled
>PMU driver v2 initialized for Core99, firmware: 0c
>nvram: Checking bank 0...
>nvram: gen0=1049, gen1=1048
>nvram: Active bank is: 0
>nvram: OF partition at 0x410
>nvram: XP partition at 0x1020
>nvram: NR partition at 0x1120
>Top of RAM: 0x120000000, Total RAM: 0xa0000000
>Memory hole size: 2048MB
>Zone PFN ranges:
>  DMA      0x00000000 -> 0x00120000
>  Normal   empty
>Movable zone start PFN for each node
>early_node_map[2] active PFN ranges
>    0: 0x00000000 -> 0x00080000
>    0: 0x00100000 -> 0x00120000
>On node 0 totalpages: 655360
>free_area_init_node: node 0, pgdat c0000000005a1a00, node_mem_map c0000000014c7000
>  DMA zone: 16128 pages used for memmap
>  DMA zone: 0 pages reserved
>  DMA zone: 639232 pages, LIFO batch:31
>[boot]0015 Setup Done
>PERCPU: Embedded 12 pages/cpu @c000000005400000 s19112 r0 d30040 u524288
>pcpu-alloc: s19112 r0 d30040 u524288 alloc=1*1048576
>pcpu-alloc: [0] 0 1 
>Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 639232
>Kernel command line: root=/dev/sda5 ro 
>PID hash table entries: 4096 (order: 3, 32768 bytes)
>Dentry cache hash table entries: 524288 (order: 10, 4194304 bytes)
>Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes)
>Memory: 2461552k/2621440k available (5624k kernel code, 2257040k reserved, 860k data, 194k bss, 272k init)
>SLUB: Genslabs=13, HWalign=128, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
>Hierarchical RCU implementation.
>NR_IRQS:512
>mpic: Setting up MPIC " MPIC 1   " version 1.2 at 80040000, max 4 CPUs
>mpic: ISU size: 120, shift: 7, mask: 7f
>mpic: Initializing for 120 sources
>irq: irq 56 on host /ht@0,f2000000/pci@3/mac-io@7/mpic@40000 mapped to virtual irq 56
>mpic: Setting up MPIC " MPIC 2   " version 1.2 at f8040000, max 4 CPUs
>mpic: ISU size: 120, shift: 7, mask: 7f
>mpic: Initializing for 120 sources
>time_init: decrementer frequency = 33.333333 MHz
>time_init: processor frequency   = 2000.000000 MHz
>clocksource: timebase mult[7800001] shift[22] registered
>clockevent: decrementer mult[8888887] shift[32] cpu[0]
>Console: colour dummy device 80x25
>console [tty0] enabled, bootconsole disabled
>Mount-cache hash table entries: 256
>PowerMac SMP probe found 2 cpus
>irq: irq 42 on host /u3@0,f8000000/mpic@f8040000 mapped to virtual irq 42
>KeyWest i2c @0xf8001003 irq 42 /u3@0,f8000000/i2c@f8001000
> channel 0 bus <multibus>
> channel 1 bus <multibus>
>irq: irq 26 on host /ht@0,f2000000/pci@3/mac-io@7/mpic@40000 mapped to virtual irq 26
>KeyWest i2c @0x80018000 irq 26 /ht@0,f2000000/pci@3/mac-io@7/i2c@18000
> channel 0 bus <multibus>
>PMU i2c /ht@0,f2000000/pci@3/mac-io@7/via-pmu@16000/pmu-i2c
> channel 1 bus <multibus>
> channel 2 bus <multibus>
>Processor timebase sync using Cypress i2c clock
>mpic: requesting IPIs...
>irq: irq 251 on host /ht@0,f2000000/pci@3/mac-io@7/mpic@40000 mapped to virtual irq 251
>irq: irq 252 on host /ht@0,f2000000/pci@3/mac-io@7/mpic@40000 mapped to virtual irq 252
>irq: irq 253 on host /ht@0,f2000000/pci@3/mac-io@7/mpic@40000 mapped to virtual irq 253
>irq: irq 254 on host /ht@0,f2000000/pci@3/mac-io@7/mpic@40000 mapped to virtual irq 254
>Processor 1 found.
