Attachment 72491 Details for Bug 58984 – dmesg output

dmesg output

dmesg.log (text/plain), 20.41 KB, created by Patrick Baggett on 2013-01-03 23:31:49 UTC

(hide)

Description:

Filename:

MIME Type:

Creator: Patrick Baggett

Created: 2013-01-03 23:31:49 UTC

Size: 20.41 KB

patch

obsolete

>[    0.000000] PROMLIB: Sun IEEE Boot Prom 'OBP 4.17.1 2005/04/11 14:24'
>[    0.000000] PROMLIB: Root node compatible: 
>[    0.000000] Initializing cgroup subsys cpuset
>[    0.000000] Initializing cgroup subsys cpu
>[    0.000000] Linux version 3.8.0-rc1-figgles-00041-g73e5cf2 (root@ghost) (gcc version 4.6.3 (Debian 4.6.3-14) ) #1 SMP Wed Jan 2 20:18:12 CST 2013
>[    0.000000] bootconsole [earlyprom0] enabled
>[    0.000000] ARCH: SUN4U
>[    0.000000] Ethernet address: 00:03:ba:68:d3:2b
>[    0.000000] Kernel: Using 2 locked TLB entries for main kernel image.
>[    0.000000] Remapping the kernel... done.
>[    0.000000] OF stdout device is: /pci@1e,600000/isa@7/serial@0,3f8
>[    0.000000] PROM: Built device tree with 87111 bytes of memory.
>[    0.000000]  [4000000-47fffff] on node 0
>[    0.000000]  [6000000-67fffff] on node 0
>[    0.000000]  [20000000-207fffff] on node 1
>[    0.000000]  [24000000-247fffff] on node 1
>[    0.000000]  [26000000-267fffff] on node 1
>[    0.000000] Zone ranges:
>[    0.000000]   Normal   [mem 0x00000000-0x133fd9ffff]
>[    0.000000] Movable zone start for each node
>[    0.000000] Early memory node ranges
>[    0.000000]   node   0: [mem 0x00000000-0x3fffffff]
>[    0.000000]   node   0: [mem 0x200000000-0x23fffffff]
>[    0.000000]   node   0: [mem 0x300000000-0x33fffffff]
>[    0.000000]   node   1: [mem 0x1000000000-0x103fffffff]
>[    0.000000]   node   1: [mem 0x1200000000-0x123fffffff]
>[    0.000000]   node   1: [mem 0x1300000000-0x133effdfff]
>[    0.000000]   node   1: [mem 0x133f000000-0x133fd65fff]
>[    0.000000]   node   1: [mem 0x133fd86000-0x133fd9ffff]
>[    0.000000] On node 0 totalpages: 393216
>[    0.000000]   Normal zone: 3072 pages used for memmap
>[    0.000000]   Normal zone: 0 pages reserved
>[    0.000000]   Normal zone: 390144 pages, LIFO batch:15
>[    0.000000] On node 1 totalpages: 392895
>[    0.000000]   Normal zone: 3070 pages used for memmap
>[    0.000000]   Normal zone: 0 pages reserved
>[    0.000000]   Normal zone: 389825 pages, LIFO batch:15
>[    0.000000] Booting Linux...
>[    0.000000] CPU CAPS: [flush,stbar,swap,muldiv,v9,ultra3,mul32,div32]
>[    0.000000] CPU CAPS: [v8plus,vis,vis2]
>[    0.000000] PERCPU: Embedded 7 pages/cpu @fffff8033e000000 s22464 r8192 d26688 u4194304
>[    0.000000] pcpu-alloc: s22464 r8192 d26688 u4194304 alloc=1*4194304
>[    0.000000] pcpu-alloc: [0] 0 [1] 1 
>[    0.000000] Built 2 zonelists in Node order, mobility grouping on.  Total pages: 779969
>[    0.000000] Policy zone: Normal
>[    0.000000] Kernel command line: root=UUID=b4bd810b-44a1-4abe-b84d-35341b7a2388 ro
>[    0.000000] PID hash table entries: 4096 (order: 2, 32768 bytes)
>[    0.000000] Memory: 6222976k available (4032k kernel code, 1728k data, 248k init) [fffff80000000000,000000133fda0000]
