kernel 3.11-rc1 (also tested with 3.10 from Debian, 3.7, 3,2) # lspci -vnnn | grep VGA 00:02.0 VGA compatible controller [0300]: Intel Corporation 2nd Generation Core Processor Family Integrated Graphics Controller [8086:0116] (rev 09) (prog-if 00 [VGA controller]) 01:00.0 VGA compatible controller [0300]: Advanced Micro Devices, Inc. [AMD/ATI] Seymour [Radeon HD 6400M/7400M Series] [1002:6760] (rev ff) (prog-if ff) This is a HP Pavillon dv7 6130ez Sometimes, at random, the radeon card goes into full heat production mode. This seems to occur a while (a few minutes?) after wakeup from resume, however I'm not sure about that. Suspending and resuming the laptop a few times (1 <= x <= ~4) seems to calm the card down again. Power consumption according to powertop goes from ~14W up to ~50W. This happens even though the card should be in theory switched off. Aka: # cat /sys/kernel/debug/vgaswitcheroo/switch 0:IGD:+:Pwr:0000:00:02.0 1:DIS: :Off:0000:01:00.0 # echo IGD > /sys/kernel/debug/vgaswitcheroo/switch # echo OFF > /sys/kernel/debug/vgaswitcheroo/switch doesn't seem to have no effect whatsoever. It *seems* that setting "radeon.dpm=1" kernel boot options and then: # echo "battery" > /sys/class/drm/card$no/device/power_dpm_state puts the card in an "active" but "relatively low" power consumption mode. It is then using about 20W (instead of the "normal" ~14W) so it's continuously faning out slightly warm air. And it "seems that when the card is running in this mode, then it won't get so often, or ever (I'm not very sure) into the berserk heating mode. The lowest observed power consumption of the laptop is ~7W. It'd be very nice if it'd be possible to shut the card down electrically via software and stay in this 7W mode.
Created attachment 82828 [details] dmesg dmesg with wlan stuff edited out
So if I boot with "radeon.dpm=1" then, as allready described, the laptop uses "relatively little" power, and is faning off some heat continuously, even when I set: # echo "battery" > /sys/class/drm/card1/device/power_dpm_state Whether I do the following does *not* seem to matter: # echo IGD > /sys/kernel/debug/vgaswitcheroo/switch # echo OFF > /sys/kernel/debug/vgaswitcheroo/switch But if I boot *without* "radeon.dpm=1" then the laptop will stay cool without fans running out of the box using around 14W. The various settings will show this then: # cat /sys/class/drm/card1/device/power_method dpm # cat /sys/class/drm/card1/device/power_profile default # cat /sys/class/drm/card1/device/power_dpm_state balanced Weird that power_method would show "dpm" even though I have booted *without* "radeon.dpm=1" ?! When I then set: # echo "battery" > /sys/class/drm/card1/device/power_dpm_state Power consumption will drop even further to ~11W. The overal logic of all of this is evidently completely escaping me... 8-o
-- GitLab Migration Automatic Message -- This bug has been migrated to freedesktop.org's GitLab instance and has been closed from further activity. You can subscribe and participate further through the new bug through this link to our GitLab instance: https://gitlab.freedesktop.org/drm/amd/issues/358.
Use of freedesktop.org services, including Bugzilla, is subject to our Code of Conduct. How we collect and use information is described in our Privacy Policy.