>Brought up 2 CPUs
>devtmpfs: initialized
>NET: Registered protocol family 16
>PPC970/FX/MP performance monitor hardware support registered
>irq: irq 25 on host /ht@0,f2000000/pci@3/mac-io@7/mpic@40000 mapped to virtual irq 25
>irq: irq 47 on host /ht@0,f2000000/pci@3/mac-io@7/mpic@40000 mapped to virtual irq 47
>PCI: Probing PCI hardware
>pci 0000:f0:10.0: reg 10: [mem 0xa0000000-0xafffffff pref]
>pci 0000:f0:10.0: reg 14: [io  0x0400-0x04ff]
>pci 0000:f0:10.0: reg 18: [mem 0x90000000-0x9000ffff]
>pci 0000:f0:10.0: reg 30: [mem 0x90020000-0x9003ffff pref]
>pci 0000:f0:10.0: supports D1 D2
>IOMMU table initialized, virtual merging enabled
>irq: irq 48 on host /ht@0,f2000000/pci@3/mac-io@7/mpic@40000 mapped to virtual irq 48
>pci 0001:00:01.0: PCI bridge to [bus 06-06]
>pci 0001:00:01.0:   bridge window [io  0xf000-0x0000] (disabled)
>pci 0001:00:01.0:   bridge window [mem 0xfff00000-0x000fffff] (disabled)
>pci 0001:00:01.0:   bridge window [mem 0xfff00000-0x000fffff pref] (disabled)
>pci 0001:00:02.0: PCI bridge to [bus 07-07]
>pci 0001:00:02.0:   bridge window [io  0xf000-0x0000] (disabled)
>pci 0001:00:02.0:   bridge window [mem 0xfff00000-0x000fffff] (disabled)
>pci 0001:00:02.0:   bridge window [mem 0xfff00000-0x000fffff pref] (disabled)
>pci 0001:01:07.0: reg 10: [mem 0x80000000-0x8007ffff]
>pci 0001:01:08.0: reg 10: [mem 0x80081000-0x80081fff]
>pci 0001:01:09.0: reg 10: [mem 0x80080000-0x80080fff]
>pci 0001:00:03.0: PCI bridge to [bus 01-01]
>pci 0001:00:03.0:   bridge window [io  0xf000-0x0000] (disabled)
>pci 0001:00:03.0:   bridge window [mem 0x80000000-0x800fffff]
>pci 0001:00:03.0:   bridge window [mem 0x00000000-0x000fffff pref] (disabled)
>irq: irq 27 on host /ht@0,f2000000/pci@3/mac-io@7/mpic@40000 mapped to virtual irq 27
>irq: irq 28 on host /ht@0,f2000000/pci@3/mac-io@7/mpic@40000 mapped to virtual irq 28
>pci 0001:02:01.0: reg 10: [mem 0x80104000-0x80105fff]
>pci 0001:02:01.0: supports D1 D2
>pci 0001:02:01.0: PME# supported from D0 D1 D2 D3hot D3cold
>pci 0001:02:01.0: PME# disabled
>pci 0001:02:0b.0: reg 10: [mem 0x80102000-0x80102fff]
>pci 0001:02:0b.0: supports D1 D2
>pci 0001:02:0b.0: PME# supported from D0 D1 D2 D3hot D3cold
>pci 0001:02:0b.0: PME# disabled
>pci 0001:02:0b.1: reg 10: [mem 0x80101000-0x80101fff]
>pci 0001:02:0b.1: supports D1 D2
>pci 0001:02:0b.1: PME# supported from D0 D1 D2 D3hot D3cold
>pci 0001:02:0b.1: PME# disabled
>pci 0001:02:0b.2: reg 10: [mem 0x80100000-0x801000ff]
>pci 0001:02:0b.2: supports D1 D2
>pci 0001:02:0b.2: PME# supported from D0 D1 D2 D3hot D3cold
>pci 0001:02:0b.2: PME# disabled
>pci 0001:00:04.0: PCI bridge to [bus 02-02]
>pci 0001:00:04.0:   bridge window [io  0xf000-0x0000] (disabled)
>pci 0001:00:04.0:   bridge window [mem 0x80100000-0x801fffff]
>pci 0001:00:04.0:   bridge window [mem 0x00000000-0x000fffff pref] (disabled)
>irq: irq 57 on host /ht@0,f2000000/pci@3/mac-io@7/mpic@40000 mapped to virtual irq 57