>[    0.000000] Hierarchical RCU implementation.
>[    0.000000] 	CONFIG_RCU_FANOUT set to non-default value of 32
>[    0.000000] 	RCU dyntick-idle grace-period acceleration is enabled.
>[    0.000000] NR_IRQS:255
>[    0.000000] clocksource: mult[53555555] shift[24]
>[    0.000000] clockevent: mult[3126e98] shift[32]
>[    0.000000] Console: colour dummy device 80x25
>[    0.000000] console [tty0] enabled, bootconsole disabled
>[   56.109636] Calibrating delay using timer specific routine.. 24.02 BogoMIPS (lpj=48047)
>[   56.109653] pid_max: default: 32768 minimum: 301
>[   56.109817] Security Framework initialized
>[   56.109841] AppArmor: AppArmor disabled by boot time parameter
>[   56.110968] Dentry cache hash table entries: 1048576 (order: 10, 8388608 bytes)
>[   56.135438] Inode-cache hash table entries: 524288 (order: 9, 4194304 bytes)
>[   56.147374] Mount-cache hash table entries: 512
>[   56.148186] Initializing cgroup subsys cpuacct
>[   56.148203] Initializing cgroup subsys devices
>[   56.148212] Initializing cgroup subsys freezer
>[   56.148222] Initializing cgroup subsys net_cls
>[   56.148230] Initializing cgroup subsys blkio
>[   56.148239] Initializing cgroup subsys perf_event
>[   56.148554] Performance events: Supported PMU type is 'ultra3i'
>[   56.150710] CPU 0: synchronized TICK with master CPU (last diff 0 cycles, maxerr 5 cycles)
>[   56.150729] Brought up 2 CPUs
>[   56.150755] Testing NMI watchdog ... OK.
>[   56.231730] devtmpfs: initialized
>[   56.232528] regulator-dummy: no parameters
>[   56.232770] NET: Registered protocol family 16
>[   56.237391] /pci@1c,600000: TOMATILLO PCI Bus Module ver[4:0]
>[   56.237417] /pci@1c,600000: PCI IO[7ce01000000] MEM[7cf00000000]
>[   56.239021] PCI: Scanning PBM /pci@1c,600000
>[   56.239139] schizo f00672e0: PCI host bridge to bus 0000:00
>[   56.239164] pci_bus 0000:00: root bus resource [io  0x7ce01000000-0x7ce01ffffff] (bus address [0x0000-0xffffff])
>[   56.239190] pci_bus 0000:00: root bus resource [mem 0x7cf00000000-0x7cfffffffff] (bus address [0x00000000-0xffffffff])
>[   56.239215] pci_bus 0000:00: root bus resource [bus 00]
>[   56.239322] pci 0000:00:03.0: PME# supported from D3hot
>[   56.239563] /pci@1d,700000: TOMATILLO PCI Bus Module ver[4:0]
>[   56.239582] /pci@1d,700000: PCI IO[7c601000000] MEM[7c700000000]
>[   56.241242] PCI: Scanning PBM /pci@1d,700000
>[   56.241350] schizo f006feb0: PCI host bridge to bus 0001:00
>[   56.241373] pci_bus 0001:00: root bus resource [io  0x7c601000000-0x7c601ffffff] (bus address [0x0000-0xffffff])
>[   56.241398] pci_bus 0001:00: root bus resource [mem 0x7c700000000-0x7c7ffffffff] (bus address [0x00000000-0xffffffff])
>[   56.241423] pci_bus 0001:00: root bus resource [bus 00-01]
>[   56.241502] pci 0001:00:04.0: supports D1 D2
>[   56.241558] pci 0001:00:04.1: supports D1 D2
>[   56.241630] pci 0001:00:02.0: supports D1
>[   56.241638] pci 0001:00:02.0: PME# supported from D0 D1 D3hot
>[   56.242228] /pci@1e,600000: TOMATILLO PCI Bus Module ver[4:0]
>[   56.242247] /pci@1e,600000: PCI IO[7fe01000000] MEM[7ff00000000]
>[   56.243938] PCI: Scanning PBM /pci@1e,600000
>[   56.244041] schizo f0078524: PCI host bridge to bus 0002:00
>[   56.244064] pci_bus 0002:00: root bus resource [io  0x7fe01000000-0x7fe01ffffff] (bus address [0x0000-0xffffff])
>[   56.244089] pci_bus 0002:00: root bus resource [mem 0x7ff00000000-0x7ffffffffff] (bus address [0x00000000-0xffffffff])
>[   56.244113] pci_bus 0002:00: root bus resource [bus 00]
>[   56.244255] pci 0002:00:06.0: quirk: [io  0x7fe01000800-0x7fe0100083f] claimed by ali7101 ACPI
>[   56.244279] pci 0002:00:06.0: quirk: [io  0x7fe01000600-0x7fe0100061f] claimed by ali7101 SMB
>[   56.244361] pci 0002:00:08.0: supports D1 D2
>[   56.244369] pci 0002:00:08.0: PME# supported from D2 D3hot D3cold
>[   56.244448] pci 0002:00:0a.0: PME# supported from D3cold
>[   56.244513] pci 0002:00:0b.0: PME# supported from D3cold
>[   56.245193] /pci@1f,700000: TOMATILLO PCI Bus Module ver[4:0]
>[   56.245212] /pci@1f,700000: PCI IO[7f601000000] MEM[7f700000000]
>[   56.246973] PCI: Scanning PBM /pci@1f,700000
>[   56.247074] schizo f0080d94: PCI host bridge to bus 0003:00
>[   56.247096] pci_bus 0003:00: root bus resource [io  0x7f601000000-0x7f601ffffff] (bus address [0x0000-0xffffff])
>[   56.247120] pci_bus 0003:00: root bus resource [mem 0x7f700000000-0x7f7ffffffff] (bus address [0x00000000-0xffffffff])
>[   56.247144] pci_bus 0003:00: root bus resource [bus 00]
>[   56.249776] bio: create slab <bio-0> at 0
>[   56.250222] vgaarb: device added: PCI:0001:01:00.0,decodes=io+mem,owns=none,locks=none
>[   56.250249] vgaarb: loaded
>[   56.250259] vgaarb: bridge control possible 0001:01:00.0
>[   56.250957] /pci@1e,600000/isa@7/rtc@0,70: RTC regs at 0x7fe01000070
>[   56.251620] Switching to clocksource stick
>[   56.264580] NET: Registered protocol family 2
>[   56.265279] TCP established hash table entries: 65536 (order: 7, 1048576 bytes)
>[   56.268418] TCP bind hash table entries: 65536 (order: 7, 1048576 bytes)
>[   56.271338] TCP: Hash tables configured (established 65536 bind 65536)
>[   56.271610] TCP: reno registered
>[   56.271701] UDP hash table entries: 4096 (order: 4, 131072 bytes)
>[   56.272098] UDP-Lite hash table entries: 4096 (order: 4, 131072 bytes)
>[   56.272769] NET: Registered protocol family 1
>[   56.272871] pci 0002:00:07.0: Activating ISA DMA hang workarounds
>[   56.327707] PCI: Enabling device: (0002:00:0b.0), cmd 2
>[   56.383680] PCI: CLS 64 bytes, default 64
>[   56.383877] Unpacking initramfs...
>[   56.835988] Freeing initrd memory: 9348k freed
>[   56.836878] power: Control reg at 7fe01000800
>[   56.837291] chmc: UltraSPARC-IIIi memory controller at /memory-controller@0,0
>[   56.837324] chmc: UltraSPARC-IIIi memory controller at /memory-controller@1,0
>[   56.837689] audit: initializing netlink socket (disabled)
>[   56.837732] type=2000 audit(0.811:1): initialized
>[   56.865617] HugeTLB registered 4 MB page size, pre-allocated 0 pages
>[   56.866271] VFS: Disk quotas dquot_6.5.2
>[   56.866407] Dquot-cache hash table entries: 1024 (order 0, 8192 bytes)