>irq: irq 63 on host /ht@0,f2000000/pci@3/mac-io@7/mpic@40000 mapped to virtual irq 63
>pci 0001:03:0d.0: reg 10: [mem 0x80204000-0x80207fff]
>pci 0001:03:0e.0: reg 10: [mem 0x80200000-0x80200fff]
>pci 0001:03:0e.0: supports D1 D2
>pci 0001:03:0e.0: PME# supported from D0 D1 D2 D3hot
>pci 0001:03:0e.0: PME# disabled
>pci 0001:00:05.0: PCI bridge to [bus 03-03]
>pci 0001:00:05.0:   bridge window [io  0xf000-0x0000] (disabled)
>pci 0001:00:05.0:   bridge window [mem 0x80200000-0x802fffff]
>pci 0001:00:05.0:   bridge window [mem 0x00000000-0x000fffff pref] (disabled)
>irq: irq 39 on host /ht@0,f2000000/pci@3/mac-io@7/mpic@40000 mapped to virtual irq 39
>irq: irq 40 on host /ht@0,f2000000/pci@3/mac-io@7/mpic@40000 mapped to virtual irq 40
>pci 0001:04:0f.0: reg 10: [mem 0x80400000-0x805fffff]
>pci 0001:04:0f.0: reg 30: [mem 0x80300000-0x803fffff pref]
>pci 0001:00:06.0: PCI bridge to [bus 04-04]
>pci 0001:00:06.0:   bridge window [io  0xf000-0x0000] (disabled)
>pci 0001:00:06.0:   bridge window [mem 0x80300000-0x805fffff]
>pci 0001:00:06.0:   bridge window [mem 0x00000000-0x000fffff pref] (disabled)
>irq: irq 41 on host /ht@0,f2000000/pci@3/mac-io@7/mpic@40000 mapped to virtual irq 41
>pci 0001:05:0c.0: reg 10: [io  0x0000-0x0007]
>pci 0001:05:0c.0: reg 14: [io  0x0000-0x0003]
>pci 0001:05:0c.0: reg 18: [io  0x0000-0x0007]
>pci 0001:05:0c.0: reg 1c: [io  0x0000-0x0003]
>pci 0001:05:0c.0: reg 20: [io  0x0000-0x000f]
>pci 0001:05:0c.0: reg 24: [mem 0x80600000-0x80601fff]
>pci 0001:00:07.0: PCI bridge to [bus 05-05]
>pci 0001:00:07.0:   bridge window [io  0xf000-0x0000] (disabled)
>pci 0001:00:07.0:   bridge window [mem 0x80600000-0x806fffff]
>pci 0001:00:07.0:   bridge window [mem 0x00000000-0x000fffff pref] (disabled)
>irq: irq 0 on host /ht@0,f2000000/pci@3/mac-io@7/mpic@40000 mapped to virtual irq 16
>PCI 0000:f0 Cannot reserve Legacy IO [io  0x10000-0x10fff]
>pci 0001:00:01.0: PCI bridge to [bus 06-06]
>pci 0001:00:01.0:   bridge window [io  disabled]
>pci 0001:00:01.0:   bridge window [mem disabled]
>pci 0001:00:01.0:   bridge window [mem pref disabled]
>pci 0001:00:02.0: PCI bridge to [bus 07-07]
>pci 0001:00:02.0:   bridge window [io  disabled]
>pci 0001:00:02.0:   bridge window [mem disabled]
>pci 0001:00:02.0:   bridge window [mem pref disabled]
>pci 0001:00:03.0: PCI bridge to [bus 01-01]
>pci 0001:00:03.0:   bridge window [io  disabled]
>pci 0001:00:03.0:   bridge window [mem 0x80000000-0x800fffff]
>pci 0001:00:03.0:   bridge window [mem pref disabled]
>pci 0001:00:04.0: PCI bridge to [bus 02-02]
>pci 0001:00:04.0:   bridge window [io  disabled]
>pci 0001:00:04.0:   bridge window [mem 0x80100000-0x801fffff]
>pci 0001:00:04.0:   bridge window [mem pref disabled]
>pci 0001:00:05.0: PCI bridge to [bus 03-03]
>pci 0001:00:05.0:   bridge window [io  disabled]
>pci 0001:00:05.0:   bridge window [mem 0x80200000-0x802fffff]