>[   56.866869] msgmni has been set to 12172
>[   56.867575] alg: No test for stdrng (krng)
>[   56.867684] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 252)
>[   56.867705] io scheduler noop registered
>[   56.867716] io scheduler deadline registered
>[   56.867760] io scheduler cfq registered (default)
>[   56.868670] f00a7030: ttyS0 at MMIO 0x7fe010003f8 (irq = 24) is a 16550A
>[   56.868689] Console: ttyS0 (SU)
>[   66.050620] console [ttyS0] enabled
>[   66.096773] f00a8bac: ttyS1 at MMIO 0x7fe010002e8 (irq = 24) is a 16550A
>[   66.185463] [drm] Initialized drm 1.1.0 20060810
>[   66.246656] mousedev: PS/2 mouse device common for all mice
>[   66.320512] rtc_cmos rtc_cmos: rtc core: registered rtc_cmos as rtc0
>[   66.404051] rtc0: no alarms, 114 bytes nvram
>[   66.460433] drop_monitor: Initializing network drop monitor service
>[   66.543048] TCP: cubic registered
>[   66.586680] NET: Registered protocol family 10
>[   66.645623] mip6: Mobile IPv6
>[   66.684544] NET: Registered protocol family 17
>[   66.742910] Key type dns_resolver registered
>[   66.799312] registered taskstats version 1
>[   66.853535] rtc_cmos rtc_cmos: setting system clock to 2013-01-03 14:10:02 UTC (1357222202)
>[   66.998033] udevd[57]: starting version 175
>[   67.151350] pps_core: LinuxPPS API ver. 1 registered
>[   67.216683] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
>[   67.337061] SCSI subsystem initialized
>[   67.398428] PCI: Enabling device: (0001:00:04.0), cmd 147
>[   67.399065] sym0: <1010-66> rev 0x1 at pci 0001:00:04.0 irq 12
>[   67.438926] usbcore: registered new interface driver usbfs
>[   67.438959] usbcore: registered new interface driver hub
>[   67.527930] PTP clock support registered
>[   67.530660] tg3.c:v3.128 (December 03, 2012)
>[   67.530672] PCI: Enabling device: (0000:00:03.0), cmd 2
>[   67.595622] tg3 0000:00:03.0: vpd r/w failed.  This is likely a firmware bug on this device.  Contact the card vendor for a firmware update.
>[   67.655616] tg3 0000:00:03.0: vpd r/w failed.  This is likely a firmware bug on this device.  Contact the card vendor for a firmware update.
>[   67.715616] tg3 0000:00:03.0: vpd r/w failed.  This is likely a firmware bug on this device.  Contact the card vendor for a firmware update.
>[   67.718007] tg3 0000:00:03.0 eth0: Tigon3 [partno(none) rev 1002] (PCI:66MHz:64-bit) MAC address 00:03:ba:68:d3:2b
>[   67.718016] tg3 0000:00:03.0 eth0: attached PHY is 5703 (10/100/1000Base-T Ethernet) (WireSpeed[1], EEE[0])
>[   67.718022] tg3 0000:00:03.0 eth0: RXcsums[1] LinkChgREG[0] MIirq[0] ASF[0] TSOcap[1]
>[   67.718028] tg3 0000:00:03.0 eth0: dma_rwctrl[763f0000] dma_mask[32-bit]
>[   68.181017] usbcore: registered new device driver usb
>[   68.183958] sym0: No NVRAM, ID 7, Fast-80, LVD, parity checking
>[   68.224322] sym0: SCSI BUS has been reset.
>[   68.224336] scsi0 : sym-2.2.3
>[   68.417937] libata version 3.00 loaded.
>[   68.418329] PCI: Enabling device: (0001:00:04.1), cmd 147
>[   68.418709] PCI: Enabling device: (0002:00:0d.0), cmd 5
>[   68.418902] sym1: <1010-66> rev 0x1 at pci 0001:00:04.1 irq 13