>pci 0001:00:05.0:   bridge window [mem pref disabled]
>pci 0001:00:06.0: PCI bridge to [bus 04-04]
>pci 0001:00:06.0:   bridge window [io  disabled]
>pci 0001:00:06.0:   bridge window [mem 0x80300000-0x805fffff]
>pci 0001:00:06.0:   bridge window [mem pref disabled]
>pci 0001:00:07.0: PCI bridge to [bus 05-05]
>pci 0001:00:07.0:   bridge window [io  disabled]
>pci 0001:00:07.0:   bridge window [mem 0x80600000-0x806fffff]
>pci 0001:00:07.0:   bridge window [mem pref disabled]
>pci_bus 0000:f0: resource 0 [io  0x10000-0x80ffff]
>pci_bus 0000:f0: resource 1 [mem 0xf1000000-0xf1ffffff]
>pci_bus 0000:f0: resource 2 [mem 0x90000000-0xafffffff]
>pci_bus 0001:00: resource 0 [io  0x812000-0xc11fff]
>pci_bus 0001:00: resource 1 [mem 0xfa000000-0xffffffff]
>pci_bus 0001:00: resource 2 [mem 0x80000000-0x8fffffff]
>pci_bus 0001:00: resource 3 [mem 0xb0000000-0xefffffff]
>pci_bus 0001:01: resource 1 [mem 0x80000000-0x800fffff]
>pci_bus 0001:02: resource 1 [mem 0x80100000-0x801fffff]
>pci_bus 0001:03: resource 1 [mem 0x80200000-0x802fffff]
>pci_bus 0001:04: resource 1 [mem 0x80300000-0x805fffff]
>pci_bus 0001:05: resource 1 [mem 0x80600000-0x806fffff]
>PCI: Probing PCI hardware done
>Registering pmac pic with sysfs...
>bio: create slab <bio-0> at 0
>vgaarb: device added: PCI:0000:f0:10.0,decodes=io+mem,owns=mem,locks=none
>vgaarb: loaded
>SCSI subsystem initialized
>libata version 3.00 loaded.
>usbcore: registered new interface driver usbfs
>usbcore: registered new interface driver hub
>usbcore: registered new device driver usb
>Switching to clocksource timebase
>b43-pci-bridge 0001:02:01.0: enabling device (0004 -> 0006)
>ssb: Core 0 found: ChipCommon (cc 0x800, rev 0x02, vendor 0x4243)
>ssb: Core 1 found: IEEE 802.11 (cc 0x812, rev 0x04, vendor 0x4243)
>ssb: Core 2 found: PCMCIA (cc 0x80D, rev 0x01, vendor 0x4243)
>ssb: Core 3 found: V90 (cc 0x807, rev 0x01, vendor 0x4243)
>ssb: Core 4 found: PCI (cc 0x804, rev 0x07, vendor 0x4243)
>ssb: Core 5 found: IEEE 802.11 (cc 0x812, rev 0x04, vendor 0x4243)
>ssb: Sonics Silicon Backplane found on PCI device 0001:02:01.0
>NET: Registered protocol family 2
>IP route cache hash table entries: 131072 (order: 8, 1048576 bytes)
>TCP established hash table entries: 524288 (order: 11, 8388608 bytes)
>TCP bind hash table entries: 65536 (order: 8, 1048576 bytes)
>TCP: Hash tables configured (established 524288 bind 65536)
>TCP reno registered
>UDP hash table entries: 2048 (order: 4, 65536 bytes)
>UDP-Lite hash table entries: 2048 (order: 4, 65536 bytes)
>NET: Registered protocol family 1
>PCI: CLS mismatch (32 != 64), using 128 bytes
>pci 0001:00:01.0: MSI quirk detected; subordinate MSI disabled
>pci 0001:00:01.0: AMD8131 rev 12 detected; disabling PCI-X MMRBC
>pci 0001:00:02.0: MSI quirk detected; subordinate MSI disabled
>pci 0001:00:02.0: AMD8131 rev 12 detected; disabling PCI-X MMRBC
>nvram_init: Could not find nvram partition for nvram buffered error logging.