>[   68.496152] scsi1 : pata_ali
>[   68.501727] sym1: No NVRAM, ID 7, Fast-80, LVD, parity checking
>[   68.542110] sym1: SCSI BUS has been reset.
>[   68.542130] scsi2 : sym-2.2.3
>[   68.705687] scsi3 : pata_ali
>[   68.706451] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
>[   68.829552] ata1: PATA max UDMA/100 cmd 0x7fe01000a00 ctl 0x7fe01000a18 bmdma 0x7fe01000a20 irq 30
>[   68.947463] ata2: PATA max UDMA/100 cmd 0x7fe01000a10 ctl 0x7fe01000a08 bmdma 0x7fe01000a28 irq 30
>[   71.358996] scsi 0:0:0:0: Direct-Access     SEAGATE  ST373207LSUN72G  045A PQ: 0 ANSI: 3
>[   71.465688] scsi target0:0:0: tagged command queuing enabled, command queue depth 16.
>[   71.568675] scsi target0:0:0: Beginning Domain Validation
>[   71.645903] scsi target0:0:0: FAST-80 WIDE SCSI 160.0 MB/s DT (12.5 ns, offset 31)
>[   71.753151] scsi target0:0:0: Ending Domain Validation
>[   76.183833] ata2.00: ATAPI: SAMSUNG CDRW/DVD SM-352B, T807, max UDMA/33
>[   76.270838] ata2.00: WARNING: ATAPI DMA disabled for reliability issues.  It can be enabled
>[   76.380733] ata2.00: WARNING: via pata_ali.atapi_dma modparam or corresponding sysfs node.
>[   76.503727] ata2.00: configured for UDMA/33
>[   76.559883] scsi 3:0:0:0: CD-ROM            SAMSUNG  CDRW/DVD SM-352B T807 PQ: 0 ANSI: 5
>[   76.667537] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
>[   76.750963] ohci_hcd 0002:00:0a.0: OHCI Host Controller
>[   76.820811] ohci_hcd 0002:00:0a.0: new USB bus registered, assigned bus number 1
>[   76.821354] sr0: scsi3-mmc drive: 1x/52x writer cd/rw xa/form2 cdda tray
>[   76.821359] cdrom: Uniform CD-ROM driver Revision: 3.20
>[   76.821643] sr 3:0:0:0: Attached scsi CD-ROM sr0
>[   76.828804] sd 0:0:0:0: [sda] 143374738 512-byte logical blocks: (73.4 GB/68.3 GiB)
>[   76.830442] sd 0:0:0:0: [sda] Write Protect is off
>[   76.830450] sd 0:0:0:0: [sda] Mode Sense: db 00 10 08
>[   76.832496] sd 0:0:0:0: [sda] Write cache: disabled, read cache: enabled, supports DPO and FUA
>[   76.845848]  sda: sda1 sda2 sda3 sda4 sda5
>[   76.851075] sd 0:0:0:0: [sda] Attached SCSI disk
>[   77.467854] ohci_hcd 0002:00:0a.0: irq 28, io mem 0x7ff01000000
>[   77.475828] sd 0:0:0:0: Attached scsi generic sg0 type 0
>[   77.476009] sr 3:0:0:0: Attached scsi generic sg1 type 5
>[   77.743668] usb usb1: New USB device found, idVendor=1d6b, idProduct=0001
>[   77.837859] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
>[   77.949498] usb usb1: Product: OHCI Host Controller
>[   78.030293] usb usb1: Manufacturer: Linux 3.8.0-rc1-figgles-00041-g73e5cf2 ohci_hcd
>[   78.137306] usb usb1: SerialNumber: 0002:00:0a.0
>[   78.198331] hub 1-0:1.0: USB hub found
>[   78.247629] hub 1-0:1.0: 2 ports detected
>[   78.301884] ohci_hcd 0002:00:0b.0: OHCI Host Controller
>[   78.370630] ohci_hcd 0002:00:0b.0: new USB bus registered, assigned bus number 2
>[   78.468490] ohci_hcd 0002:00:0b.0: irq 29, io mem 0x7ff02000000
>[   78.603635] usb usb2: New USB device found, idVendor=1d6b, idProduct=0001
>[   78.692927] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