>Registering G5 CPU frequency driver
>Frequency method: i2c/pfunc, Voltage method: i2c/pfunc
>Low: 1304 Mhz, High: 2000 Mhz, Cur: 2000 MHz
>msgmni has been set to 4807
>alg: No test for stdrng (krng)
>Block layer SCSI generic (bsg) driver version 0.4 loaded (major 254)
>io scheduler noop registered
>io scheduler deadline registered
>io scheduler cfq registered (default)
>Generic RTC Driver v1.07
>MacIO PCI driver attached to K2 chipset
>irq: irq 32 on host /ht@0,f2000000/pci@3/mac-io@7/mpic@40000 mapped to virtual irq 32
>irq: irq 22 on host /ht@0,f2000000/pci@3/mac-io@7/mpic@40000 mapped to virtual irq 22
>irq: irq 5 on host /ht@0,f2000000/pci@3/mac-io@7/mpic@40000 mapped to virtual irq 17
>irq: irq 6 on host /ht@0,f2000000/pci@3/mac-io@7/mpic@40000 mapped to virtual irq 18
>irq: irq 23 on host /ht@0,f2000000/pci@3/mac-io@7/mpic@40000 mapped to virtual irq 23
>irq: irq 7 on host /ht@0,f2000000/pci@3/mac-io@7/mpic@40000 mapped to virtual irq 19
>irq: irq 8 on host /ht@0,f2000000/pci@3/mac-io@7/mpic@40000 mapped to virtual irq 20
>PowerMac G5 Thermal control driver 1.3
>Detected fan controls:
>  0: PWM fan, id 1, location: BACKSIDE,SYS CTRLR FAN
>  1: RPM fan, id 2, location: DRIVE BAY
>  2: PWM fan, id 2, location: SLOT,PCI FAN
>  3: RPM fan, id 3, location: CPU A INTAKE
>  4: RPM fan, id 4, location: CPU A EXHAUST
>  5: RPM fan, id 5, location: CPU B INTAKE
>  6: RPM fan, id 6, location: CPU B EXHAUST
>sata_svw 0001:05:0c.0: version 2.3
>scsi0 : sata_svw
>scsi1 : sata_svw
>scsi2 : sata_svw
>scsi3 : sata_svw
>ata1: SATA max UDMA/133 mmio m8192@0x80600000 port 0x80600000 irq 16
>ata2: SATA max UDMA/133 mmio m8192@0x80600000 port 0x80600100 irq 16
>ata3: SATA max UDMA/133 mmio m8192@0x80600000 port 0x80600200 irq 16
>ata4: SATA max UDMA/133 mmio m8192@0x80600000 port 0x80600300 irq 16
>pata-pci-macio 0001:03:0d.0: enabling device (0014 -> 0016)
>pata-pci-macio 0001:03:0d.0: Activating pata-macio chipset K2 ATA-6, Apple bus ID 3
>scsi4 : pata_macio
>ata5: PATA max UDMA/100 irq 39
>ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
>ehci_hcd 0001:02:0b.2: enabling device (0004 -> 0006)
>ehci_hcd 0001:02:0b.2: EHCI Host Controller
>ehci_hcd 0001:02:0b.2: new USB bus registered, assigned bus number 1
>ehci_hcd 0001:02:0b.2: irq 63, io mem 0x80100000
>ehci_hcd 0001:02:0b.2: USB 2.0 started, EHCI 1.00
>hub 1-0:1.0: USB hub found
>hub 1-0:1.0: 5 ports detected
>ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
>ohci_hcd 0001:01:08.0: enabling device (0000 -> 0002)
>ohci_hcd 0001:01:08.0: OHCI Host Controller
>ohci_hcd 0001:01:08.0: new USB bus registered, assigned bus number 2
>ohci_hcd 0001:01:08.0: irq 27, io mem 0x80081000
>hub 2-0:1.0: USB hub found
>hub 2-0:1.0: 2 ports detected
>ohci_hcd 0001:01:09.0: enabling device (0000 -> 0002)
>ohci_hcd 0001:01:09.0: OHCI Host Controller
>ohci_hcd 0001:01:09.0: new USB bus registered, assigned bus number 3