>[   78.787852] usb usb2: Product: OHCI Host Controller
>[   78.843793] usb 1-2: new full-speed USB device number 2 using ohci_hcd
>[   78.937682] usb usb2: Manufacturer: Linux 3.8.0-rc1-figgles-00041-g73e5cf2 ohci_hcd
>[   79.038325] usb usb2: SerialNumber: 0002:00:0b.0
>[   79.059308] usb 1-2: New USB device found, idVendor=0430, idProduct=100e
>[   79.059315] usb 1-2: New USB device strings: Mfr=0, Product=0, SerialNumber=0
>[   79.062375] hub 1-2:1.0: USB hub found
>[   79.065299] hub 1-2:1.0: 4 ports detected
>[   79.369225] usb 1-2.4: new full-speed USB device number 3 using ohci_hcd
>[   79.471203] hub 2-0:1.0: USB hub found
>[   79.520480] hub 2-0:1.0: 2 ports detected
>[   79.537186] usb 1-2.4: New USB device found, idVendor=0430, idProduct=00a2
>[   79.537192] usb 1-2.4: New USB device strings: Mfr=0, Product=1, SerialNumber=0
>[   79.537197] usb 1-2.4: Product: Sun USB Keyboard
>[   79.840319] usbcore: registered new interface driver usbhid
>[   79.913615] usbhid: USB HID core driver
>[   79.969963] input: Sun USB Keyboard as /devices/root/f0078524/pci0002:00/0002:00:0a.0/usb1/1-2/1-2.4/1-2.4:1.0/input/input0
>[   80.116761] hid-generic 0003:0430:00A2.0001: input,hidraw0: USB HID v1.10 Keyboard [Sun USB Keyboard] on usb-0002:00:0a.0-2.4/input0
>[   80.333530] kjournald starting.  Commit interval 5 seconds
>[   80.333593] EXT3-fs (sda2): mounted filesystem with ordered data mode
>[   81.820630] udevd[343]: starting version 175
>[   82.617266] PCI: Enabling device: (0001:01:00.0), cmd 7
>[   82.618321] nouveau  [  DEVICE][0001:01:00.0] BOOT0  : 0x298200a2
>[   82.698550] nouveau  [  DEVICE][0001:01:00.0] Chipset: G98 (NV98)
>[   82.778684] nouveau  [  DEVICE][0001:01:00.0] Family : NV50
>[   82.852045] nouveau  [   VBIOS][0001:01:00.0] checking PRAMIN for image...
>[   82.859964] PCI: Enabling device: (0002:00:08.0), cmd 3
>[   82.942458] nouveau  [   VBIOS][0001:01:00.0] ... signature not found
>[   83.027192] nouveau  [   VBIOS][0001:01:00.0] checking PROM for image...
>[   83.342197] nouveau  [   VBIOS][0001:01:00.0] ... appears to be valid
>[   83.426863] nouveau  [   VBIOS][0001:01:00.0] using image from PROM
>[   83.510077] nouveau  [   VBIOS][0001:01:00.0] BIT signature found
>[   83.590208] nouveau  [   VBIOS][0001:01:00.0] version 62.98.42.00.00
>[   83.674157] nouveau  [ DEVINIT][0001:01:00.0] adaptor not initialised
>[   83.758865] nouveau  [   VBIOS][0001:01:00.0] running init tables
>[   83.892421] nouveau  [     PFB][0001:01:00.0] RAM type: DDR2
>[   83.966863] nouveau  [     PFB][0001:01:00.0] RAM size: 512 MiB
>[   84.044688] nouveau  [     PFB][0001:01:00.0]    ZCOMP: 960 tags
>[   85.407608] nouveau  [  PTHERM][0001:01:00.0] FAN control: none / external
>[   85.498078] nouveau  [  PTHERM][0001:01:00.0] Thermal management: disabled
>[   85.588508] nouveau  [  PTHERM][0001:01:00.0] Programmed thresholds [ 90(3), 95(3), 122(2), 135(5) ]
>[   85.708932] [TTM] Zone  kernel: Available graphics memory: 3116288 kiB
>[   85.794790] [TTM] Zone   dma32: Available graphics memory: 2097152 kiB
>[   85.880572] [TTM] Initializing pool allocator