>ohci_hcd 0001:01:09.0: irq 28, io mem 0x80080000
>hub 3-0:1.0: USB hub found
>hub 3-0:1.0: 2 ports detected
>ata5.00: ATAPI: PIONEER DVD-RW  DVR-106D, A606, max UDMA/33
>ohci_hcd 0001:02:0b.0: enabling device (0000 -> 0002)
>ohci_hcd 0001:02:0b.0: OHCI Host Controller
>ohci_hcd 0001:02:0b.0: new USB bus registered, assigned bus number 4
>ohci_hcd 0001:02:0b.0: irq 63, io mem 0x80102000
>ata5.00: configured for UDMA/33
>hub 4-0:1.0: USB hub found
>hub 4-0:1.0: 3 ports detected
>ohci_hcd 0001:02:0b.1: enabling device (0000 -> 0002)
>ohci_hcd 0001:02:0b.1: OHCI Host Controller
>ohci_hcd 0001:02:0b.1: new USB bus registered, assigned bus number 5
>ohci_hcd 0001:02:0b.1: irq 63, io mem 0x80101000
>hub 5-0:1.0: USB hub found
>hub 5-0:1.0: 2 ports detected
>Initializing USB Mass Storage driver...
>usbcore: registered new interface driver usb-storage
>USB Mass Storage support registered.
>mice: PS/2 mouse device common for all mice
>i2c /dev entries driver
>PowerMac i2c bus pmu 2 registered
>PowerMac i2c bus pmu 1 registered
>PowerMac i2c bus mac-io 0 registered
>PowerMac i2c bus u3 1 registered
>PowerMac i2c bus u3 0 registered
>FCU Initialized, RPM fan shift is 3
>usbcore: registered new interface driver usbhid
>usbhid: USB HID core driver
>TCP cubic registered
>NET: Registered protocol family 17
>input: PMU as /devices/virtual/input/input0
>usb 4-1: new low speed USB device using ohci_hcd and address 2
>input: Logitech USB Trackball as /devices/pci0001:00/0001:00:04.0/0001:02:0b.0/usb4/4-1/4-1:1.0/input/input1
>generic-usb 0003:046D:C408.0001: input: USB HID v1.10 Mouse [Logitech USB Trackball] on usb-0001:02:0b.0-1/input0
>usb 5-2: new full speed USB device using ohci_hcd and address 2
>ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
>ata1.00: ATA-7: Maxtor 6Y250M0, YAR51FW0, max UDMA/133
>ata1.00: 490234752 sectors, multi 0: LBA48 
>hub 5-2:1.0: USB hub found
>hub 5-2:1.0: 3 ports detected
>ata1.00: configured for UDMA/133
>scsi 0:0:0:0: Direct-Access     ATA      Maxtor 6Y250M0   YAR5 PQ: 0 ANSI: 5
>sd 0:0:0:0: [sda] 490234752 512-byte logical blocks: (251 GB/233 GiB)
>sd 0:0:0:0: Attached scsi generic sg0 type 0
>sd 0:0:0:0: [sda] Write Protect is off
>sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
>sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
> sda: [mac] sda1 sda2 sda3 sda4 sda5 sda6 sda7
>sd 0:0:0:0: [sda] Attached SCSI disk
>usb 5-2.3: new full speed USB device using ohci_hcd and address 3
>input: Mitsumi Electric Apple Extended USB Keyboard as /devices/pci0001:00/0001:00:04.0/0001:02:0b.1/usb5/5-2/5-2.3/5-2.3:1.0/input/input2
>generic-usb 0003:05AC:020B.0002: input: USB HID v1.10 Keyboard [Mitsumi Electric Apple Extended USB Keyboard] on usb-0001:02:0b.1-2.3/input0
>input: Mitsumi Electric Apple Extended USB Keyboard as /devices/pci0001:00/0001:00:04.0/0001:02:0b.1/usb5/5-2/5-2.3/5-2.3:1.1/input/input3