>[   85.937798] nouveau  [     DRM] VRAM: 512 MiB
>[   85.995038] nouveau  [     DRM] GART: 512 MiB
>[   86.052521] Kernel unaligned access at TPC[103017ec] parse_bit_i_tbl_entry+0x84/0x18c [nouveau]
>[   86.167012] Kernel unaligned access at TPC[1030150c] parse_script_table_pointers+0x4/0x20 [nouveau]
>[   86.286039] Kernel unaligned access at TPC[103014e4] parse_bit_lvds_tbl_entry+0x44/0x68 [nouveau]
>[   86.402736] nouveau  [     DRM] TMDS table version 2.0
>[   86.470273] Kernel unaligned access at TPC[1030317c] olddcb_table+0xc8/0x18c [nouveau]
>[   86.574395] nouveau  [     DRM] DCB version 4.0
>[   86.633925] Kernel unaligned access at TPC[1030317c] olddcb_table+0xc8/0x18c [nouveau]
>[   86.738061] nouveau  [     DRM] DCB outp 00: 02000300 00000028
>[   86.814787] nouveau  [     DRM] DCB outp 01: 01000302 00020030
>[   86.891419] nouveau  [     DRM] DCB outp 02: 04011310 00000028
>[   86.968048] nouveau  [     DRM] DCB outp 03: 010223f1 00c0c080
>[   87.044698] nouveau  [     DRM] DCB conn 00: 00001030
>[   87.111105] nouveau  [     DRM] DCB conn 01: 00000200
>[   87.177439] nouveau  [     DRM] DCB conn 02: 00000110
>[   87.243774] nouveau  [     DRM] DCB conn 03: 00000111
>[   87.310109] nouveau  [     DRM] DCB conn 04: 00000113
>[   87.376949] [TTM] Finalizing pool allocator
>[   87.431979] [TTM] Zone  kernel: Used memory at exit: 0 kiB
>[   87.504054] [TTM] Zone   dma32: Used memory at exit: 0 kiB
>[   87.577019] nouveau: probe of 0001:01:00.0 failed with error -12
>[   89.247541] AC'97 1 does not respond - RESET
>[   89.319534] AC'97 1 access is not valid [0xffffffff], removing mixer.
>[   89.404180] ali mixer 1 creating error.
>[   90.197224] Adding 1911720k swap on /dev/sda4.  Priority:-1 extents:1 across:1911720k 
>[   90.683114] EXT3-fs (sda2): using internal journal
>[   90.893460] fuse init (API version 7.20)
>[   90.986153] loop: module loaded
>[   92.619636] kjournald starting.  Commit interval 5 seconds
>[   92.631290] EXT3-fs (sda5): using internal journal
>[   92.631296] EXT3-fs (sda5): mounted filesystem with ordered data mode
>[   93.965628] RPC: Registered named UNIX socket transport module.
>[   94.043479] RPC: Registered udp transport module.
>[   94.105306] RPC: Registered tcp transport module.
>[   94.167073] RPC: Registered tcp NFSv4.1 backchannel transport module.
>[   94.272700] FS-Cache: Loaded
>[   94.328940] FS-Cache: Netfs 'nfs' registered for caching
>[   94.418001] Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
>[   99.316402] tg3 0000:00:03.0 eth0: No firmware running
>[   99.423619] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
>[  102.380245] tg3 0000:00:03.0 eth0: Link is up at 1000 Mbps, full duplex
>[  102.467249] tg3 0000:00:03.0 eth0: Flow control is on for TX and on for RX
>[  102.557628] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready

Actions: View

Attachments on bug 58984: 72491 | 72526

Use of freedesktop.org services, including Bugzilla, is subject to our Code of Conduct. How we collect and use information is described in our Privacy Policy.