>generic-usb 0003:05AC:020B.0003: input: USB HID v1.10 Device [Mitsumi Electric Apple Extended USB Keyboard] on usb-0001:02:0b.1-2.3/input1
>ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
>ata2.00: ATA-7: Maxtor 6Y250M0, YAR51FW0, max UDMA/133
>ata2.00: 490234752 sectors, multi 0: LBA48 
>ata2.00: configured for UDMA/133
>scsi 1:0:0:0: Direct-Access     ATA      Maxtor 6Y250M0   YAR5 PQ: 0 ANSI: 5
>sd 1:0:0:0: Attached scsi generic sg1 type 0
>sd 1:0:0:0: [sdb] 490234752 512-byte logical blocks: (251 GB/233 GiB)
>sd 1:0:0:0: [sdb] Write Protect is off
>sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00
>sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
> sdb: [mac] sdb1 sdb2 sdb3 sdb4 sdb5
>sd 1:0:0:0: [sdb] Attached SCSI disk
>ata3: SATA link down (SStatus 4 SControl 300)
>ata4: SATA link down (SStatus 4 SControl 300)
>scsi 4:0:0:0: CD-ROM            PIONEER  DVD-RW  DVR-106D A606 PQ: 0 ANSI: 5
>ata5.00: K2/Shasta alignment limits applied
>sr0: scsi3-mmc drive: 32x/32x writer cd/rw xa/form2 cdda tray
>Uniform CD-ROM driver Revision: 3.20
>sr 4:0:0:0: Attached scsi CD-ROM sr0
>sr 4:0:0:0: Attached scsi generic sg2 type 5
>EXT4-fs (sda5): mounted filesystem with ordered data mode
>VFS: Mounted root (ext2 filesystem) readonly on device 8:5.
>Freeing unused kernel memory: 272k freed
>udev: starting version 158
>Linux agpgart interface v0.103
>agpgart-uninorth 0000:f0:0b.0: Apple U3 chipset
>agpgart-uninorth 0000:f0:0b.0: configuring for size idx: 64
>agpgart-uninorth 0000:f0:0b.0: AGP aperture is 256M @ 0x0
>sungem.c:v0.98 8/24/03 David S. Miller (davem@redhat.com)
>PHY ID: 2062e0, addr: 1
>eth0: Sun GEM (PCI) 10/100/1000BaseT Ethernet 00:0a:95:ba:5e:34
>eth0: Found BCM5421-K2 PHY
>firewire_ohci 0001:03:0e.0: enabling device (0000 -> 0002)
>cfg80211: Calling CRDA to update world regulatory domain
>firewire_ohci: Added fw-ohci device 0001:03:0e.0, OHCI v1.0, 8 IR + 8 IT contexts, quirks 0x0
>irq: irq 30 on host /ht@0,f2000000/pci@3/mac-io@7/mpic@40000 mapped to virtual irq 30
>irq: irq 1 on host /ht@0,f2000000/pci@3/mac-io@7/mpic@40000 mapped to virtual irq 21
>irq: irq 2 on host /ht@0,f2000000/pci@3/mac-io@7/mpic@40000 mapped to virtual irq 24
>b43legacy-phy0: Broadcom 4306 WLAN found
>snd-aoa-fabric-layout: Using PMF GPIOs
>snd-aoa-codec-tas: found 'deq' node
>snd-aoa-fabric-layout: can use this codec
>phy0: Selected rate control algorithm 'minstrel'
>Broadcom 43xx-legacy driver loaded [ Features: PID, Firmware-ID: FW10 ]
>irq: irq 61 on host /ht@0,f2000000/pci@3/mac-io@7/mpic@40000 mapped to virtual irq 61
>irq: irq 60 on host /ht@0,f2000000/pci@3/mac-io@7/mpic@40000 mapped to virtual irq 60
>snd-aoa-codec-tas: tas found, addr 0x35 on /ht@0,f2000000/pci@3/mac-io@7/i2c@18000/deq@6a
>firewire_core: created device fw0: GUID 000a95fffeba5e34, S800
>[drm] Initialized drm 1.1.0 20060810
>[drm] radeon kernel modesetting enabled.
>radeon 0000:f0:10.0: enabling device (0006 -> 0007)
>[drm] initializing kernel modesetting (R420 0x1002:0x4A48).
>[drm] register mmio base: 0x90000000
>[drm] register mmio size: 65536
>radeon 0000:f0:10.0: Invalid ROM contents
>[drm] Not an x86 BIOS ROM, not using.
>[drm] GPU reset succeed (RBBM_STATUS=0x00000140)
>[drm] Using generic clock info
>[drm] radeon: power management initialized
>agpgart-uninorth 0000:f0:0b.0: putting AGP V3 device into 8x mode
>radeon 0000:f0:10.0: putting AGP V3 device into 8x mode
>radeon 0000:f0:10.0: GTT: 256M 0x00000000 - 0x0FFFFFFF
>[drm] Generation 2 PCI interface, using max accessible memory
>radeon 0000:f0:10.0: VRAM: 256M 0xA0000000 - 0xAFFFFFFF (256M used)
>[drm] radeon: irq initialized.
>[drm] Detected VRAM RAM=256M, BAR=256M
>[drm] RAM width 256bits DDR
>[TTM] Zone  kernel: Available graphics memory: 1230912 kiB.
>[drm] radeon: 256M of VRAM memory ready
>[drm] radeon: 256M of GTT memory ready.
>[drm] radeon: 4 quad pipes, 1 z pipes initialized.
>[drm] radeon: cp idle (0x10000C03)
>[drm] Loading R400 Microcode
>platform radeon_cp.0: firmware: requesting radeon/R420_cp.bin
>[drm] radeon: ring at 0x0000000000000000
>[drm] ring test succeeded in 0 usecs
>[drm] radeon: ib pool ready.
>[drm] ib test succeeded in 0 usecs
>[drm] Connector Table: 10 (mac x800)
>[drm] No valid Ext TMDS info found in BIOS
>[drm] No TMDS info found in BIOS
>[drm] No TV DAC info found in BIOS
>[drm] Radeon Display Connectors
>[drm] Connector 0:
>[drm]   DVI-I
>[drm]   HPD2
>[drm]   DDC: 0x64 0x64 0x64 0x64 0x64 0x64 0x64 0x64
>[drm]   Encoders:
>[drm]     DFP2: INTERNAL_DVO1
>[drm]     CRT1: INTERNAL_DAC1
>[drm]     DFP1: INTERNAL_TMDS1
>[drm]     CRT1: INTERNAL_DAC2
>No connectors reported connected with modes
>[drm] Initialized radeon 2.3.0 20080528 for 0000:f0:10.0 on minor 0
>Adding 524284k swap on /dev/sda4.  Priority:-1 extents:1 across:524284k 
>b43legacy ssb0:0: firmware: requesting b43legacy/ucode4.fw
>b43legacy ssb0:0: firmware: requesting b43legacy/pcm4.fw
>b43legacy ssb0:0: firmware: requesting b43legacy/b0g0initvals2.fw
>b43legacy-phy0: Loading firmware version 0x127, patch level 14 (2005-04-18 02:36:27)
>NET: Registered protocol family 10
>ADDRCONF(NETDEV_UP): wlan0: link is not ready
>wlan0: authenticate with 00:12:17:1b:d1:00 (try 1)
>wlan0: authenticated
>wlan0: associate with 00:12:17:1b:d1:00 (try 1)
>wlan0: RX AssocResp from 00:12:17:1b:d1:00 (capab=0x431 status=0 aid=2)
>wlan0: associated
>ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
>wlan0: no IPv6 routers present
>b43legacy-phy0 ERROR: PHY transmission error
>b43legacy-phy0 ERROR: PHY transmission error
>b43legacy-phy0 ERROR: PHY transmission error
>b43legacy-phy0 warning: Unexpected value for chanstat (0x7C00)
>b43legacy-phy0 ERROR: PHY transmission error

Actions: View | Splinter Review

Attachments on bug 28671: 36419 | 36421 | 36423 | 36424 | 36428 | 36429 | 36499 | 36500 | 36526 | 36527 | 36554 | 36556 | 37285

Use of freedesktop.org services, including Bugzilla, is subject to our Code of Conduct. How we collect and use information is described in our Privacy Policy.